Converters
Change a form or value and shows or transforms it into a different scale or value.
-
Product
16-Channel VME Analog/Thermocouple Input Module
V450
-
The V450 is a 16-channel 24-bit VME isolated analog-to-digital converter module which can acquire a wide range of DC voltages, including thermocouple readings with automatic cold junction compensation. Each channel is independently isolated with it's own A/D converter, signal conditioning, input protection circuits, and test relay.
-
Product
A/D Converters
-
Analog Devices A/D converters feature a variety of breakthrough capabilities enabling new system architectures that meet customer needs. Compact design, low power, and low cost are required by today's systems. Analog Devices offers the industry's largest range of A/D converter products that design engineers depend on for reliable performance in the harshest environments, both on Earth and in space. If you are looking for high quality and reliability while lowering cost and improving efficiency, consider using the industry's number one A/D converter products from Analog Devices.
-
Product
Temperature and humidity duct probe
T3113
-
Relative humidity, temperature sensors at 150mm stem. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
Product
MODEM ELIMINATOR
-
The UDC-ME allows two DTE devices (such as routers) to communicate within proximity of each other. The UDC-ME transmits data bi-directionally at clock rates of 1.2k up to 3.072Mbps between DTE devices. The unit is equipped with two interface slots that allow a host of serial interface cards to be utilized. The serial interface cards available are RS-232, RS-422/449, RS-530, X.21, V.35 and HSSI. The Serial Interface cards are interchangeable and may be mixed such as RS-232 to V.35 thus eliminating the need for an interface converter or changing expensive serial cards on a DTE device such as a router.
-
Product
4 Channel DAC FMC Module
DACNF04 – HPC
-
Sundance Multiprocessor Technology Ltd.
The RFM-DACNF04 is a four channel Digital to Analog converter FMC which complies with VITA 57.1-2010. Each channel provides 16-bit input and one DC coupled single-end analog output with DC – 250KHz sampling speed based on Linear Technology’s LTC2704-16. The 16-bit input data for each channel is provided through SPI from the FPGA on the FMC carrier board. A single-ended TTL level trigger output is provided from the FPGA.
-
Product
45~1050MHz FTTH CATV O/E Convertor
H9008A
-
Hangzhou Huatai Optic Tech. Co., Ltd.
Guangtai H9008A series CATV converter for digital television, fiber to the home. This machine adopts the high sensitivity optical receiving tube, without power supply, no power consumption. When the input optical power output level Pin=-1dBm, Vo=6 8dB V, can be economically and flexibly apply the integration of three networks, fiber to the home network application.
-
Product
WIFI Converter
-
When MRC meter with RS232 interface is connected to RSW-914, the meter can share data via WiFi technology. Therefore, personal devices, like desktop, laptop, smart phone, tablet... with WiFi function can be read the measuring data via WiFi. For example if factory installs Power analyzer DW-6095 along with RSW-914, then operator can monitor the power information (measuring value ) via WiFi network with safety.
-
Product
Infiniium S-Series High-Definition Oscilloscope: 2.5 GHz, 4 Analog Channels
DSOS254A
Oscilloscope
2.5 GHz bandwidth (upgradable)4 analog channels Capture a longer signal trace with 20 GSa/s max sample rate and 100 Mpts/channel of standard memory Get superior signal integrity with system ENOB of 7.4 bits and 10-bit analog-to-digital converter (ADC)Gain increased usability with the multi-touch supported 15 inch capacitive touch screen and solid state drive for fast boot and reliability Improve your testing with a wide range of protocol, compliance, and analysis software
-
Product
Net Radiometer
-
An on-board 24-bit A to D converter makes measurements and provides a digital SDI-12 output. This eliminates the need for multiple analog datalogger channels to measure each of the four components of net radiation.
-
Product
Digital Interface
DNTBOB-88
-
BOB 88 is a high quality, general purpose interface to transmit and receive line level analog audio signals via a Dante network. Analog inputs are converted to digital and appear on the network as transmit channels. Audio for the analog outputs is taken from subscriptions to transmit channels on the network from other sources. When connected to a network, each break out box will appear as a separate device in the Dante Controller software interface.
-
Product
AC/DC - On-board Converter Module
-
Mornsun Guangzhou Science & Technology
Mornsun AC/DC On-board Converter, one of the best-selling AC to DC converter power supplies, has a good market in the wholesale of AC to DC converter modules. On-board AC to DC converter modules are more frequently used in emerging applications. MORNSUN is expanding and enhancing its portfolio of board mount AC to DC converters to provide customers with a diverse selection of AC/DC converter module power supply in terms of package configurations (SIP, DIP, open-frame, chassis mount, etc.), input/output voltage options and multiple protections. These PCB mount AC to DC power converter modules cover power levels from 1W to 1000W, featuring compact size, standard or extra wide input voltage range, wide operating temperature range, high reliability, etc. Perfectly meet your design requirements for AC to DC converter power supply modules in different industrial applications.
-
Product
Hall Effect Speed Sensors
-
SPECTEC Innovative Sensor Solutions
SPECTEC zero speed Hall effect gear tooth sensors are used in industrial applications to determine shaft or gear speed or direction by detecting fluctuations in the magnetic field. The Hall effect technology fulfills a wide array of applications due to a Hall effect sensor's ability to detect zero speed and the quadrature sensor's ability to detect direction change. The Hall effect gear tooth sensor's digital output is easily read by computers, motion control devices, position monitors and digital to analog converters. Intrinsically Safe zero speed sensors are available for various applications.
-
Product
USB Signal Conditioning Products
-
Signal conditioning can include amplification, filtering, converting, range matching, isolation and any other processes required to make sensor output suitable for processing after conditioning. It is primarily utilized for data acquisition, in which sensor signals must be normalized and filtered to levels suitable for analog-to-digital conversion so they can be read by computerized devices.
-
Product
Embedded LO Capability
S96084B
-
Enables accurate measurement of relative phase and absolute group delay of a frequency converter with a built-in LO source, without having to access a common reference signal
-
Product
Down Converter
-
The products have a big Dynamic Range, are highly linear and have low Noise Figures to keep the best possible quality of the signals to be converted. For this reason an internal filter for secondary wave suppression is implemented.
-
Product
50-Watt DC/DC Converter; Dual Output
55JD1
DC Converter
NAI’s 55JD1 is a 50-Watt DC/DC Converter that accepts a +28 VDC input. This COTS unit provides full-power output, dual at a baseplate temperature of +100° C.
-
Product
DC/DC with UPS and Charge Controller
-
A wide input range, quad output PC/104-Plus DC/DC converter with a built-in battery charger and uninterruptable power supply (UPS) controller. Designed for harsh environments, the power supply operates from -40 to +85C without a fan or heatsink making it ideal for industrial applications.
-
Product
CATV Fiber Optic Receiver
MX862R
-
The MX862R is a Fiber Optics Receiver used to convert a fiber optic connection to RF (coax output).
-
Product
Waveguide Power Detector
-
RF Lambda’s waveguide power detectors are used to convert the RF power level to a DC voltage for signal power measurement. They offer wide band operation, fast response time and compact size.
-
Product
Ethernet/Serial Device Server
-
Advantech serial device servers and gateways convert legacy protocols and interfaces to satisfy your various industrial automation needs.
-
Product
UV Fluorescence TRS Analyzer
Model T102
-
Teledyne Advanced Pollution Instrumentation
The Model T102 TRS analyzer uses the proven UV fluorescence principle to measure Total Reduced Sulfur at levels commonly required for ambient air monitoring.The Model T102 uses a high temperature external converter set at 850°C to allow conversion of H2S, methyl mercaptan, dimethyldisulfide, and methyl-disulfide to SO2 at this temperature with efficiency greater than 98%. A switching option alternately measures TRS and SO2 while showing both readings concurrently on the front display.
-
Product
Power Meters
-
Chroma Systems Solutions, Inc.
Chroma’s Digital Power Meters are designed for both single-phase and multiple phase measurements of AC power signals and related parameters common to most electronic products. Instead of traditional analog measurement circuits the 66200 Digital Power Meter uses state-of-the-art DSP digitizing technology. The internal 16 bits analog/digital converters with sampling rates of up to 200KHz provide both high speed and high accuracy measurements which is unprecedented within the industry for this class of power meters current on the market.
-
Product
PXI Digital I/O Module With Power Distribution - With DC-DC Converter
40-228-001
Digital I/O
The 40-228 provides 32 channels of digital input and 32channels of digital output, together with switched +12V,+5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5Vsupply output. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter(40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
Product
USB / RS232 / RS485 / RS422 Opto Isolators
-
USB has now moved from the desktop to more challenging environments, including instrumentation, point of sales, factory & building automation, etc. With our rugged, industrial-grade USB isolators and USB to RS232 / RS485 / RS422 optically-isolated converters, we ensure that your assets are well protected from unexpected events.
-
Product
DC/DC Converter 1000 W
CRS-1000-6476-C
-
DC/DC converter with 1000 W from Premium | input ranges 14.4 - 30 VDC | output 48 V | operates in temperatures from -25 to +70 °C | designed according to EN50155
-
Product
16 A/D Channels (±100 VDC); 16-bit SAR per channel
ADF
-
Module ADF features 16 channels with up to 16-bit SAR A/D converters, simultaneous sampling. The maximum programmable, expected full-scale range input for the ADF module is -FS to +FS or 0 to FS; 100.00, 50.00, 25.0, 12.5 or 6.25 volts. The A/D converters have programmable sample rates of up to 200 kHz.
-
Product
Opto-Isolated Current Loop Signal
4029
-
SPECTEC Innovative Sensor Solutions
SPECTEC's Model 4029 digital opto-isolated current loop signal conditioner prevents ground loops and interrupts any galvanic signals riding on magnetic speed sensor's output signal.. This signal conditioner converts magnetic, variable reluctance and inductive sensors' sinusoidal signals into a 4-20 mA output suitable for interfacing with process control units, dataloggers, flow controllers, and computers.
-
Product
Pulse Generator
Traction Wheel Assembly
-
The complete and ready-to-install system converts linear travel/speeds to square-wave pulses/frequencies. • Square-wave frequency output, NPN open-collector • 5-28 VDC powered • 1 to 1,270 pulses per revolution (PPR - specify when ordering) • Optional bi-directional (quadrature) output models • 3 models: black neoprene rubber, smooth polyurethane, and diamond knurled aluminum tread
-
Product
cPCI to PMC Adapter / Carrier
cPCIBPMC
-
The cPCIBPMC ( cPCI to PMC ) adapter / carrier converter card provides the ability to install a PMC card into a standard cPCI slot. The cPCIBPMC has a PMC card slot mounted to a universal 3U 4HP cPCI card. Suitable for 32/64 with 33/ 66 MHz bus operation.
-
Product
Pressure Control Setup Using Pid Controller
ULP-26
-
Unitech Scales And Measurements Pvt. Ltd
Unitech’s Pressure Control Setup comprises of Pressure tank fitted with pressure transmitter to measure the pressure. The pressure is controlled by a pneumatic control valve operated by a I to P converter. The whole system is mounted on a Table top Model with all necessary Piping. The electronic panel comprises of ADC/DAC card with RS-232 interfaces.
