Verifiers
-
Product
Signal Generator
MX-RFSG1800
-
The Maxcom MX-RFSG1800 signal generator is a simple low-cost device used to inject RF signals up to 1800 MHz into RF plant for the purpose of verifying those high frequencies are able to properly pass-through cables, passive and active devices.
-
Product
Personal SerDes Testers
C Series
-
Everything you need to develop and verify your high-speed digital algorithms is contained in these ultra-portable test instruments. They will forever change the way you think about developing and verifying Gbps digital and mixed-signal algorithms, and they will allow you to measure signals in ways that were not possible in the past. Each personalized SerDes tester is equivalent to multiple hardware platforms, containing everything that you need to make high-performance measurements like bit error rate testing, signal generation, and signal measurement.
-
Product
Seismic Acquistion QC Serivices
-
Overall data quality / cost monitoring / safety / daily reporting to client. Verif-i provides technical and operational programme assurances for seismic surveys conducted for the company. The lead acquisition QC on-board/on-crew the seismic vessel/block accepts or rejects data on behalf of the company. Our representative will assist the contractor in fulfilling the technical and operational requirements of the seismic programme and report on crew activities.
-
Product
Analyse-it Method Validation Edition
-
Validate and verify your analytical and diagnostic methods to meet the demands of regulatory compliance.
-
Product
Logic Probes
-
Logic probes are used to analyze the logic states (high/true: logic 1 or low/false: logic 0) of digital signals. To verify and debug today’s high-speed, low-voltage digital signals, you need logic probes that can accurately acquire signals from a wide variety of electronic designs, while protecting signal fidelity. Tektronix logic analyzer probes contain a variety of connectivity options that are engineered to ensure that signal acquisition is a true reflection of your design's performance. Compare and learn more about Tektronix logic analyzer probe solutions below.
-
Product
EXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5171B
Signal Generator
Achieve faster throughput and greater uptime with the cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading output powerThoroughly verify receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
Product
CI/CD Software
-
See everything that touches your code, strengthen the security posture of source code repositories, and verify the integrity of every build.
-
Product
Source Code Review
-
Source code review, also known as Security Code Review is the process of auditing the source code for an application to verify that the proper security controls are present, that they work as intended, and that they have been invoked in all the right places. Code review is a way of ensuring that the application has been developed to be “self-defending” in its given environment.
-
Product
Self testing clamps with Visual Indication
Bond-Rite EZ
-
The Bond-Rite EZ is an easy to use hand-held portable static bonding device that can quickly and securely establish and verify an equipotential bond between equipment for operations conducted in hazardous locations.
-
Product
Logic Analyzer Probe
FS2521
-
The FS2521 is a logic analyzer probe used to test DDR4 SO-DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4164A logic analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR4 SO-DIMMs. Now qualified at 3200MT/s
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm - SPST
50-294-121
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
RF Deluxe
ICAP/4Rx
-
ICAP/4Rx RF Deluxe is an extended version of ICAP/4Rx, including simulation capability for RF frequency design. This powerful system includes everything you need to design and verify all types of board, engineering system and IC-level design. Of course, ICAP/4Rx Power Deluxe includes Intusoft's time-tested "IsSpice4" analog and mixed-signal simulation kernel, featuring more enhancement than any SPICE kernel on the market for convergence, accuracy, speed and interactive capability.
-
Product
Bar Code Verifier
TP140B Report Printer
-
The TP140B Report printer allows for printing of inspection reports from your Inspector series bar code verifier. The printer provides a simple report that will have a line for each bar code inspected. Note: The Verifier Computer Interface Report (VCIR) is required if you need the Scan Reflectance Profile (SRP).
-
Product
EasyColor
-
Fast conversion of images between 11 color spacesColor segmentation: to identify objects based on their colorColor verification: to verify the color of objects
-
Product
PCI Programmable Resistor Card 4-Channel 2 Ohm To 255 Ohm
50-294-013
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
3.0mm Preset Controls Probe
CX-A3C
-
Shenzhen Chuangxin Instruments Co., Ltd.
Used to verify protection against access to hazardous parts by use of a tool through holes which give access to pre-set controls. Meets IEC, EN, UL and CSA Standards including IEC 1010, EN 61010-1, U- 3101-1, UL 3111-1 and CSA 1010-1. The handle and stop face are made of Delrin®. The rod is stainless steel.
-
Product
Portable Bar Code Verifier
Inspector 5000 CR3 Scanner
-
The Inspector 5000 CR3 Scanner provide a Point-and-Shoot Traditional Method that also includes the ISO 15416 and ANSI X3.182 Decodability parameter grade. This unique portable bar code verifier can interface with either a CR3 scanner or the patented RJS Auto-Optic scan head. Store and print capability, multiple scan averaging and subsymbology choices are easily accessed through a simple seven-button user interface with a large color LCD display. The scanners are easily installed by the user, which makes the unit quickly adaptable to practically any verification requirement.
-
Product
Two-Pole Voltage Tester
P-6
-
SONEL P-6 has all the features that characterize the P-4 Voltage Tester and P-5 Voltage Tester. In addition, the P-6 model has the phase identification function which allows to verify the phase compatibility (and its overtaking or delay) against the phase at the reference object.
-
Product
Portable, Integrated O-Level Test Platform
Guardian™
Test Platform
Guardian is a ruggedized automated testing platform that quickly and accurately verifies the operational readiness of complex electronics systems in aircraft, ships, and vehicles.
-
Product
PCI Programmable Resistor Card 2-Channel 2.5 Ohm To 1.02k Ohm
50-294-021
Programmable Resistor Module
The 50-294 series of PCI Programmable Resistor cards are available with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single card. These cards are ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Multi-Layer Analyzer
GPON Xpert™
-
The GPON Xpert multi-layer analyzer is a unique protocol analyzer for G-PON products. GPON Xpert is a modular tool designed for R&D, laboratory and field application engineers engaged in the development, testing and deployment of G-PON standard-compliant solutions. GPON Xpert verifies the interoperability of G-PON products offered by different vendors, and indicates compliance of any combination of OLT and ONT/ONU modems to the G-PON standard.
-
Product
Live-Dead-Live Meter Verifier
LDL-1200
-
The Live Dead Live (LDL) Meter Verifier is a small, lightweight, robust, portable, handheld power supply. It supplies just under 150 volts, AC (rms) or DC with a maximum current of less than 5 mA at rated voltage. The LDL-1200 Meter Verifier is specifically designed to facilitate voltage verification tests on most digital multi-meters, electronic voltage detectors, voltage testers, neon test lights, tic tracers and other commonly used electrical voltage test apparatus, while keeping the user as electrically safe as possible with its extremely low “volt-amp” output.
-
Product
Optical Testers
-
Instruments used to analyze, certify, and troubleshoot fiber optic networks and components, ensuring they meet performance standards by measuring light power, detecting faults (breaks, bends, dirt), and verifying signal integrity, using tools like OTDRs, Power Meters, and Visual Fault Locators.
-
Product
Network Toner & Probe Kit
MT-7028
-
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
Product
PANTESTER PRO
PK-102/102PL
-
PANTESTER PRO is an advanced multifunction pin-by-pin cable tester to verify cable integrity of Datacom, Telecom and Coaxial cables and displays the test results on the main unit.
-
Product
Test Development Solution
-
Corelis will process your design information, create all necessary test vectors, and verify the test vectors using your actual hardware. This is a complete "turn-key" service resulting in a fully verified and debugged boundary-scan test system. For companies short of resources, those who are under a tight deadline, or for those who are new to boundary-scan and want to be testing in the shortest time possible, this is an excellent way to minimize your investment and maximize your effectiveness.
-
Product
PXI Resistor Module 2-Channel 2R to 32.7k with SPDT
40-293-132
Programmable Resistor Module
The 40-293 is a Programmable Resistor module with two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
IEC60529 IPX3 IPX4 Brass Water Spray Nozzle For Hand Sprayer
CX-IPX34
-
Shenzhen Chuangxin Instruments Co., Ltd.
The IPX3-4 Spray Nozzle is a hand-held test device to verify protection against spraying and splashing water.
-
Product
ELM Electronic Load Module
-
Circuit breakers are often overlooked during maintenance of electrical systems in aircraft, or often only verified for open and closed states. To test the true functional purpose of a circuit breaker it requires the application of current in excess of the rated trip value and then measure the time for the breaker to actually trip. This is the only way to verify that a circuit breaker will react as designed if an electrical failure occurs.
-
Product
NEXTest 7
PK-2030/2032/2033/2036/2037/2038
-
NEXTest 7 is an advanced and unique tester in the market. It's designed to check and troubleshoot the pin connections of Display port & HDMI prior to installation on equipment. By using advanced technology to verify the integrity (20 pins + shield) of both display port and HDMI cables, especially for HDTV installation and DIY termination in the field, solving your cable testing need, unlink all of the other testers verify 9 circuits only. It checks for opens, shorts, miswires and intermittent faults in all conductors plus shield continuity, most tester only test for opens. It displays cable map results of both TX (near end) and RX (far end) on the main unit, either on testing before or after installation cables. User can easily read and determine the actual 21 pins configuration on main unit. It employs both auto and manual scanning of 21 wires. Tone Generator mode transmits two selectable tones on each pin for use with Net Probe (PR-06P) optional, enables one to quickly locate a cable. It's capable of testing up to 8 cables and locations at one time. NEXTest 7 especially features a self-learning mode to memorize cable pin out for testing large quantity standard or custom cables for PASS/FAIL a snap, makes testing quick and more efficient.
