Walk-in Chambers
-
Product
Laboratory Ozone Test Chamber
CX-150
-
Shenzhen Chuangxin Instruments Co., Ltd.
Laboratory Ozone Test chamber is widely used to control products quality in measuring quality control; Rubber & Plastics; automobile production; wire and cable; packing materials; instruments and meters; medical equipment; civilian nuclear energy; civil aviation; colleges and universities; research laboratories; inspection arbitration, and technical supervision departments and other rubber products.
-
Product
Altitude Test Chambers
-
Altitude chamber testing is important for manufacturers of products that might be shipped via air. It is especially important for defense and aerospace applications where pressure and vacuum conditions are even more intense. Our altitude test chambers simulate a variety of environmental conditions including temperature, altitude, humidity, and vibration for the rigorous testing standards of combined environment.
-
Product
Benchtop Temperature Chamber | Environmental Test Chamber
-
The first true Hybrid Temperature Chamber/Platform combination called the Hybrid Benchtop Chamber. The floor of the chamber is a completely functioning Hot/Cold Plate, independent or simultaneous with the chamber. Our models come in different sizes: Micro, Small, and Medium thermal Chambers.
-
Product
Antenna Measurement Chambers
-
Antenna measurement chambers can be utilized to make far-field antenna pattern measurements. These chambers are designed either in a rectangular or tapered configuration depending on the frequency range of interest.
-
Product
Liquid-To-Liquid Thermal Shock Chambers
-
Purchasing a liquid thermal shock chamber needs close consideration of the long term operating costs. The specialized liquids used can easily evaporate, causing the loss of thousands of dollars of fluid per year, if not properly contained. Liquid-to-liquid thermal shock testing is typically conducted to apply very strong, repetitive thermal stress to test pieces. It can model a product's ability to withstand thermally-induced size changes, crack resistance, hermetic integrity, and changes in electrical properties. This form of testing provides a very rapid temperature shock recovery of conditions, and it can significantly reduce testing time by requiring shorter soaks and less cycles.
-
Product
Battery Temperature Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Sanwood climatic chambers for battery can be tested under controlled temperature and humidity conditions, similar to the conditions under which batteries operate during their lifetime.
-
Product
Near-field Chambers
-
Most antenna measurements need to be carried out in the far field; that is, the test antenna should be illuminated by a plane wave. Typically this is carried out by providing sufficient separation between the source and the AUT so the spherical wave approaches a plane-wave character.
-
Product
Vibration Test Chamber Gantry Frame System
-
Guangdong Test EQ Equipment co., Ltd.
- Structural Design: Monolithic construction with seamless TIG welding for durability and aesthetics. Lever-driven door lock mechanism.- Smart Control System: Features a Chinese/English-language color LCD touchscreen HMI + high-performance PLC, powered by TESTEQ's proprietary software for automated, intelligent, and user-friendly operation.- Energy Efficiency: Incorporates TESTEQ's patented "Static Balance" technology, reducing energy consumption by over 30% during low-temperature stabilization.- Vibration Integration: Gantry Frame System: Worm gear-driven vertical adjustment and lateral positioning via wireless remote.- Advanced Sealing: Custom flexible connectors ensure airtight integration between temperature/humidity chambers and vibration platforms.
-
Product
Vertical Flammability Chamber
TF312
-
TESTEX Testing Equipment Systems Ltd.
Vertical Flammability Chamber for measuring the vertical flame spread of children’s sleepwear, fabrics (fabric burn test), other textile materials or resilient filling materials used in upholstered furniture. Vertical Flammability Chamber complies with ASTM D6413, CALIF TB117, 16CFR Parts1615/1616, etc. Please contact us for more information about flammability test method.
-
Product
Condensation Chamber
-
Wewon Environmental Chambers Co, Ltd.
The condensation test chamber does not need special installation conditions, just need to connect to the ordinary power supply and running water can be used normally. The functional diversity of the equipment, fast and low operating costs make the machine a very high cost performance condensation testing machine in the market. The machine can be programmed to control three different test effects: Humidification, natural cooling and drying, and the corresponding temperature and running time of each test, and set the total time of program running and the number of cycles. The condensation tester has an automatic water replenishing device. When the water temperature exceeds the upper limit, there will be a protection device for safety warning, and it is very safe to use.https://www.wewontech.com/condensation-chamber/
-
Product
Xenon Lamp Weather Resistance Test Chamber
-
SN Xenon lamp test chamber adopts the Xenon ARC lamp that can simulate full sunlight spectrum to reproduce destructive light waves existing in different environments so as to provide the corresponding environment simulation and acceleration test for scientific research, product development and quality control.
-
Product
Zero Gauss Chamber
-
Measuring station for reproducible and location-independent measuring results for quality assurance, eg B. for cross-company supply chainsMeasurements of residual magnetism on ferromagnetic components are no longer significantly falsified by ambient magnetic fields induced in the object passive shielding, no power consumption and maintenance-free defined measuring station, good measuring room accessibility Platform in a robust design
-
Product
Battery Module Test Chambers
-
Guangdong Bell Experiment Equipment Co.,Ltd
This test chamber series mainly for testing the battery module of Electric-bike, Electric Motorcycles, etc. These series meet the standard compliance of IEC62619, UL2580 and GB31485-2015. Including short circuit, thermal test, drop test and crush test, etc.
-
Product
Thermal Shock Test Chamber
-
observe the product characteristics and failure occurrences caused by different materials and their thermal expansion coefficients, thermal shock testing is subjected to the product. In thermal shock testing alternating high and low temperatures are fed in the chamber. WEIBER designs and manufactures customised THERMAL SHOCK CHAMBERS with separately controlled temperature zones (2 zone and 3 zone), liquid to liquid (2 zone) depending on configuration of the chamber chosen.
-
Product
Dust Chamber Manufacturer
-
Wewon Environmental Chambers Co, Ltd.
Wewon Environmental Chambers Co., Ltd. is a good dust chamber manufacturer and made a 3380 liters blowing sand and dust test chamber for a Vietnam customer last week. The controller system of this 3380 liters dust test chamber can be connected to the computer.
-
Product
Laboratory Test Equipment Temperature Cycling Steam Aging Test Chamber
-
Shenzhen Chuangxin Instruments Co., Ltd.
Steam aging test machine is used to test and determine the parameters, performance of electrical, electronics, other products and materials for high temperature, low temperature, or the temperature of the thermostat test environmental changes.
-
Product
Vehicle Salt Spray Test Chamber
-
Dongguan City Simplewell Technology Co. Ltd.
Vehicle Salt Spray Test Chamber by Simplewell
-
Product
Thermally Protected Ballast Heating Test Chamber
TPB-UL935
-
Working room dimension: 610×610×610mm• Temperature range: RT+10℃～+100℃• Materials of inner and outside chamber: Senior stainless steel• Insulation Material: Ultra-fine glass wool insulation material• Heater: Dedicated strip heater (heating surface area of 300 × 40 mm), each group three hundred watts, a total of four groups, with the power supply in parallel.• Special wooden test sample holder• Third gear temperature measurement points (at any time monitoring and conversion)
-
Product
Compact Benchtop Humidity Chamber
-
Guangdong Test EQ Equipment co., Ltd.
- Space-Efficient Design: Lightweight (40–80 kg), corrosion-resistant stainless steel interior, and transparent double-glazed door for sample visibility.- Precision Control: PID-regulated systems with touchscreen interface, programmable cycles (up to 1,000 steps), and real-time data logging via USB/Wi-Fi.- Energy-Saving Technology: Eco-friendly refrigerants (R513A/R23) and variable-speed compressors for reduced power consumption.- Safety & Durability: Overheat/overcurrent protection, automatic defrosting, and reinforced insulation for long-term reliability.- Modular Customization: Optional CO₂/O₂ injection, vibration modules, or UV lighting for specialized testing.
-
Product
Reach-In Stability Chambers
-
The PH series chambers are designed for performance specifications exceeding FDA and ICH requirements.
-
Product
Temperature Humidity Chamber
-
Xi'an LIB Environmental Simulation Industry
Designed to simulate precise environmental conditions for testing materials, components, and products.
-
Product
Antenna Test Systems and OTA Chambers
-
With our well-established experience in innovative solutions based on top-quality engineering, Rohde & Schwarz provides you with leading antenna test systems and OTA chambers.
-
Product
Stability Testing Chambers
-
A stability testing chamber is a specialized enclosure used to control and maintain specific environmental conditions, primarily temperature and humidity, for extended periods. It's used to assess the stability and shelf life of products, materials, or substances by subjecting them to controlled environmental stress.
-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
IEC60529 IPX7 Water Immersion Test Chamber
-
Shenzhen Chuangxin Instruments Co., Ltd.
This device is designed and manufactured accordance with requirements of IEC 60529 and GB4208-2008
IPX7 level. Applied to waterproof test of luminaire and household appliance. -
Product
Shielded Chambers
-
GTEMCELL Ltda shielded chambers are built up as a modular construction. Due to individual modules any size of chamber can be realized. Big chambers may require an outer supporting structure or alternatively the shielding material can be attached direct to the building.
-
Product
Steady State and Constant Climate Chambers / Rooms
-
is ideal for reliable stability tests and precise maintenance of constant climatic conditions. Constant temperature and humidity values are the outstanding features of this range. These constant climate chambers have large reserve capacity and a variety of optional features.
-
Product
Refrigerator Type Constant Temperature And Humidity Chamber
THC Series
-
Optimal chamber for testing materials with mechanical properties sensitive to temperature and humidity effects, such as fibers, paper, or films. Temperature regulation: Automatic control by heater and refrigerator.
-
Product
Glass Door Humidity Chambers
FW30
-
The Bemco FW30, mechanically cooled, Glass Door Humidity Chamber has a temperature range of -18 C to +94 C (0 F to 200 F) and a humidity range of up to 5% RH to 95% RH. This chamber features dry air injection and a direct humidity sensor. It operates without dewpoint limit from 5% RH to 95% RH over the range of 30 C to 85 C and even allows operation at 20% RH at 5 C and 50% RH at -14 C!
-
Product
Steam Aging Test Chambers
-
Dongguan Amade Instruments Technology Co., Ltd
Steam aging test chamber is a climatic test machine used to judge the products performance to resist extreme circumstance under high temperature, high humidity and high pressure during the transportation, storage and usage. The principle is very simple, water in the tank is heated turning into steam to form a simulated test environment under specified temperature and humidity. Specimens are placed into the drawers of machine to carry out test lasting for preselected time. It is applicable to electronic connectors, semiconductor IC, transistor, LCD, diodes, resistances etc.
