Isolation
-
Product
PCI 8 Reed Relay Output / 8 Isolated Input Digital Interface (3-13V)
8012S
-
The 8012S PCI digital interface provides eight Reed relay outputs (SPST) and eight optically isolated inputs. Reed relays are well suited for low current applications. The relays are normally open, and close when energized.
-
Product
Optically Isolated Measurement System
IsoVu
-
IsoVu offers complete galvanic isolation and is the industry’s first measurement solution capable of accurately resolving high bandwidth, low voltage differential signals in the presence of large common mode voltages. The stand out feature of IsoVu™ is its best in class common mode rejection across the entire bandwidth. Accurate differential measurements rely on a measurement system’s bandwidth, rise time, common mode voltage, common mode rejection capability, and the ability to connect to smaller test points to characterize devices that are shrinking in size and increasing in performance. Despite these requirements, advancements in test and measurement for power testing, EMI testing, ESD testing, and remote measurement capability have been minimal at best and have not kept pace with changing requirements. While differential voltage probes have had modest performance gains in regard to bandwidth, these probes have failed to make any substantial improvements in regard to common mode rejection, and connectivity. IsoVu is a leap forward in technology and is the only solution with the required combination of high bandwidth, high common mode voltage, and high common mode rejection to enable these differential measurements.
-
Product
64 Channel Isolated Digital Input/Interrupt/Output Module
DP-VME-3636
-
DP-VME-3636 is a 64-Channel Isolated Digital Input/Interupt/Output Module. This module provides 32 channel digital input and 32 channel digital output with isolation. Channels are divided in 2 groups of 16 channels each and are routed to rear I/O. 16 non-isolated TTL channels are available.The module is used for digital interface, status setting, status monitoring, automatic test equipment, and high density industrial automation.
-
Product
Circulator And Isolator
-
A circulator is a three-port passive RF device that directs signals to flow in a single direction, like a one-way street for radio frequencies. An isolator is a type of circulator with one port terminated in a matched load, effectively acting as a two-port device that only allows signals to pass through in one direction and protects components by dissipating any reflected signal.
-
Product
12-bit, 200KHz, 8SE/4DIFF Isolated AI, 4 12-bit AO, 8 Optically Isolated Dig. I/O, 24V, 24 TTL I/O
APCI-3110-8
-
The APCI-3110 is a 12-bit multifunction board for 3.3 V and 5 V PCI systems, with optical isolation up to 1000 V and a high throughput rate of 200 kHz. The PCI board has additional types of conversion: Sequence RAM, Auto Refresh, scan, timer or external event.Furthermore, the board has a PCI DMA, 2 watchdogs, 4 digital inputs and 4 digital outputs. Sensors, which allow to supply current signals instead of voltage signals, also can be acquired with the APCI-3110, as this board offers up to 16 current inputs. The board is protected against overvoltage and input filter and it is protected against high frequency emmission. With the free calibration tool you can do the fine adjustment on-site.
-
Product
PCI Bus Analog Output Board, 4 Isolated Outputs, 14 Bit
APCI-3501-4
-
4 analog output channels Optical isolation 500 V Settling time 30 µs typ. 14-bit resolution (13 bit for 0-10 V) Output voltage: ±10 V, 0-10 V (switchable through software) Output voltage after reset: 0 V Each output channel has its own ground line (without optical isolation from the others) Driver capacity: 5 mA/500 pF Short-circuit protection, EMI filters Noise neutralization of the PC supply Creeping distance: 3.2 mm acc. to DIN VDE 0411-100 Watchdog for resetting the analog output channels (4 different time units: µs, ms, s, min) or as 12-bit timer (with interrupt possibility), when the watchdog function is not necessary2 digital input channels, 24 V, isolated 2 digital output channels, 24 V, isolated Noise immunity Test level: ESD: 4 kV Fields: 10 V/m Burst: 4 kV Cond. radio interferences: 10 V
-
Product
Digital Input Board, 32 Isolated Channels, 24V
APCI-1032
-
32 digital inputs, 24 V or 5 V, incl. 16 interruptible inputs Optical isolation 1000 V Input filters Protection against pole reversal
-
Product
DC Blocking Power Splitter Combiner
PD5140
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.4 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.10 : 1 avg)50 VDC maximum on DC block portsTri Alloy SMA Female (Jack) 50 Ohm
-
Product
PXI 8x9 RF Matrix 250MHz 75 SMB
40-725-751
-
The 40-725 is an 8x9 RF Matrix Module suitable for switching frequencies up to 500MHz (50Ω version). The 40-725 is available in either 50Ω or 75Ω versions with SMB coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connections, these disconnect the matrix from the external test fixture maximizing isolation and RF performance.
-
Product
32-CH Isolated DI & 32-CH Isolated DO PCIe Card with High Input Range
PCIe-7432
-
ADLINK PCIe-7432 is a 32CH Isolated DI & 32CH Isolated DO PCIe Card, featuring robust 2,500V isolation protection, suitable for most industrial applications. Input range up to 24V makes it easy to acquire status of external devices (PCIe-7432HIR output range is from 5 to 35V), making it suitable for relay driving and industrial automation applications. Also provided are two easily configurable interrupt sources on digital input channels.
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, Simplified Current Sink, 750 V Isolation
41-752A-912
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
32-Ch Isolated Digital Output PCI Card
PCI-1734
-
ISA-Compatible with PCL-73432-ch Isolated digital outputHigh output driving capacityD-type connector for isolated output channelsHigh-voltage isolation on output channels
-
Product
Oscilloscope - 1.5 GHz, 4 Analog Channels
DSOX4154A
-
1.5 GHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing at any time
-
Product
High Voltage Isolation Test Systems
HT 9460 and 9464
-
Accurate and non-destructive production testing of ac Isolation Voltage and Partial Discharge.With over 450 systems installed worldwide the 946X series of test systems are the standard and system of choice used by the majority of semiconductor manufacturers that produce optically isolated devices.
-
Product
Static Frequency Converter Systems with Built-in Isolation System
FC3X Series
-
- VFI independent output as per IEC62040- User friendly controls and indications- Compact design with inbuilt transformer- Rugged and field proven for Industrial and Defence application- Ultra light weight- Higher efficiency of operation means significantly lower running costs- State of the art IGBT based PWM technology, to increase crest factor tolerance & dynamic stability- Continuously delivers full output power at ambient as high as 45ºC- Can feed upto 400% rated current for half cycle- Very high MTBF
-
Product
ISDD Tool Suite
-
The Integrated System Diagnostic Design or ISDD Tool Suite provides a start to finish solution for meeting all the diagnostic needs of system design. The ISDD design process is centered around functional modeling of systems which is used to develop the diagnostics and failure analysis necessary to fully support good system design. This includes: *Analysis of Fault Detection and Fault Isolation.*Analysis of critical failures and their impact upon safety.*Detecting and reducing false alarms caused by diagnostics.*The impact of prognostics upon fault detection/fault isolation and mitigation of critical failures.*Development of vehicle health management and troubleshooting diagnostics
-
Product
CIRCUIT ENERGIZER
TH852
-
*Can be used with most 12V mini jump starters with the standard EC5 port*Allows for more portability and freedom from long battery wires*Factory correct terminals means less of a need to back probe*Isolates component from the rest of the circuit which results in less damage to entire wiring/computer modules*No need to remove component for bench test
-
Product
BaseMate Equipment Platforms
Series 9300
-
The BaseMate Series 9300 Isolation Platforms for large equipment offer you maximum flexibility and choice.With over 16 time-tested modular configurations you’re sure to get the optimum configuration to meet your application needs. BaseMate Platform Systems provide vibration isolation benefits that are unmatched by other floor systems.
-
Product
Standard Signal Loop-Powered
-
Knick Elektronische Messgeräte GmbH & Co. KG.
Isolation and 1: 1 transmission of 0/4 ... 20 mA current signals without additional auxiliary power. Also for use in hazardous areas. Particularly high reliability and certified functional safety up to SIL 3 / PLe.
-
Product
Programmable Power Supplies
GENESYS+™ Rack DC Power Systems
-
The GENESYS+™ High Power Programmable Rack DC Power System platform provides advanced features in a light-weight portable high power density profile with a comprehensive set of built-in user-friendly interfaces that include a multi-functional front panel, LAN (LXI 1.5), USB (2.0), RS-232/RS-485 and Isolated Analog (5V/10V) along with several optional digital communication interfaces (IEEE, EtherCAT or Modbus-TCP).
-
Product
Isolated RS-232
-
Analog Devices offers a wide range of RS-232 transceivers to suit many applications. As RS-232 cable networks and the systems to them can be vulnerable to voltage spikes and ground loops, we have developed a number of innovations that protect against these issues and create an isolated RS-232 environment. We accomplish this through our isoPower® integrated dc-to-dc converters, as well as our iCoupler® technology, which enable the power isolation and signal isolation required for system reliability in a noisy environment.
-
Product
PCIe-8433, PCI Express, 2-Port, Isolated, RS485/RS422 Serial Interface Device
781745-01
-
The PCIe‑8433/2 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
-
Product
sbRIO-9269, Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module
781120-01
-
Non-Enclosed, 100 kS/s/ch Simultaneous, ±10 V, Isolated, 4-Channel C Series Voltage Output Module - The sbRIO‑9269 is a channel‑to‑channel isolated analog output module. The sbRIO‑9269 adds channel‑to‑channel isolation for increased safety and improved signal quality. Channel‑to‑channel isolation is commonly needed for applications that have multiple electrical systems, such as automotive tests, or industrial applications that are subjected to increased noise and often contain multiple ground planes. Non-enclosed modules are designed for OEM applications.
-
Product
PCIe Digital I/O Board, 32 Optically Isolated I/O Channels, 24V
APCIE-1532
-
16 digital inputs, 24 V, isolated16 interruptible inputs16 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-8
-
18-bit resolution, unipolar, 16-bit accuracy 8 differential inputs for strain gauges Voltage range 0 to + 2.5 V 8 independant voltage sources for the connected pressure sensors Output voltage for the voltage sources 5 V, 40 mA Gain and offset calibration Calculation of the pressure value through software Programmable gain 16-bit accuracy with sample rates of 20, 40, 80 or 160 Hz 4 digital input channels, 24 V and 3 digital output channels, Open Collector, isolated
-
Product
Oscilloscope - 500 MHz, 2 Analog Channels
DSOX3052T
-
500 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
DC Earth Leakage Current Measurement
DCZCT-11M
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*DC Earth Leakage Current Measurement *Bipolar DC ±12V Power Supply*Output DC ±1.5V at DC 10mA *Isolated Housing Case based on UL94V-0*Through Hole PCB Mount Type, Exciting Current Method
-
Product
PXI Expandable 16x16 RF Matrix 75Ohm 1.0/2.3
45-720A-741
-
The 45-720A module is a 6U 16x16 RF Matrix suitable for switching frequencies to beyond 250MHz. The 45- 720A module is available in 50 and 75 Ohm versions with a choice of coaxial connectors. It is intended for the easy construction of high performance bidirectional matrix switching systems. Automatic Isolation Switches are located on all coaxial connectors, these disconnect the matrix from the external test fixture. This maximises isolation and RF performance.
-
Product
USB / RS232 / RS485 / RS422 Opto Isolators
-
USB has now moved from the desktop to more challenging environments, including instrumentation, point of sales, factory & building automation, etc. With our rugged, industrial-grade USB isolators and USB to RS232 / RS485 / RS422 optically-isolated converters, we ensure that your assets are well protected from unexpected events.
-
Product
Ultra Fast Flexible Implantable Microprobe
IT-23
-
IT-23 Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Time constant 0.005 seconds. Tissue Implantable with a 23 gauge needle (supplied). Fairly fragile. Sensor wires are twisted TFE Teflon™ insulated. Maximum Temperature 150°C. Isolated. Probe diameter .011", 3 foot lead.
