Timing
See Also: Time, Timers, Time Interval, GPS Time, Time Reference, Time Code, Time Domain, Time Standards, Time Interval Analyzers
-
Product
Soil Heat Flux Sensors
-
Soil heat flux sensors may consist of several thermocouples whose measurements are averaged, a single thermopile, or a single thermopile with a film heater. These sensors measure the rate of energy transferred through a surface. Data regarding the amount of energy stored in soil as a function of time is used in energy-balance and Bowen-ratio flux systems.
-
Product
Discharge Units
-
ENTES Discharge Units are used in capacitor banks and provide quick discharge over short periods of time.
-
Product
Vacuum and Fuel Pump Tester
DVG1
-
Suitable for testing and fault finding the following in petrol engines including: Spark misfires; poor engine compression; weak/rich mixture; ignition over advanced/retarded; inlet manifold and carburettor air leaks; incorrect valve timing; poor fuel economy; balancing carburettors; turbo boost gauge; fuel pump testingDisplay packed.
-
Product
SP3T RF Pin Diode Switches To 18 GHz
-
Pulsar Microwave manufactures 3-way absorptive and reflective switches for use in 50-ohm systems. These SP3T switches operate from 100 MHz to 18 GHz and handle 200 mW input power. VSWR performance is often 1.6:1 or better with 100 ns switching time. Minimum isolation of 60 dB is specified for most units. Absorptive and reflective switches require +5V and -5V power supply to function. Control logic is from 0 to +5 volts. All voltage and ground connections are made by feed thru and turret terminals, respectively.
-
Product
IRIG Timecode Receiver and Generator
RG1
Receiver
The RG1 Time Code receiver synchronizes to IRIG-A/B/G time codes and provides precise time in a memory register, for the host SBC.The IRIG output of the card can be used to synchronize other IRIG time code readers. Additionally, the RG1 includes a real-time clock (RTC) that may be used as a reference source for IRIG master applications, to free the system processor from the task of updating the master timer.
-
Product
PXI 3A Power MUX BRIC, 2-Channel, 24-Pole
40-571-101
Multiplexer Module
The 40-571 is a Power Multiplexer designed to simplify the connection of a common set of test equipment to one of a number of different devices for testing (simultaneous multiple channel selection is possible for most configurations, see switching specifications for restrictions). It is ideal for applications where the equipment needs to conduct the same test process on a series of similar devices one at a time. It is available in a variety of configurations that allow testing with differing number of devices to be tested and different connection widths to suit differing test equipment pin counts.
-
Product
GPIB to Parallel Printer Interface
Model 4892B
-
* Adds a GPIB Interface to Printers with Centronics or IEEE-1284 parallel interfaces. See the compatible printer list. * Replaces obsolete printers and plotters with a current HPGL/PCL5 printer.* Prints and Plots from most Analyzers. * Large 256 kbyte buffer and high speed GPIB interface off-loads the instrument and reduces printing time.* No program changes required.* Rack mountable in 1 U high rack mount kit.* Includes universal VAC Power Adapter and printer cable.
-
Product
Lightweight Vehicle Surveillance System
LVSS
-
The skid-based LVSS converts a standard commercial pickup into a rapidly deployable command and control center. Within minutes, a single operator can set up the LVSS and report for full perimeter duty from the comfort of the cab. When it’s time to relocate, the mast and its mounted FLIR cameras, radar, and sensors, stow out of sight for covert transportation.
-
Product
Programmable DC Electronic Load
63000 Series
-
The 63000 Series programmable DC electronic loads are reliable, precision instruments primarily designed to test switching power suppl ies, A/D power suppl ies, power electronic components, adapters, 3C batteries and chargers. Its maximum 350W rated power makes it suitable for testing numerous types of lower power devices. The 63000 Series offers models in two operating voltages 150V models, with 250W and 350W power levels up to 60A in a single unit. Their compact and light weight design make these loads easy to move around which is ideal for R&D and design validation. Each model of the 63000 Series has unique user-def ined waveform (UDW) funct ion capable of simulating real-world custom waveforms. In addition, a data storage function has been built in for saving and recalling up to 100 stored settings at any time. For automated testing, these save and recall functions can save a great deal of time. The 63000 Series has 3 power ranges that can precisely measure the voltage and current in real time. Since short circuit testing is a critical test item, the 63000 provides short circuit simulation to effectively address application demands for power and automated testing.
-
Product
Spectrometer
XFFTS
-
This spectrometer is a control chassis which accomodate 8 FFTS cards, each with up to 2.5 GHz bandwidth. Each XFFTS-board operates from a single 5 Volt source and dissipates less than 30 Watt, depending on the actual configuration in terms of bandwidth and number of spectral channels. Precise time stamping of the processed spectra is realized by an on-board GPS/IRIG-B time decoder. Furthermore, the 10-layer boards include a programmable ADC clock synthesizer for a wide range of configurations (bandwidth: 0.1 – 2.5 GHz), making the spectrometer flexible for different observation requirements .
-
Product
Multi-Channel 1553 Interface for PCI Express 4 Lane Systems
PCIE4L-1553
Interface Card
Alta Data Technologies’ PCIE4L-1553 interface module is a multi-channel (1-4), ½ size, 4 Lane PCI Express 1553 card supported by the latest software technologies. The PCI Express card is based on the industry’s most advanced 32-bit 1553 FPGA protocol engine, AltaCore™, and by a feature-rich application programming interface, AltaAPI™, which is a multi-layer ANSI C and Windows .NET (MSVS 2005/08/10 C++, C#, VB .NET) architecture. This hardware and software package provides increased system performance and reduces integration time.
-
Product
PXI Semiconductor/IC Test System
Test System
A high-density 100MHz PXIe digital IO card designed for characterizing, validating, and testing a variety of digital and mixed-signal ICs. Each IO card consists of a Sequencer Pattern Generator (SQPG) and 32 channels of full ATE-like features. The 33010 IO card is expandable up to 256 channels. Some unique features of the 33010 include an on-board SQPG, per pin timing/levels/ PMU/TFMU, multiple time domains, and multithreaded testing for complex IC testing. Each channel is also equipped with 64M vector memory, 16 timing sets with on-the-fly timing change, and per pin timing and frequency measurements up to 400 MHz.
-
Product
Solar Array Simulator
G5.SAS
-
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Product
FLIM Upgrades for Nikon
A1 / C1 / C2
-
*bh FLIM Embedded in Nikon NIS-Elements Software*Two Fully Parallel TCSPC FLIM Channels*Compact bh Simple-Tau or Power-Tau System*Two HPM-100-40 GaAsP Hybrid Detectors*Excitation by bh ps Diode Lasers*Excellent Time Resolution: Electrical IRF Width 6.5 ps FWHM*Excellent Timing Stability*Time Channel Width Down to 813 fs*Megapixel FLIM, Up to 2048 x 2048 Pixels at 256 Time Channels*Detection Wavelength Range from 360 nm to 700 nm
-
Product
MCB Instantaneous Trip Test Bench
-
The SCR Elektroniks MCB Instantaneous Trip Test Bench is designed for Testing of MCB to carry out “Test of Instantaneous Tripping and of correct opening of the Contacts” as per IEC: 60898-1:2002 Clause 9.10.2 at rated voltage. This test is carried out with power factor between 0.95 and 1 with the sequence operation being O-t-CO-t-CO-t-CO with timings as specified in 9.12.11.1.
-
Product
PXIe-6368, 16 AI (16-Bit, 2 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module
781058-01
Multifunction I/O
PXIe, 16 AI (16-Bit, 2 MS/s/ch), 4 AO, 48 DIO, PXI Multifunction I/O Module—The PXIe‑6368 is a simultaneous sampling, multifunction DAQ device. It offers analog I/O, digital I/O, four 32‑bit counters, and analog and digital triggering. Onboard NI‑STC3 timing and synchronization technology delivers advanced timing functionality, including independent analog and digital timing engines and retriggerable measurement tasks. The PXIe‑6368 is ideal for a variety of applications, such as IF digitization; transient recording; ISDN, ADSL, and POTS manufacturing test in the telecom industry; ultrasound and sonar testing; and high-energy physics. The included NI‑DAQmx driver and configuration utility simplify configuration and measurements.
-
Product
Spinstand Automation for Media Testing
V2002
-
The spinstand V2002 with the media-testing automation loads and unloads the cap of the vacuum chuck1 and moves the disk stabilizer shroud on and off media without operator’s intervention. As a result, less time is required for a media replacement, so the same number of disks can be tested faster.
-
Product
Static Pressure Manometer Kit
EM201SPKIT
-
UEi Test & Measurement Instruments
A digital, time saving electronic manometer static pressure kit
-
Product
Signature Surge Testers
TS Model
-
Although all PJ Surge Testers are capable of testing 3 Phase Motors, this "TS" Model has the same characteristics as the Signature Model (rack-mounted, Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope) but includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
Product
Digital to Resolver
HDR
ITA
Computer Conversions Corporation
The HDR Series are sub-miniature modules that are; size comparable, low cost alternatives to Hybrid type D-R and D-S converters. Because of their advanced modular design the HDRL series features short lead times that are neither limited to infrequent hybrid production cycles, long term parts allocation, minimum quantity purchases, or hybrid obsolescence related concerns.
-
Product
Guided Wave Radar Level Transmitter
2291
-
The 2291 Guided Wave Radar level transmitter is designed for continuous level measuring of conductive or non-conductive liquids, pulps and solids. The 2291 level gauge operates based on the well-known TDR (Time Domain Reflectometry) principle. Micropulses are sent along a probe guide at the speed of light. As soon as the impulse reaches the surface of the medium, it is reflected back to the electronic module. Level distance is directly proportional to the flight time of the impulse.
-
Product
High Impedance Active Probes
18C & 19C
-
High impedance probes, PICOPROBE® MODEL 18C and MODEL 19C, combine the most advanced MOS and bipolar technologies with special, low capacitance packaging techniques to achieve truly remarkable electronic measurement capabilities. While being manufactured each instrument is individually optimized for the best possible performance. The extremely low input capacitance, high input impedance, and almost negligible input leakage current permits the direct probing of even the most sensitive MOS dynamic nodes. At the same time, the full dc capability of this Picoprobe coupled with the high speed capability permits the full characterization of circuits.
-
Product
PXIe-5763, 16-Bit, 500 MS/s, 4-Channel PXI FlexRIO Digitizer
785164-01
FlexRio Digitizer
The PXIe-5763 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 500 MS/s with 16 bits of resolution and features 225 MHz of analog input bandwidth. With over 73 dB of SNR, the PXIe-5763 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5763 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Tube-To-Tube Gravity Handler
Rasco SO1000
-
The SO1000 test handler’s mature design and high reliability it provides excellent cost of test. Highly flexible as a result of a broad range of device kits can be combined with various Sensor and MEMS applications.Featuring a fast plunger with up to four plunger heads for high speed and high throughput with index time down to 500 ms. Available in single, dual, and quad configurations.
-
Product
Digital Multimeters
-
Shenzhen Everbest Machinery Industry Co.,Ltd.
Heavy duty True RMS Industrial Digital Multimeter with TFT color LCD display,providing fast A/D converting sampling time, high accuracy, built-in datalogging and TrendCapture featuresIt can trace any interrupted problems of the equipments and watch on without personIt is easy to find and solve the problems of the production equipment, providing Bluetooth technology and memory the datasheetsIt is safer measurements with double molded plastic housing design
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Product
9GS/s 8Bit, 4GS Mem 2CH 8 Markers AWG
P9082D
Waveform Generator
The Proteus P9082D, is a 9GS/s, dual channel arbitrary waveform generator packaged in a 4U, half 19” dedicated chassis, offering technologically advanced options and configurations that integrate the ability to transmit, receive and perform digital signal processing all in a single instrument. The P9082D offers industry leading performance Including an innovative task oriented programming, real time data streaming, fast feedback loop for environment dependent waveform generation and user customizable FPGA for application specific solutions.
-
Product
Serial FPDP Extreme 1/2 ATR Recorder
Talon RTX 2596
-
- Rugged 1/2 ATR MIL-spec chassis for harsh mechanical and thermal environments- Environmentally sealed, conduction-cooled- Fully sealed for RF emissions with EMI power line filter- MIL-STD circular connectors- Compact and lightweight design - 18 lb (8 kg)- QuickPac® drive packs allow quick removal of all data storage up to 61 TB via the front panel- Ideal for UAVs, military vehicles, aircraft pods and outdoor environments- Four-channel Serial FPDP record/playback- Supports Flow Control, CRC, and Copy/Loop Mode as a receiver and transmitter- Supports 1.0625, 2.125, 2.5, 3.125 and 4.25 GBaud link rates- Single-mode and multi-mode fiber interfaces available- Sustained real-time record rates up to 4 GB/s- 12 to 28 VDC power supply- Optional GPS receiver for precise time and position stamping- SystemFlow API, GUI and Signal Viewer analysis tools- Optional telnet remote connection to recorder
-
Product
CompactPCI Card
IIB-429-CPCI
-
The IIB-429-CPCI provides from ARINC-429 compatible channels (2 receive and 2 transmit) at any rate between 12.5 and 100 kbps. Because the IIB-429-CPCI is built upon a flexible platform, user function can be implemented almost without restriction, making this product flexible and user-friendly. This CompactPCI card has a 3U form factor. This unit is also available in a 6U form factor (IIB-429-CPCI-4C) with four times the functionality
-
Product
Frequency Counter Series
FCA3000/3100
-
Offering up to 20 GHz measurements, the Tektronix FCA3000 and FCA3100 Frequency Counter Series pack many different functions into one feature-rich instrument. With unprecedented resolution, you can capture very small frequency and time changes. And with the industry's most comprehensive analysis modes, including measurement statistics, histograms, and trend plots, you have the tools you need to quickly and accurately analyze your signal.
