Verifiers
-
Product
High Accuracy In-Situ Mass Flow Verifier
HA-MFV
-
The HA-MFV, High Accuracy Mass Flow Verifier is designed for use on process tools to verify mass flow control flow rates in-situ. Available with EtherCAT® or DeviceNet™ communications and measurement accuracy of 1.0% of reading, the HA-MFV can verify MFC flow with the actual process gas significantly better than older rate-of-rise devices or process chamber rate-of rise methods.
-
Product
Bridge Decking Testing Equipment
-
The testing process can detect blow holes, inclusions or thin areas in 'sprayed-type' membranes. Because the concrete contains a small amount of water, it is electrically conductive and a DC Pinhole Detector can be used to create a high voltage which is passed over the surface by the use of a brush electrode. An alarm will sound to identify any small defects which can be rectified so that the integrity of the coating can be verified.
-
Product
Logic Analyzer Probe
FS2520
-
The FS2520 is our newest and fastest logic analyzer probe used to test DDR4 DIMM memory. It is designed to work exclusively with 3 Keysight U4164A logic analysis modules operating in either Quad Sample State or Quarter Channel 10GHz timing modes. This gives the user an extremely effective tool for debugging, testing and verifying DDR4 DIMMs running above 4000MT/s. It’s like having a 100 channel scope.
-
Product
COM Express Type 10 Starter Kit Plus
COM Express Type 10 Starter Kit Plus
Software Development Kit
The COM Express Type 10 nanoX Starter Kit Plus consists of a COM Express Type 10 core module reference carrier board that provides two PCIe Mini Card slots, 2 RJ-45 LAN ports, 2x USB 3.0, 2x USB 2.0, 1x USB client, 2x DB-9 COM, 1x SD card socket, and Mic/Linein/ Line-out. ADLINK also provides additional development tools including a verified 10.1" LVDS panel (optional), power supply, thermal solution and cabling accessories.
-
Product
Hygrometers
-
A hygrometer is a device used to measure humidity. Many hygrometer products also measure temperature. A hygrometer that measures both humidity and temperature often is referred to as a thermo-hygrometer. PCE Instruments (PCE) offers a wide variety of hygrometer products used to measure the relative humidity of the air.Since humidity is an important factor in many sectors including but not limited to manufacturing, agriculture, construction, restoration, remediation and heating, ventilation and air conditioning (HVAC), PCE also carries a number of hygrometer devices designed for specific applications such as measuring the humidity in bales of pressed hay or in rolls of paper. A hygrometer also can be used to evaluate heat stress risk in hot work environments like boiler rooms, factories, construction sites and commercial bakeries. To accurately assess heat stress risk, a hygrometer capable of detecting and classifying temperature in relation to the amount of moisture content in the air is recommended. The global standard description for heat stress is the Wet Bulb Globe Temperature Index (WBGT). A combination hygrometer / thermometer, or thermo-hygrometer, can be used to verify the integrity of the cold chain during the transport and warehousing of refrigerated food and pharmaceutical products. This versatile and popular style of hygrometer also is ideal for evaluating the performance of HVAC systems in industrial, commercial and residential properties. If the humidity indoors is too high, mold can occur. Certain types of mold cause respiratory problems and other negative health effects for people living or working in the surrounding environment. In addition, mold that has permeated into the walls or roof of a structure must be removed for safety reasons. Mold remediation and removal, also called mold damage restoration, can be a costly endeavor, which is why preventative monitoring of the humidity indoors is preferable whenever possible.
-
Product
Anite Application Testing
-
Verify higher level protocols and application enablers for a more effective roll-out of LTE-IMS based services to end-usersPerform rapid and cost-effective application testing associated with device acceptance test plans mandated by major mobile operators such as China Mobile, Verizon Wireless, AT&T and T-MobileGain access to comprehensive IMS LTE test plans mandated by standardization organizations such as GCF and PTCRB
-
Product
PNA-X Microwave Network Analyzer
N5245B
Network Analyzer
Simplify your test stations by replacing racks and stacks of equipment Increase productivity with the most integrated and flexible single-connection microwave test engine Reduce test time with the world's widest range of single-connection measurement applications Accurately test linear and nonlinear device characterization using advanced error correction Accelerate insight into component behavior using a multi-touch display and intuitive user interface Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
ICP® Shock Accelerometers
-
Piezoelectric ICP® accelerometers afford a very high signal output (+/- 5 volts full scale) and the ease of two-wire electrical connectivity. Their inherent ruggedness enables them to be severely over ranged without damage. The addition of internal mechanical isolation minimizes the high frequency stress that would otherwise be encountered by their ceramic sensing elements. This mechanical isolation, coupled with an internal 2-pole electrical filter, built into the ICP® circuitry, tailors the overall accelerometer response to assure data quality to frequencies as high as 10 kHz. Depending on the specific model, accelerations in excess of 50 kg can be successfully measured. These modern designs, with their internal elastomeric isolation materials are verified through calibration to remain dynamically linear and are enabling piezoelectric accelerometers to operate in increasingly severe acceleration environments.
-
Product
Camera Testing
FLIR
-
CI Systems' FLIR turn-key test stations carry out all the necessary tests to verify and compare the quality of an infrared/thermal camera. The FLIR test systems are based on CI Systems' NIST traceable blackbody radiation sources, collimators and special thermally controlled targets, designed to provide very accurate IR test patterns. All these combine to project standardized targets with known geometry and intensity to the Unit Under Test(UUT).
-
Product
Electrician & Technician Testers
-
EVSE's Electrician and Technician testers are created for installation professionals, and are small and durableenough to be carried in a toolbox. These weatherproof handheld units allow new chargers to be checked after installation, verifying a number of vital power and safety requirements, as they simulate the connection a charger makes with an electric vehicle. Simply plug the charger's J1772 connector into the tester's receptacle and you are ready to evaluate operation.
-
Product
Multi-Layer Analyzer
GPON Xpert™
-
The GPON Xpert multi-layer analyzer is a unique protocol analyzer for G-PON products. GPON Xpert is a modular tool designed for R&D, laboratory and field application engineers engaged in the development, testing and deployment of G-PON standard-compliant solutions. GPON Xpert verifies the interoperability of G-PON products offered by different vendors, and indicates compliance of any combination of OLT and ONT/ONU modems to the G-PON standard.
-
Product
Phase Sequence and Motor Rotation Tester
PRM-6
-
The PRM-6 Motor and Phase Rotation Tester can test the motor rotation of 3-phase systems, and verify 3-phase receptacle wiring and phase sequencing with test leads.
-
Product
Probing & Analysis Adapters
-
No matter how well designed a circuit is, there is almost always a need to hook up test instruments to it to verify function, look for bugs, or baseline performance. As IC packages become smaller and pin counts grow this becomes harder and harder. probing adapters are required to alleviate this de-bug problem. Many different types of adapters fall into the test and debug category. The common feature is that they bring the signals of an IC out to a format that is easy to interface with test and analysis equipment.
-
Product
Portable Bar Code Verifier
Laser Inspector 1000
-
The L1000 analyzes the essential traditional verification parameters including average bar deviation, quiet zones, encodation check, mod check and ratio where applicable. It also provides the ISO/ANSI method Decodability calculation and percent of decode information. Designed for maximum ease of use, even traditionally hard to verify bar codes such as high density codes with 5 mil (.13mm) X dimensions and codes on irregular, wet, shiny, laminated or moving surfaces are accurately analyzed.
-
Product
Socket Testers
-
Precision Mastech Enterprises Co.
Handheld electrical tools plugged directly into wall outlets to quickly verify if they are wired correctly and functioning safely.
-
Product
ENA Vector Network Analyzer
E5071C
Vector Network Analyzer
9 kHz to 4.5/6.5/8.5/14/20 GHz2- or 4-port, 50 ohm, S-parameter test set Improve accuracy, yield and margins with wide dynamic range 130 dB, fast measurement speed 8 ms and excellent temperature stability 0.005 dB/CObtain design confidence through complete characterization of high-speed serial interconnects with enhanced time domain analysis option Protect your investment with upgradability across all of the options Every spec verified, adjustments included Lock in support & peak performance from the start
-
Product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 63.7 Ohm - SPST
40-294-111
Programmable Resistor Modules
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
Product
Return/Insertion Loss Meter
CA6034
-
The CA6034 optical return loss/insertions loss meter is an intergrated meter for optical fiber network, and cable manufacturere to verify the quality of finber leads, with the features of handhel, intelligent and multi-functional.
-
Product
Network Toner & Probe Kit
MT-7028
-
The MT-7028 lets you easily locate and verify the cable status and troubleshoot wiring for continuity, shorts, opens and crossover on RJ45 Lan cable Cat 55e67 (UTP/STP)RJ11/12 Telephone cable Cat. 3 (2/4/6 pin) & normal solid/Stranded wire by alligator clips patch cord. Ideal for all installation and maintenance fields of telecommunication, networking, datacom, Audio/Video, cable TV, and all weather cabling, etc.
-
Product
Catena 1910 HSIC Tester
Catena 1910
-
The MCCI Catena 1910 HSIC USB Tester enables testing of HSIC Host or HSIC Device products. It can be used to exercise your product by operating as an active host or active device, while simultaneously capturing USB traffic for analysis. For test and validation of a final system, Passive Capture mode lets you debug and verify communication between your HSIC Host and HSIC Device,
-
Product
MCB Thermal Verification Test Bench
-
The test system is a special version of the thermal test test system in the sense that the test jig is primarily designed to hold and connect multi pole MCBs for thermal verification so that each pole can be verified to trip within the IEC time band after the MCB has been riveted. This test ensures the trip verification of MCB so as to trip all the 4 poles at once when overload is detected in one single pole. In short, this is a verification-only bench.
-
Product
Radar・Sensor Simulation Framework
COSMOsim
-
Millimeter Wave Radar simulator and LIDAR (Laser Imaging Detection And Ranging) simulator for Automotive sensor simulations, and also can provide 3DCG MAP for specific radar which has millimeter accuracy. Now we can only provide AMMWR and ALR to the following COSMOsim Framework. This simulator enables automotive manufacturers to simulate a driving situation by sensor-based modelling, check the recognition and control of autonomous driving, and verify the sensor-mounting positions on vehicles efficiently, which eliminates the need for test driving with real vehicles.
-
Product
Class 2 Sound Level Meter
SP79
-
The SP79 is a Class 2 sound level meter for on-site measurements in accordance with Noise at Work legislation in industrial and office environments. Featuring A and C frequency weighting and fast and slow time weighting, the compact design can be handheld, or mounted on a tripod for longer term monitoring of Min / Max values. Detailed recording and analysis can be made using the AC and DC outputs. The SP79 complies with BS EN 61672-1:2003 and is supplied with a detachable windshield and hard carry case. The large high contrast display includes both digital reading and analogue bar graph. An optional Class 2 sound level calibrator is available to verify accuracy before and after readings in accordance with international standards. The SPC70 is simple to use and provides a 1kHz reference at 94dB and 114dB.
-
Product
DIMM Interposer Probe
FS2361
-
The FS2361 is a logic analyzer probe used to test DDR3 DIMM memory. When used with the triggering and analysis capabilities of Keysight’s U4154/64 Logic Analyzer modules, it gives the user an extremely effective tool for debugging, testing and verifying DDR3 DIMMs.
-
Product
Automatic Calibration Module
ACM2509
-
ACM2509 is an automatic calibration module that can be used with all CMT Vector Network Analyzers operating in frequency range up to 9 GHz. It is a fully automatic USB-controlled and powered electronic calibration module. Minimizing the number of steps required by technicians reduces the risk of human error and expedites the calibration process. Automating the calibration routine also reduces wear and tear on the analyzer and RF cables. To perform full two-port calibration, each end of the ACM need only be connected to the analyzer once, as opposed to seven connections with a traditional calibration. The ACM also contains a factory characterized 20dB in-line attenuator which acts as a simulated device under test (DUT). The confidence check feature loads the factory stored DUT into memory so proper calibration can be verified.
-
Product
Power Calibrators And Power Quality Calibrators
-
Calmet Smart Calibration Devices
A power calibrator and a power quality calibrator are both specialized instruments used to verify and adjust the accuracy of other instruments, but they focus on different aspects of electrical power.
-
Product
High Impact Shock Test System
KRD16 series
-
High impact shock test system meets MIL-S-901D standard which covers shock testing requirements for ship board machinery, equipment, systems, and structures, excluding submarine pressure hull penetrations. The purpose of these requirements is to verify the ability of shipboard installations to withstand shock loadings which may be incurred during wartime service due to the effects of nuclear or conventional weapons.
-
Product
UVC Light Meters & Detectors
-
International Light Technologies
If you are using a UVC light-based disinfection system you are probably scrambling to deploy tools to combat the COVID-19 outbreak. Increasingly facilities are looking to disinfect everything including air, surfaces, instruments, and personal protective equipment (PPE) using UV-C light. Verifying the intensity of the light, or dose, reaching the target is a critical step in validating that the correct UV dose is being applied to ensure proper decontamination.
-
Product
Test Voltage Indicators
PRV240FS
-
Verify your test tool works without unnecessary exposure to shock and arc flash. Make the process easy by using the PRV240FS Proving unit. Verifying that your T6 electrical tester is working properly reduces the need for personal protective equipment (PPE) when a known voltage source is not available for verification before tests are performed.
-
Product
Resistive Load Banks
-
Guangdong EMAX Electrical Co., Ltd.
Resistive load banks are an important tool for testing and verifying the performance of power systems such as generators, UPS systems and turbines. They simulate real-world electrical loads by dissipating power as heat through resistive elements.
