Converters
Change a form or value and shows or transforms it into a different scale or value.
-
product
16 Channel Isolated Analog Output Module
DP-cPCI-2502
The DP-cPCI-2502 is a 16 channel analog output module organized in four groups of 4 channels each. Each group is isolated with respect to each other and with respect to the system using optical isolators and DC-DC converters. Each output channel is driven by a 16 bit resolution precision DAC. The input digital data is converted to analog signals of ±10V range. The digital data for the DACs is written from the cPCI interface via two banks of latches enabling a double buffered output scheme.
-
product
Compressed Air RH+T Transmitter
T3419P-4
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Thermal Imagers & Industrial Endoscopes
GAOTek has developed advanced thermal imagers that are high quality, affordable, and accurate. Thermal imager is a non-contact temperature measurement device. It detects the infrared energy transmitted, reflected or emitted by all materials at a temperature above absolute zero. The energy factor is converted into a temperature reading or thermogram. Thermogram is the thermal image radiation produced that is displayed by the camera object emitting infrared energy. Thermal imagers are widely used for finding potential problems in applications across disciplines.
-
product
BNC (M) To Multi-Stacking Banana Plugs
3957
BNC (m) to multi-stacking banana plugs. Converts BNC (Female) cables/connectors to top/side stackable banana plugs for test versatility. BNC connector and banana plugs are molded directly to the wire for pull strength durability anddust/moisture resistance.
-
product
Electrochemical Converter
C800
The Control 800 series of electrochemical converters combines high performance digital conductivity and analog pH measurements with intuitive operation. It has been designed for easy integration into skids and panels to cover a wide range of bioprocess applications in both, conventional stainless steel and single-use systems.
-
product
PWM TO VOLTAGE SIGNAL CONVERTER
RCPWM2V
The RCPWM2V is a device that converts a standard hobby RC signal (1-2ms pulse) into a proportional analog voltage (0-5V). In many electronics applications the main processor is constantly busy and does not have the ability to address the time-sensitive PWM signal from an RC receiver immediately. This results in signal distortion or a sluggish response due to the extra filtering required. The RCPWM2V provides a simple solution by converting the signal into an analog signal. The main processor can then read the signal whenever it has time.
-
product
PXIe-4139 , ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit
782856-03
PXIe, ±60 V, ±3 A DC, ±10 A Pulsed, 40 W DC, 100 fA Precision System PXI Source Measure Unit - The PXIe-4139 is a high-precision, system source measure unit (SMU) that features 4-quadrant operation and sources up to 40 W of DC power. This module features analog-to-digital converters that help you perform high-precision measurements with a current resolution of 100 fA or high-speed acquisitions up to 1.8 MS/s. The module can maximize stability and measurement accuracy with SourceAdapt technology, which you can use to tune the transient response to match the characteristics of any load. You can use the PXIe-4139 for applications including manufacturing test, board-level test, and lab characterization with devices such as ICs, power management ICs (PMICs), and RFICs and discrete devices including LEDs and optical transceivers.
-
product
Hall Effect Sensors
The Mors Smitt transducers are used to measure high currents in rolling stock and trackside applications. High currents are converted linearly to low power signals.
-
product
PXI Digital I/O Module With Power Distribution - Without DC-DC Converter
40-228-002
The 40-228 provides 32 channels of digital input and 32 channels of digital output, together with switched +12V, +5V, +3.3V and -12V supply outputs derived from the PXI backplane. The module is available fitted with a DC-DC converter (40-228-001) which provides an additional -5V supply ouput. Alternatively the module can be supplied with an industry standard footprint for a DC-DC converter (40-228-002) allowing the user to fit one of their own specification if required. The 40-228 includes a breadboard area that allows users to add their own circuitry to the module.
-
product
HFC 8 Ways Return Path Optical Receiver
HR2080A, HR2080B
Hangzhou Huatai Optic Tech. Co., Ltd.
HR2080 series HFC 8 ways return path receiver can convert upstream optical signal to RF signal at the head-end and remote control center. 8 independent receivers integrated into a 1RU 19” casing to supply service for HFC network terminal. Receiver's low noise design, -22dBm receive sensitivity can provide service to farther place. There are two versions of this receiver. HR2080A with LCD on the front panel, HR2080B without LCD. All receivers are temperature tolerance type can be installed in any network surroundings including out-door type. Both of these two types can adopt SNMP function which can control the front panel to realize optimization work at the head-end and remote installment.
-
product
4-Ch 1.25 GHz, 16-bit D/A with DUC, Extended Interpolation, Virtex-6 - PCIe
Model 78671
Model 78671 is a member of the Cobalt® family of high performance PCIe boards based on the Xilinx Virtex-6 FPGA. This 4-channel, high-speed data converter issuitable for connection to transmit HF or IF ports of a communications or radar system. Its built-in data playback features offer an ideal turnkey solution for demandingtransmit applications.
-
product
4-Channel 200 MHz, 16-bit A/D with Virtex-7 FPGA - PCIe
Model 78760
Model 78760 is a member of the Onyx® family of high-performance PCIe boards based on the Xilinx Virtex-7 FPGA. A multichannel, high-speed data converter, it is suitable for connection to HF or IF ports of a communications or radar system.
-
product
FlexRIO Digitizer Device
FlexRIO Digitizer Devices feature high-performance analog-to-digital converters with lightweight analog front-ends designed to maximize sample rate, bandwidth, and dynamic range. These devices use FPGAs from Xilinx alongside LabVIEW and Vivado programming options for custom algorithm implementation and real-time signal processing. These devices also feature an auxiliary I/O connector with GPIO for triggering or digital interfacing and the option for high-speed serial communication.
-
product
DC/DC Converter 3.5 W
REM3.5E-1212D/R6/A/SMD
DC/DC converter with 3.5 W from Recom | input ranges 9 - 18 VDC | outputs +/-12 V | operates in ambient temperature from -40 to +95 °C | SMT package
-
product
Energy Saving Static Converter
The ENERGY SAVING static converter serves to generate a controlled squarewave single-phase alternate voltage (low frequency: 25 ÷ 125Hz) for industrial applications requiring high load power supplied by an external matching transformer. The power supply, sectioned by remote control switch and external fuses, is fed by a three-phase electric line via uncontrolled diode bridge and filtered by inductor and capacitor battery. The DC voltage thus obtained is converted into single-phase alternating voltage via “H”-shape bridge of semiconductors in order to control impressed frequency single-phase transformers.
-
product
AC/DC Linear Power Supply
Linear AC-DC power supplies are electronic devices used to convert electrical energy from alternating current (AC) to direct current (DC), providing a stable and regulated power supply for electronic devices. They are represented by the DA series.Linear power supplies of the DA series are characterised by their low output noise and high speed. They can be used as power amplifiers; a sinusoidal voltage of 8/10 Vpp can be superimposed on the test voltage up to a frequency of 50 kHz.Another application for this power supply family is the simulation of the curve of a photovoltaic panel by programming the voltage and current.
-
product
ATE For Data Communications Equipment
• Developed for DRS Codem Systems, Inc. to test the CTM-IP product line of the Multi-Interface Protocol Converter.• Manufacturing Test support for the CTM-IP chassis and Interface Modules. Functional test of signaling, protocol and software configurations for various communication interface configurations.• Regression Test support for Engineering Product Development. Configurable test sequencing allows engineer to select specific tests for execution, with the ability to exercise all combinations of data rates and interface configurations.
-
product
DrMOS (Driver + FET)
Renesas' high-performance DrMOS power modules combine a high-performance FET driver and MOSFETs in an advanced package to create high-density DC/DC converters.
-
product
Compact Differential Pressure Transmitters
Series 668B/D
Our low cost SERIES 668B/D Compact Differential Pressure Transmitters are capable of sensing differential gage pressure with ±0.8% FS accuracy, and converts this pressure difference to a proportional high level analog output for both unidirectional and bi-directional pressure ranges. These transmitters can withstand up to 15 psig overpressure with no damage to the unit. The compact, lightweight design makes installation simple and easy. Units are protected against incorrect wiring, and include a protective terminal cover.
-
product
PXIe-4305, 24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module
783868-01
24-Bit, 32-Channel, 51.2 kS/s, 42 V, PXI Analog Input Module—The PXIe‑4305 is a filtered analog input module for higher voltage measurements. The module offers the ability to select a digital filter per channel to provide extra filtering performance. You also can operate up to four different sample rates and triggering configurations concurrently to ensure you measure every sensor as needed. The module has an A/D converter per channel to enable a simultaneous sample rate at the maximum sample rate across the input range. The included NI‑DAQmx driver simplifies hardware configuration and measurement.
-
product
External Input Module
EIM-01
The EIM-01 external input module is used to safely isolate and input an external drive signal into the MAC-01, -02 or -03 AC Power Sources/Frequency Converters. The unit can accept various waveforms from laboratory or programmable oscillators or from a Titan MOS-01, -01A, -01B when used as a slave unit in multi-KVA systems. BNC input is completely isolated and floating with 1,500VAC breakdown and excellent common mode rejection. A recessed 8% gain adjustment control is also provided. The EIM-01 must be factory installed.
-
product
Principle Of MALDI/TOFMS
MALDI is the abbreviation for "Matrix Assisted Laser Desorption/Ionization." The sample for MALDI is uniformly mixed in a large quantity of matrix. The matrix absorbs the ultraviolet light (nitrogen laser light, wavelength 337 nm) and converts it to heat energy. A small part of the matrix (down to 100 nm from the top outer surface of the Analyte in the diagram) heats rapidly (in several nano seconds) and is vaporized, together with the sample.
-
product
Relative humidity, temperature sensors
T3111
Relative humidity, temperature sensors at probe on 1 meter cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy.
-
product
Temperature, Humidity, Bar. Pressure Transmitter
T7411-4
Humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Built-in pressure sensor.
-
product
Smartphone Thermal Cameras
Smartphone thermal cameras are small sized and light weight in design, converting your mobile devices into a professional portable infrared thermal imager. A user friendly Mobile App is also included for image viewing, download, and analysis.
-
product
Signal Converters For Adapting Encoder Signals To The Interface
The signal converters from HEIDENHAIN improve compatibility with the subsequent electronics by adapting the encoder signals to the interface. Signals can be interpolated, and different designs can be selected for greater flexibility in the application.
-
product
Frequency Converter Characterization With Wideband Modulated Signal
N5245BQ
The N5245BQ provides the N5245B 50 GHz PNA-X network analyzer, application software and accessories for frequency converter measurements with modulated signal such as EVM, NPR and ACPR in addition to gain, gain compression, IMD and other measurements
-
product
Ethernet To GPIB Instrument Interfaces
ICS's 9055 and 8055 Ethernet to GPIB Instrument Interfaces convert any GPIB instrument into a VXI-11.3 compatible instrument that does not require special drivers and is compatible with the following operating systems: LINUX, UNIX, SunOS, MAC OS X, HP-UX, IBM-AIX and Windows systems with VISA or an RPC library. ICS's 9055 and 8055 use VXI-11 RPC calls for secure communication with virtually any computer. Easily programmed on a PC by making VISA calls or on a MAC/UNIX/LINUX computer with RPC calls. Special drivers are not required. ICS Electronics is the premier VXI-11 device supplier with 100% VXI-11 compliance in every product. To learn more about the VXI-11 protocol and how it benefits your system, download our new VXI-11 Tutorial or a copy of the VXI-11 Specification.
-
-
product
Data Concentration And Protocol Conversion
Schweitzer Engineering Laboratories, Inc.
Communicate and collect data from IEDs, exchange and convert data between protocols, and execute output logic for real-time control with SEL automation and communications solutions.
