cPCI Digitizer
-
Product
4-CH 16-Bit 10/40 MS/s PCI Digitizers with 512 MB Memory
PCI-9816/9846
Digitizer
The ADLINK PCI-9816/9846 are 10MS/s, 40MS/s sampling 16-bit 4-CH digitizers designed for digitizing high frequency and wide dynamic range signals with an input frequency up to 20 MHz. The analog input range can be programmed via software to ±1 V or ±0.2 V and ±5 V or ±1 V. With a deep onboard acquisition memory up to 512 MB, the PCI-9816/PCI-9846 are not limited by the data transfer rate of the PCI bus to enable the recording of waveforms for extended periods of time.
-
Product
22 Bit / 1 MS/s Waveform Digitizer
WFD22
Waveform Digitizer
The WFD22 is a 22 bit Waveform Digitizer for medium-speed / high resolution waveform capturing and analyzing. It combines superior dynamic performance with a very high DC accuracy.The module features fully differential inputs to reduce common-mode level disturbances. It can also be used in Single Ended mode where an internal DC-offset source sets the midscale level.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 125 MS/s on 8 Channels, 80 MS/s on 16 Channels, 16 Single-Ended Inputs, 8 True Differential Inputs
DN2.596-16
Digitizer
The digitizerNETBOX DN2.59x series allows recording of one, two, four, eight or 16 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
Digital I/O Board
3512
Digital I/O
The 3512 is an eight channel non-isolated digital I/O board with +5V tolerant 74LCX14 inputs with hysteresis and +3.3V CMOS 74LVTH125 driven outputs. Each I/O line features a series 10 ohm damping and protection resistor and a 4.7K pull up resistor to +3.3V. On power up the outputs are tri-stated, and can then be enabled on a bit by bit basis. Output high drive is 32mA @ 2.0V minimum. Output low drive is 32mA @ 0.8V maximum.
-
Product
Ethernet/LXI digitizerNETBOX 16 Bit Multi-purpose Digitizer - 20 MS/s on 32 Channels
DN6.592-32
Digitizer
The digitizerNETBOX DN6.59x series allows recording of up to 48 synchronous channels with sampling rates of 20 MS/s up to 125 MS/s. These products offer outstanding A/D features both in resolution and speed as a remote instrument. The powerful A/D amplifier section offers 6 different input ranges, programmable offset and a software switching from single-ended (full number of input channels) to true differential (half number of input channels).
-
Product
NI-9477, 60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module
780174-01
Digital Module
60 V, 32-Channel (Sinking Output), 8 µs C Series Digital Module - The NI‑9477 works with industrial logic levels and signals to connect directly to a wide array of industrial relays, solenoids, and motors. Each channel is compatible with signals from 5 V to 60 V and … features isolation from channel‑to‑earth ground. You can wire the NI‑9477 channels in parallel to sink up to 20 A of current per module (1 A per channel maximum).
-
Product
Keysight 64-bit Digital I/O with Memory and Counter for 34980A
34950A
Digital I/O Module
The Keysight 34950A module for the 34980A Multifunction Switch/Measure Unit has 64 bi-directional lines configured as eight 8-bit channels. Each 8-bit channel has programmable polarity and thresholds up to 5V. The memory is useful for simulating and capturing digital patterns up to 10 MHz. It provides configurable handshaking protocols for a wide variety of applications.
-
Product
Dynamic D/A Converter, 16-channels, 16-Bit, Unipolar, 30 V/20 mA
M9188A
Digital / Analog Converter
The M9188A is a PXI based, 1-slot unipolar Dynamic DAC which has 16 channels capable of supplying typical waveforms at high voltages. It has 4 isolated banks with 4 channels in each bank.
-
Product
AXIe High-Speed Digitizer/DAQ, 10-bit, 10 GS/s, DC to 2.5 GHz BW
M9710A
Digitizer
Based on the AXIe standard, the M9710A is a unique 10-bit high-speed digitizer, capturing signals from DC up to 2.5 GHz at 5 GS/s. It provides excellent measurement accuracy and high dynamic range across four phase-coherent channels within a single card. Optimized response allows few hundred picoseconds pulse analysis. Moreover, an interleaving option allows acquisition at 10 GS/s on two combined channels, keeping excellent measurement fidelity.
-
Product
Digital Signal Processor
FalconX
Digital Signal Process
The FalconX is a radically new digital signal processor that combines a cutting-edge hardware platform with patented SITORO® signal processing technology, uniting unprecedented technical performance with an innovative “plug & play” design.
-
Product
NI-5762, 250 MS/s, 16-Bit, 100 MHz Bandwidth, 2-Channel Digitizer Adapter Module for FlexRIO
781749-01
Digitizer
The NI‑5762 is a digitizer adapter module that, when combined with a PXI FPGA Module or Controller for FlexRIO, creates a high-speed digitizer that simultaneously samples two channels at 250 MS/s with options for 100 MHz of analog bandwidth or an unfiltered path. You can use the NI‑5762 to do real-time processing and streaming of analog data with high-performance A/D converters. The Digitizer Adapter Module for FlexRIO is ideal for applications that require in-line data processing, high data streaming rates, and deployed high-performance solutions.
-
Product
PXIe Isolated Digitizer, 2-channels, 16-bit, 256 V, 32 Msa/Ch memory
M9217A
Digitizer
The M9217A PXIe digitizer is a single slot, 2 isolated input channels, supporting up to 256 V and sampling rate of 20 MSa/s and 16-bit resolution.
-
Product
PXIe-5764, 16-Bit, 1 GS/s, 4-Channel PXI FlexRIO Digitizer
785166-01
FlexRio Digitizer
The PXIe-5764 is a PXI FlexRIO Digitizer that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PXIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA. Available in AC and DC coupled variants, the PXIe-5764 is ideal for both time and frequency domain applications, including radar prototyping, LIDAR, communications, microscopy, OCT, event detection, and particle physics.
-
Product
Multi-Channel 10-Bit Digitizer
ADQ8-8C
Digitizer
With compact modular form factors, 8 channels per board, and high-precision multi-board synchronization capabilities, ADQ8-8C is ideal for massive multi-channel implementations.
-
Product
Dynamic Digital I/O (3U), 32 Channels Up To 200 MHz W/512MB On-Board Memory, W/LVDS
GX5283
Digital I/O
The GX5280 Series are high performance, cost-effective 3U PXI dynamic digital I/O boards with 32 TTL input or output channels and 32 LVDS input or output channels. The GX5280 Series offers an industry leading 512 MB of on-board memory and supports test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
PXI Digital IO: 32 inputs, 32 outputs, 0.3V to 50V
M9187A
Digital I/O Module
The M9187A has 32 input channels that can be used for comparing inputs to user-defined thresholds between 0.3V and 50V, with 12mV setting resolution. Each input is protected up to 100V. In addition, the 32 output channels use a high current to drive the output high or low, and are capable of sourcing 0.4A from the high side or 0.5A sink from the low side of each channel. These outputs are protected against over-voltage or over-current conditions. Choose from the durable connector block or the standard cable connections.
-
Product
PXI 32 Channel I/O, High and Low Side Driver
40-413-003
Digital I/O
The 40-413 range is available in three configurations, a high side only, a low side only and a combined high and low side (shown here) –each capable of driving 2A loads. Each output is fully protected against over-voltage, over-current and thermal overload, ensuring robust and reliable operation in the toughest test environments.
-
Product
PCIe-5764, 16-Bit, 1 GS/s, 4-Channel PCI FlexRIO Digitizer Device
785958-01
FlexRio Digitizer
The PCIe-5764 is a PCI FlexRIO Digitizer Device that simultaneously samples four channels at 1 GS/s with 16 bits of resolution and features 400 MHz of analog input bandwidth. With up to 70 dB of SNR, the PCIe-5764 is ideal for applications that require a wide dynamic range with a wideband digitizer. The FlexRIO driver includes support for finite and continuous streaming modes, and you can implement custom algorithms and real-time signal processing on the LabVIEW-programmable Xilinx Kintex UltraScale FPGA.
-
Product
32-Ch Isolated Digital Output EtherCAT Remote I/O Module
AMAX-4834
Digital Output Module
Suitable for EtherCAT networks32-ch digital output with 2,500 VDC isolationWide output voltage range (5 ~ 40 VDC) and high output current (350 mA/ch)Quick removable European type connectorLED indicators for I/O statusSupports EtherCAT Distributed Clock (DC) mode and SyncManager modeTwo Rotary switches for up to 256 slave IDs
-
Product
RS-232 Cable, 9 Pin (f) To 9 Pin (f)
34398A
Digital Cable
The Keysight 34398A is an RS-232 cable, 9 pin (f) to 9 pin (f). Standard RS-232 cables are easy to find, but making them work is a different story. The Keysight 34398A has been verified for compatibility with Keysight's bench instruments to take the mystery out of RS-232 pinouts. The Keysight 34398A includes a 9-pin (f) to 9-pin (f) RS-232 cable and a 9-pin (m) to 25-pin (f) adapter.
-
Product
Handheld Clamp Meter, 3 ½ Digit
U1213A
Digital Multimeter
Handle large currents up to 1000 A safely with 2-inch large jaw opening. Wider range DCV, ACV and resistance. Keysight Remote Link Solution allows datalogging wirelessly via Bluetooth.
-
Product
Handheld Digital Multimeter, 4 digit, Water and Dust Resistant
U1271A
Digital Multimeter
Feature sets that meet traditional industrial requirements and improve productivity and safety Improved accuracy and resolution to meet traditional industrial requirements (30,000 counts resolution with 0.7% for ACV accuracy)Intelligent features to improve productivity and safety (selectable Low Pass Filter LPF and quick signal type identification Qik-V)Better grip Both visual and audible continuity indication in noisy environments Easy access to fuse for simplified maintenance Easy connectivity to PC and internal memory (up to 200) for data logging Large rotary switch and buttons that are easy to operate Dust and water resistant casing (IP 54 compliant)Compatible with U1177A/U1117A IR-Bluetooth adapter for remote monitoring & datalogging Altitude: 3000 meters
-
Product
NI-9472, 24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module
779004-01
Digital Module
24 V, 8-Channel (Sourcing Output), 100 µs C Series Digital Module - The NI‑9472 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each channel is compatible with signals from 6 V to 30 V, … features transient overvoltage protection between the output channels and the backplane, and has an LED that indicates the status.
-
Product
PXI Digital Multimeter
Digital Multimeter
PXI Digital Multimeters, or DMMs, feature AC/DC voltage, AC/DC current, 2- or 4-wire resistance, and frequency/period measurements, as well as diode tests. You can also choose a PXI DMM with an isolated, high-voltage digitizer that can acquire waveforms at sample rates up to 1.8 MS/s at full input range, up to 3 A or 1,000 V. Additionally, you can choose a PXI DMM that can perform basic inductance and capacitance measurements.
-
Product
PXIe 8 Bit High Speed Digitizer - 5 GS/s on 1 Channel, 1.5 GHz Bandwidth
M4X.2230-X4
Digitizer
The 9 models of the M4x.22xx-x4 Express series are designed for the high speed data acquisition. Each of the input channels has its own A/D converter and its own programmable input amplifier. This allows the recording of signals simultaneously on all channels without any phase delay between them. The extremely large on-board memory allows long time recording even with the highest sampling rates.
-
Product
PXIe-6571, 1-Slot, 100 MVector/s PXI Digital Pattern Instrument
786320-01
Digital Pattern
1-Slot, 100 MVector/s PXI Digital Pattern Instrument - The PXIe‑6571 is designed for semiconductor characterization and production test. It includes the Digital Pattern Editor for configuring pin maps, specifications, levels, timing, and patterns. It also includes debugging tools … like Shmoo, digital scope, and viewers for history RAM, pin states, and system status. The PXIe-6571 requires a chassis with 82 W slot cooling capacity, such as the PXIe-1095.
-
Product
PCIe 16 Bit Multi-purpose Digitizer - up to 20 MS/s on 4 Channels (Single Ended) or 2 Channels (Differential)
M2P.5922-X4
Digitizer
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
Product
NI-9426, 24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module
780030-02
Digital Module
24 V, 32 Channel (Sourcing Input), 7 µs C Series Digital Module - The NI‑9426 works with industrial logic levels and signals to connect directly to a wide array of industrial switches, transducers, and devices. Each digital input line is compatible with 24 V logic levels.
-
Product
PCI-6521, 16-Channel, ±30 VDC, 8 Sink/Source Inputs, 8 Relay Outputs (150 V), Isolated Digital I/O Device
779312-01
Digital I/O
The PCI-6521 is an industrial digital I/O module with high channel isolation and industry-standard 24 V logic levels. If a computer or application fault occurs, the PCI-6521 can use … digital I/O watchdogs to switch to a configurable safe output state to ensure detection and safe recovery from fault conditions. It also features programmable power-up states, digital filtering, and change detection for optimal control over your application.
-
Product
32-CH Sourcing Type Digital Input EtherCAT Module
EPS-1032
Digital Input Module
ADLINK" s EPS slave system features modular design for flexible high channel density, rugged construction, easy maintenance, and intelligent performance, compatible with 3rd party EtherCAT products. Precise time-deterministic control enables I/O synchronization for critical applications, and FPGA and ARM technology allow users to fully monitor status of EPS modules and systems, including operating temperature and usage cycle of relay switching, as well as motion control status for general purpose motor drive control. In addition, the ADLINK EtherCAT configurator enables auto-scan and configuration across EtherCAT systems. The EPS" unique structural and electronic design supports hot-swappable function, reducing repair time, and the rugged construction and operating temperature range of -20°C to 60°C allow operation in the harshest environments.
