PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
product
Low Profile PCI Express 2-Port
7205ec
The 7205ec low-profile PCI Express serial interface provides two serial ports configurable for RS-232, RS-422 or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates exceeding 1 Mbps. These features make the 7205ec ideal for data-intensive applications that require reliable, ultra-fast throughput rates.
-
product
Serial-to-Daq Minibox
Model 2367
* 2367 provides 32 digital I/O lines, 4 analog outputs, 6 analog inputs, 6 relay driver outputs and 4 temperature inputs.* Firmware supports ASCII command strings, Addressed commands for RS-485 networks and packet protocol. * Operates as a RS-232 as a RS-485 to Data Acquisition Module. * DB-25 connector has both RS-232 and RS-485 signals.* SCPI commands and IEEE 488.2 compatibility provide GPIB like operation over the serial link. * The 2367 is packaged in a CE approved Minibox™ metal case to minimize EMI/RFI. * 1 U high Rack Mounting Kit mountsone or two 4867s.* Plug-on Terminal Board simplifies wiring connections.* Includes Universal Power Adapter and 62-pin mating connector.
-
product
8 Port PCI Express
PEX 8609
The ExpressLane™ PEX 8609 offers 8 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 8 flexible ports and fully conforms to the PCI Express Base Specification, rev 2.0. PEX 8609 architecture supports a high-performance DMA engine with four DMA channels and internal buffer space for internal descriptor support. Up to 256 descriptors are supported internally or alternatively descriptors can also exist in host memory.
-
product
VXI PCI Express Crate Controller
V124
The V124 is a VXI bus master crate controller, usable as a crate slot 0 arbiter or as a secondary controller. Each PCI Express cable driver board, in a PC backplane, can drive one to four V124s over standard, flexible PCI Express cable assemblies up to 7 meters long.
-
product
PMC to PCI Adapter / Carrier
PMC2PCI
The PMC2PCI ( PMC to PCI ) adapter / carrier converter card provides the ability to install a PCI card into a standard PMC slot. The PMC2PCI has two PCI card slots mounted to a PMC card. One slot can be used at a time with the choice of 3V or 5V IO and 32 or 64 bit data paths.
-
product
PCI Direct Digital Synthesizers
SYNTH300-TRIG
These devices provide two synchronized DDS-based RF channels on a single PCI card. With fine frequency and phase control, triggered operation, and the ability to accept an external clock, the Synth300 products enable a number of advanced applications at a fraction of the cost of conventional equipment. In addition to two analog outputs, the product can be ordered with one (or two) LVDS outputs for programmable digital clock applications, and can be configured for control by externally supplied TTL signals for low-latency triggered operation such as PSK, FSK, and triggered sweep operation.
-
product
PCI Express 8-Port
7804ec
The 7804ec PCI Express serial interface provides eight multifunction serial ports, each individually field-configurable for RS-232, RS-422, or RS-485. Each serial port features an ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allowing the adapter to support the widest range of standard and non-standard baud rates to 230.4 Kbps (RS-232) and exceeding 1 Mbps (RS-422/485).
-
product
PCI Precision Resistor Card 9-Channel, 1.5Ω To 1.81kΩ
50-297-022
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI High Density Matrix, Dual 20x4 1-Pole
50-511A-021
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards.
-
-
product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
product
Low Profile PCI Express 1-Port
7106e
The 7106e low-profile PCI Express serial interface provides a single serial port configurable for RS-232, RS-422, RS-485 or RS-530. The ultra high-speed UART, flexible clock prescalar, and large 256-byte Tx/Rx FIFOs allows the adapter to support the widest range of standard and non-standard baud rates exceeding 921.6 K bps. These features make the 7106e ideal for data intensive applications that require reliable, ultra-fast throughput rates.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 5.82MΩ
50-297-152
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI High Density Matrix, Single 44x4 1-Pole
50-513A-021
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
product
PCI Precision Resistor Card 3-Channel, 3Ω To 22.3MΩ
50-297-154
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI FPGA Board
PCIe-8324-DSP
The Conduant PCIe-8324-DSP FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PCI Express interface and its two 12-lane HSS interfaces while performing complex calculations.
-
product
PCI 2 Amp Multiplexer, Quad 16-Channel, 1-Pole
50-635A-008
The 50-635A-008 is a quad 16-channel, 1-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
Digitizer/Oscilloscopes for PCI Express Bus
Wuntronic Digitizer/Oscilloscopes for PCI Express Bus
-
product
Osprey PCI Qbus Adapter
9668
Dual-height card plugs into PDP-11 Qbus backplane. Fibrechannel cable plugs into Qbus logic connector on Osprey /TXP. I/O Adapter logic provides Programmed I/O and DMA access to "real" Qbus compatible controllers (those not otherwise emulated).
-
product
PCI 2 Amp Multiplexer, Single 8-Channel, 4-Pole
50-635A-103
The 50-635A-103 is a single 8-channel, 4-pole MUX and is part of a range of PCI Multiplexer cards available in 9 standard density and 9 half density configurations, all using high quality electro-mechanical signal relays allowing each channel to switch current up to 2A and voltage up to 300VDC/250VAC.
-
product
8 Port PCI Express
PEX 8608
The ExpressLane™ PEX 8608 device offers 8 PCI Express Gen 2 (5.0 GT/s) lanes, capable of configuring up to 8 flexible ports. The switch conforms to the PCI Express Base Specification, rev 2.0. The PEX 8608 architecture supports packet cut-thru with the industry's lowest latency of 140ns (x4 to x1) and offers two virtual channels for traffic prioritization in the system.
-
product
PCI RTD Simulator Card 6-Channel PT100
50-262-101
This RTD Simulator is a PCI card that supports 6 channels of RTD simulation. The card provides a setting resolution of <8mΩ (also available in <90mΩ - PT1000version) and a resistance accuracy of better than 0.1% on all channels. Each simulation channel is able to provide a short or open circuit setting to simulate faulty wiring connections to a sensor. Calibration or verification of each resistor channel can be verified by using the calibration port connected to a high performance DMM and a supplied software package.
-
product
PCI Express 4 Base Specification Receiver Test Automation
N5991PB4A
The N5991PB4A is the receiver test automation software for bit error ratio testers, allowing you to test and characterize PCI Express 4.0 ASICs.
-
product
PCI Express® Electrical Performance Validation and Compliance Software
D9040PCIC
D9040PCIC PCI Express Transmitter Test Compliance Software for PCI Express 4.0 (PCIe 3.x, 2.x and 1.x also supported).
-
product
Dual Bus 64-Channel 2A PCI Fault Insertion Switch
50-190-102
This PCI fault insertion switch range is available with 75, 64 or 36 channels. It is primarily designed for the simulation of fault conditions in automotive & avionics applications involving the reliability testing of safety critical controllers. The Stimulus/Measurement to UUT path is suitable for supporting CAN and FlexRay bus systems.
-
product
PCI Precision Resistor Card 18-Channel, 1Ω To 239Ω
50-297-013
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. It is particularly well suited to applications such as the testing of engine controllers where resistive sensors provide information on parameters such as temperature.
-
product
PCI 16 Reed Relay Output Digital Interface
8003
The 8003 PCI digital I/O interface provides 16 Reed relay outputs provide high quality, long-life, low current (10 Watt maximum), dry contact switch closures. Reed relays are well suited for low-current applications. The relays are normally open, and close when energized. Writing a 1 to the proper port bit can individually energize each relay.
-
product
88-lane, 44-port, PCI Express
PEX89088
The new PCIe Gen 5.0 (32 GT/s) PEX89000 series builds on the longevity of the Broadcom series of switches, now spanning 13 families. The PEX89000 family allows customers to build systems from simple PCIe connectivity inside the box to high-performance, low-latency, scalable, cost-effective PCIe fabrics for composable hyper-scale compute systems supporting ML/AI and Server/Storage applications.
-
product
PCI Express 4.0 Test Platform
The PCI Express 4.0 Test Platform provides a convenient means for testing PCIe 4.0 add-in cards with an internal interposer and power supplies. The Summit Z416 Test Platform provides the platform for the Summit Z416 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen4, Gen3, Gen2 or Gen1 hosts and devices. It supports SMBus and other sideband signals.
-
product
Fibre Channel Test & Simulation Interface for PCI Express
PCIe-FC4
Avionics Interface Technologies
Half-size four lane PCIe board - Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speedsComprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent Analyzer - Supports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
