PCI DAQ
Data Acquistion instruments configured to work in a PCI bus.
-
Product
PCI to PC/104+ Bus Adapter
327/328
-
Model 327 and 328 are bus-to-bus adapters that allow operating a PCI board from a PC/104+ card stack. They allow selection of important PC/104+ signals using jumper plugs, thereby avoiding the requirement of using hardwired settings. Model 327 aligns the PCI board parallel to the PC/104+ boards, while model 328 places it perpendicular.
-
Product
PCI & PXI Signal Amplifiers
-
Low power supply rails, a main part of the PXI, cPCI and PCI equipment, are a common cause for an inability to produce high voltage output. Tabor Electronics’ new amplifiers convert the supply rails to higher voltage suitable for signals up to 40Vp-p, thus solving thit problem.
-
Product
Data Acquisition (DAQ) And Real-time Control Systems
-
Our data acquisition devices are capable of storing hundreds of analog and digital channels at full speed while allowing in parallel data to be sent out in real-time to any 3rd party EtherCAT master controller. We have brought the worlds of data acquisition and real-time control closer together which will save you time and money in a big way.
-
Product
PCI Express Card
-
Axiomtek develops a full spectrum of PCI Express cards to help customers accelerating their design and reducing development costs.
-
Product
PCI Express PLL Test Application
N1081PLCA
-
Keysight N1081PLCA PCI Express PLL Test Application designed to measure transmitter PLL bandwidth and peaking based on the PCI Express 5.0 TX PLL Specifications. Use N1081PLCA PCIe PLL test software to test, debug and characterize your PCIe designs.
-
Product
PCI Standard Programmable Resistor Cards
-
Pickering's PCI Standard Programmable Resistor Cards include fully programmable resistor and potentiometer cards for applications such as sensor emulation that require fine adjustment with a resolution down to 0.25 Ohm. All of our Programmable Resistor Cards can easily be formed to make Programmable Potentiometers by connecting two channels in series, using the unconnected terminals as the A and B connections and the link between the two channels as the wiper connection.
-
Product
Passive XMC-to-PCI Express Adapter
5933
-
The Technobox, Inc. P/N 5933 is designed to adapt a single-wide XMC card to an 8X PCI Express slot. The 5933 supports P15 only and allows access to PN4 signal via the adapter's DIN connector. The A and C rows of a 96-pin DIN connector connect with the 64-pin user I/O connector (J4/P4) on the mezzanine card, permitting internal connection of rear I/O.
-
Product
PCI MPEG Encoder
614
-
Real time MPEG-4/2/1 and MJPEG plus audioAdvanced video overlay for annotation or captionUncompressed preview and capture through PCIBuilt-in motion detectionLinux and Windows drivers supplied with SDK
-
Product
RTD Measurement for PCI
PCI390
-
The PCI390 features six 2-, 3-, or 4-wire high-accuracy RTD measurement channels. Each channel has programmable alarm limits on which an interrupt can be issued. The local DSP (TMS320C203) performs linearization, auto-calibration and alarm-limit checking. Sensor-data is available in °C, °F, K and Ohms. All inputs are optically isolated from the system.
-
Product
PCI Daughter Boards
DB-24C
-
The DB-24C has 24 channels of optically isolated digital outputs, arranged into four isolated banks.
-
Product
PCI Express 3.0 Test Platform with SMBus Support
Test Platform
The Summit Z3-16 Test Platform with SMBus Support allows the Summit Z3-16 to act as a host emulator, and provides a general purpose test backplane and interposer for testing Gen3, Gen2 or Gen1 hosts and devices. In addition, it supports the Summit Z3-16 with SMBus Support by providing SMBus tapping connectivity.
-
Product
PCI Precision Resistor Card 18-Channel, 1Ω to 31.5Ω
50-297-010
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Express 16 Isolated Input Digital Interface (3-13V)
8006e
-
The 8006e PCI Express digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, pushbuttons, and other user inputs. The inputs can sense both AC and DC voltage while providing optical isolation, which eliminates spikes and surges present in industrial environments. The board is PCI Express X1 compliant and is compatible with any PCI Express slot.
-
Product
PCI/ ISA Data Acquisition Boards
-
Your product Our PC Data Acquisition Boards come in a wide range of digital and analog combinations for your control, data logging and monitoring applications. Our DAQ boards offer a wide range of combinations of Digital and Analog channels. They offer plug and play installation, Windows PCs and Linux drivers, SDK and demo programs.description goes here.
-
Product
PCI Daughter Boards
DB-1825/1/DIN (with DIN rail mounting kit)
-
Screw terminal board using 37 pin cable I/O ports for PCI-1202/1602/1802/822/826 series , (32 channel single-ended ,16 channel differential)Blank pads for break detection, Low-pass filter , current shut and voltage divider (manual soldering)Dimensions :170 mm x 114 mm
-
Product
PCI FPGA Board
PCIe-8324-DSP
-
The Conduant PCIe-8324-DSP FPGA board provides a user programmable hardware platform that is able to sustain full-duplex high-bandwidth transfers through its 8-lane Gen3 PCI Express interface and its two 12-lane HSS interfaces while performing complex calculations.
-
Product
PCI Analog Input Board
APC330
-
The APC330 has many features to improve your overall system throughput rate. You can scan all channels or define a subset for more frequent sampling. Burst mode scans selected channels at the maximum conversion rate.
-
Product
PCI Carrier Board
MS 1714
-
*64 bit PCI edge connector*64 bit PMC connectors*Operated frequency up to 66MHz*Regulated 3.3v supply to module
-
Product
1-Port PCI Express Camera Link, Base Frame Grabber
PCIE-1121B-AE
-
Half-Size PCI Express Board Gen 2.0 x4Camera Link clock up to 85 MHzSupports 1 Base CL cameraBoth CL and I/O connector on one bracket (only one slot needed)Supports PoCL and non-PoCL cameras with SafePowerImage sizes up to 268,435,456 x 16,777,216Independent I/O (trigger, encoder, strobe, etc) for each camera
-
Product
3U CompactPCI Mini PCI, Mini PCIe Carrier Board
cPCI-3W10
Carrier Board
- Supports 32bit, 33/66MHz CompactPCI® bus- One SIM card socket- One Mini PCI and one Mini PCIe socket- PICMG® 2.0 R3.0 compliant
-
Product
Full-Size PCI Express Mini Module With Gigabit LAN
AX92902
-
*Supports 10/100/1000 Mbps transfer rates*Supports Wake-on LAN*Supports PXE Boot ROM*Intel® i210IT controller*51 x 30 mm
-
Product
Ethernet/AFDX/BroadR-Reach PCI Fault Insertion Switch - 4 Channel
50-201-004
Fault Insertion Unit
This high bandwidth differential PCI fault insertion card is designed to simulate common faults on high speed two wire communication interfaces such as Ethernet. This card supports 4 or 8-channels of two wire serial connections and can be used for simulating faults on Ethernet, AFDX, Broad R-Reach, 100BaseT and 1000BaseT interfaces. Any wire can be set to an open circuit, shorts can be applied across the wire pair, or to the adjacent pair. Fault connections can be made to one of four external signals via two fault buses, typically simulating connections to a supply voltage or ground.
-
Product
PCI 16 Isolated Input Digital Interface (10-30V)
8006H
-
Optimized for sensing up to 24V inputs, the 8006H PCI digital I/O interface provides 16 optically isolated inputs for connection to devices including sensors, switches, push buttons, and other user inputs.
-
Product
PCI Fault Insertion Switch Cards
-
Pickering's PCI Fault/Signal Insertion Switch Cards feature a breakout arrangement that allows faults to be attached to the sensor lines, this includes the breaking of a connection or the adding of defect all of which can simulate connectivity problems in the system.
-
Product
3U Rackmount Appliance for PCI Express® Gen5
R300-G5 Pro
-
Is a robust, versatile test system designed to test and debug solid state drives (SSDs) of all popular storage interfaces and protocols.
-
Product
PCI High Density Matrix, Dual 20x4 2-Pole
50-511A-022
Matrix Switch Module
The 50-510A series of matrix cards feature a wide range of switching configurations (22x4, dual 20x4, 22x8 and 44x4). Larger matrices may be constructed by daisy chaining the common signals from multiple cards. Expansion cables are available for the 50-512 and 50-513: The 50-512 can be expanded to 44x8 or the 50-513 can be expanded to 88x4 using two cards linked by the ribbon cable assembly 50-976-020-0.1M. Also the 50-512 can be expanded to 22x16 or the 50-513 can be expanded to 44x8 using two cards linked by the ribbon cable assembly 50-976-050-0.1M.
-
Product
PCI Counter/Timer with Quadrature Board
APC483
-
Several models with a variety of configurations provide up to ten counter/timer channels for counting events, generating waveform control signals, measuring pulse-widths, periodic rates, or quadrature position and monitoring operations.
-
Product
PCI 9 Channel Precision Resistor Card
50-297-002
Programmable Resistor Modules
The 50-297 provides a simple solution for applications requiring accurate simulation of resistive sensors. The 50-297 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
PCI Express Multi-Function Boards
PCIe-8622
-
PCI Express, 200 kS/s High-speed, 16-bit 8/16-channel Simultaneously Sampled Analog Input Board with 4/12-channel Isolated DIO
-
Product
PCI-8433, 4-Port, PCI, Isolated, RS485/RS422 Serial Interface Device
779146-01
Serial Interface
The PCI‑8433/4 is a high-performance industrial interface for high-speed, port‑to‑port isolated communication with RS485 and RS422 devices. It features high-performance DMA transfers, multithreading, and multiprocessor support. You can also select between 4‑ and 2‑wire transceiver modes for full‑ and half‑duplex communication. NI serial interfaces also appear as standard COM ports for compatibility with programs that use serial communications.
