Isolation
-
Product
Reservoir Isolators
-
Fluid contamination can lead to high maintenance costs and downtime in hydraulic systems. Parker reservoir isolators provide protection against the ingestion of airborne contaminants such as dust, chemicals and water vapor through the breather-vent of your hydraulic system. Utilizing an elastomer bladder as a lung, the changes in gas volume in a hydraulic system's reservoir can be trapped and prevented from mixing with the outside atmosphere. Unlike conventional breather-vent filters, Parker reservoir isolators provide a positive separation without the possibility of clogging or need for maintenance.
-
Product
Isolated Serial Communication Card
PCI-ICM-1S
-
The PCI-ICM-1S is a single port asynchronous optically isolated serial communication card that can be installed in any 3.3V or 5V PCI slot computer. Data lines are opto-isolated from the computer and from each other to assure communication even when large common mode voltages and noise are imposed.
-
Product
Mixed Signal Oscilloscope - 100 MHz, 4 Analog Plus 16 Digital Channels
MSOX3014T
-
100 MHz4 analog plus 16 digital channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
GPS Signal Splitter 16 Way, SMA Jack, 1 - 2 GHz, 50 Ohm Coaxial
GPS161
-
INSTOCK Wireless Components, Inc
Wideband Frequency (1000-2000 MHz)Low Insertion Loss (0.6 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)15 VDC & 75 mA Max on DC Block PortsTri Alloy SMA Female (Jack) Low PIM
-
Product
PCI/PCIe-Based Serial Communications Cards
PCI-C588/PCI-C584/PCIe-C588
-
- IRQ & IO address automatically assigned by BIOS- Supports up to 2 cards per system, jumper-less, easy to configure- Isolated RS-422/RS-485 interface (C422/C485, C518/C514)- PCI Rev 2.1 Plug-and-play- PCI Express® x1 compliant (PCIe-C588)
-
Product
PXI Isolated Millivolt Thermocouple Simulator - 8 Channel
41-761-004
-
The use of two wire outputs and isolation from ground ensures that the 41-761 can be used to accurately simulate low voltages even in the presence of common mode voltages in the system. Each Vcold connection is independent permitting the 41-761 to be connected to multiple cold junctions.
-
Product
Acquisition Of Strain Gauges, Isolated, 18-bit
APCI-3300-4
-
4 channels for the acquisition of strain gauges. 4 onboard voltage sources. 18-bit resolution. Optical isolation 1000 V. Software linearisation. Direct connection of the pressure sensors with terminal board PX3200
-
Product
Oscilloscope - 500 MHz, 4 Analog Channels
DSOX4054A
-
500 MHz4 analog channels Easily view signals on the large 12.1-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering Capture more data with 4 Mpts memory and standard segmented memory See more signal detail with 1,000,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, dual-ch 20 MHz arbitrary Wave Gen, 3-digit DVM, serial trigger and analysis & mask testing
-
Product
High Voltage Isolator for Logic Analyzers
LX-08
-
The LX-08 series of high voltage logic analyzer adapters provides a safe isolated method of measuring high voltage control signals with a low voltage logic analyzer. All inbound signals are optically isolated and attenuated to a safe level for the delicate inputs typically found on logic analyzers. The inputs on the LX-08 are capable of withstanding voltages up to +/- 300V AC/DC, higher voltage configurations are available upon request. Rather than probing with multiple neon screwdrivers, the LX-08 can provide simultaneous viewing of up to 8 circuits in the STANDALONE mode via the indicator array. Need to catch a transient event or map out a timing sequence? Just add a logic analyzer to the outputs of the LX-08 and turn it into a high voltage logic analyzer. High voltage signals that were hazardous for a logic analyzer can now be measured safely. Typical outputs of a high speed PLC sequencer can be precisely timed and measured from both sides of the control relay. With the built in user selectable AC filter circuit, an AC signal can be measured as DC events or AC cycles.
-
Product
Adapter/Nickel
WADP-NFSM
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
8-Ch Relay And 8-Ch Isolated Digital Input PCIE Card
PCIE-1760
-
8 opto-isolated digital input channels with counter/timer function8 relay actuator output channels2 opto-isolated PWM outputsProgrammable digital filter function for DIJumper selectable dry contact/wet contact input signalsUp event counters for DILED indicators to show activated relaysPattern match interrupt function for DIChange of state interrupt function for DIBoardID switch
-
Product
15-CH Isolated Digital Input Module
ND-6054
-
- Channels: 15- Isolation Voltage: 5000 VRMS- Switching Level: with 24 V common power. Low (0): 22 V min.; High (1): 0-22 V- Programmable input polarity
-
Product
RS-232 to RS-485 Optically Isolated Interface Converter
Model 8322
-
FEATURES: 4 Wire-Master/Slave Operation; Active Mode Control Via RTS or Data; Opto Isolation; Built-in Power Supply; Internal Microcontroller; 38.4 KBPS Data Rate; DIN Rail Mountable; Programmable Terminations. The Model 8322 RS-232 to RS-485 Interface Converter allows information exchange in half duplex mode over two twisted pairs.
-
Product
Rectal Probe For Mice
RET-3
-
• Smooth ball tip. Stainless steel shaft - 3/4'' long, .028'' diameter. Tip diameter .065'', 5 foot lead length. Time constant 0.5 seconds. Not Isolated
-
Product
64-CH Isolated Digital I/O PCI Cards
PCI-7432/7433/7434
-
ADLINK's cPCI/PCI-743X series cards are 64-CH high-density digital input and/or output cards that provide a robust 2,500 V isolation protection and are suitable for most industrial applications. The wide input range of the cPCI/PCI-7432 and cPCI/PCI-7433 makes it easy to sense the status of external devices. There are several options for PCI-743X series, such as normal version with input range from 0 to 24 V, as well as HIR version with high input range from 0 to 50 V. The PCI- 7433ALC is specifically designed for AC power test system.
-
Product
Manual Step Attenuator
WATT-3SM352
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customers demand. All Warisons products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Analog Only Oscilloscopes
-
Isolated Signal Generator (0-65MHz, Sine Wave Only) for serial numbers above 4000. The CS701 is rated at 300V RMS isolation (class III), and offers output levels from 1 mVp-p to 7 V p-p. You can use the CS701 for Power Supply FRA without needing an isolation injection transformer.
-
Product
Flexible Implantable Microprobe
IT-1E
-
IT-1E Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Similar to our most popular IT-18 microprobe but the sensor bead is exposed, resulting in the same ultra-fast response time of the IT-23 but with the Teflon™ sheath strength of the IT-18. Time constant 0.005 seconds. Tissue Implantable with a 18 gauge needle (supplied). Rather fragile at tip. Coated in Teflon™. Maximum Temperature 150°C. Isolated. Probe tip diameter .011", sheath diameter .025'' . 3 foot lead.
-
Product
USB HD-SDI Video Processor/Capture Card with Overlay
2246
-
Video overlay up to full screen at up to 1920x1080 SDI (HD/SD) and analog inputs DVI, SDI (HD/SD), and analog outputs Prescaled SD A/V compression engine with MPEG-1/2/4 output Up/downscaling on DVI and analog outputs Captures uncompressed HD/SD frames Generates "freeze frame" video from captured frames Video "zoom" on MPEG stream and DVI output Isolated general-purpose digital I/O: 8 in / 4 out USB 2.0 interface
-
Product
Flexible Implantable Microprobe
IT-18
-
IT-18 Flexible Implantable Microprobe - Implantable in semi-solids and tissue with 18 gauge needle (supplied). Also for immersion in various solutions and rectal temperatures of small animals. Totally sheathed in chemical resistant Teflon™. Quited rugged. Maximum Temperature 150°C . Isolated. Probe diameter .050" (14 gauge represents the needle gauge that the probe can be inserted through). Time constant 0.3 seconds.
-
Product
Oscilloscope - 200 MHz, 2 Analog Channels
DSOX3022T
-
200 MHz2 analog channels Easily view and analyze your signals with on the large 8.5-inch capacitive touch screen Isolate signals in seconds with exclusive Zone touch triggering See more signal detail with the 1,000,000 wfms/s update rate Capture more data with up to 4 Mpts memory Expand your measurement capabilities with full upgradability: Add bandwidth, digital channels, 20 MHz arbitrary waveform generator, 3-digit voltmeter, serial trigger and analysis & mask testing at any time
-
Product
3-Ch RTD Input Module
ADAM-5013
-
Accuracy: ±0.1% or betterEffective resolution: 16-bitInput connections: 2, 3 or 4 wireSampling rate: 10 samples/sec. (total)Isolation voltage: 3000 VDCInput type: PT100 or Ni RTDChannels: 3
-
Product
PCIe Digital I/O Board, 64 Optically Isolated I/O Channels, 24V
APCIE-1564
-
32 digital inputs, 24 V, isolated16 interruptible inputs32 digital outputs, 24 V, isolated, 10 to 36 V, 500 mA/channelOptical isolation 1000 VWatchdog for resetting the outputs to "0" (when Power-On)Protection against fast transients, overvoltage, electrostatic discharge and high-frequency EMIInputs: voltage reversal, input filtersOutputs protected against short circuitOvertemperature and overvoltage protectionDiagnostic report in case of short circuits, overtemperature, voltage drop ...24 V power outputs with protection diodesShutdown logic when the external supply voltage drops below 5 V
-
Product
PXI/PXIe Battery Simulator Module, 4-Channel, V/I Readback, 750 V Isolation
43-752A-012
-
Targeting EV, automotive, aerospace, energy storage and electric aircraft applications, the new battery simulator modules occupy a single PXI slot. These 4-channel battery simulators are capable of supplying up to 7 V and 300 mA per channel. The channels are fully isolated from ground and from each other, allowing series connection to simulate batteries in a stacked architecture.
-
Product
RF Power Splitter, Combiner, Divider P67, 2 Way, SMA Female, 2.4 - 6.0 GHz
PD2558
-
INSTOCK Wireless Components, Inc
Wideband Frequency (2.4 - 6.0 GHz)Low Insertion Loss (0.3 dB avg)High Port to Port Isolation (25 dB avg)Excellent VSWR (1.15 : 1 avg)Outdoor Weatherproof ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
Contact Resistance Meter
CRM 100C
-
CRM 100C directly measures resistance values with DC current injection under live switchyard conditions.The CRM 100C is specially designed to reliably measure contact resistance of Circuit Breakers, Isolators, Bus Bar joints, welded joints etc., under the hostile electrostatic noise found in live EHV switchyards. It can also be used for testing cables, graphite bars etc.
-
Product
RF Power Splitter, Combiner, Divider RoHS, 6 Way, SMA Female, 698 - 2700 MHz, 50 Ohms
PD2160
-
INSTOCK Wireless Components, Inc
Wideband Frequency (698 - 2700 MHz)Low Insertion Loss (0.5 dB avg)High Port to Port Isolation (30 dB avg)Excellent VSWR (1.15 : 1 avg)RoHS Compliant Splitter ConstructionTri Alloy SMA Female (Jack) Low PIM
-
Product
Adapter/Stainless Steel
WADP-29F29F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
32-CH Isolated DIO PCI Cards
PCI-7230/33/34
-
ADLINK"s PCI-723X series are 32-CH isolated input and/or output cards which provide a 2,500 V optical isolation protection. The wide input range of the PCI-7230 and PCI-7233 makes it easy to sense the status of external devices. The non-polarity characteristic is suitable for a wide variety of industry applications. The PCI-7230 and PCI-7234 devices also feature a wide output range from 5 to 35 V, which is suitable for relay driving and industrial automation applications. The PCI-7234P provides current-source output capability. The PCI-7230 and PCI-7233 also provide two interrupt sources on digital input channels. The PCI-7233 also features a change-of-state (COS) function that generates an interrupt when any digital input changes its state.
-
Product
1.3W to 30W - Single Output / Multiple Output
CCG Series
-
*Space Saving Package Sizes*4.5-18V, 9-36 Vdc or 18-76 Vdc Inputs*3.3, 5, 12, 15, 24, 30, ±12, ±15 Vdc Outputs*1500 Vdc Isolation*-40 up to 110 °C Case Temperature*Six-Sided Shielding (CCG15-30)*Through-hole and SMT terminations (CCG1R5-3)
