Component
Testing of individual hardware or software components or groups of related components.
-
Product
(25kN) Fatigue Testing Systems
8872
-
The 8872 fatigue testing system is ideal for fatigue and static testing of biomedical, advanced materials, and manufactured components. The servohydraulic actuator is conveniently located in the crosshead for easy table mounting. The T-slot base makes it easy to secure orthopaedic specimens, automotive components, and manufacturing assemblies. The adjustable crosshead, actuator-mounted load cell, and corrosion resistant T-slot base with unique drain channel are essential for testing biomedical specimens immersed in a saline bath.
-
Product
Gen-Z
-
Gen-Z is a data-access technology designed to provide high-speed, low-latency, memory-semantic access to data and devices via direct-attached, switched or fabric topologies. Gen-Z components use low-latency read and write operations to directly access data and use a variety of advanced operations to move data with minimal application or processor involvement. Gen-Z fabric utilizes memory-semantic communications to move data between memories on different components with minimal overhead. Memory-semantic communications are extremely efficient and simple, which is critical to delivering optimal performance and power consumption. Teledyne LeCroy provides protocol analysis and error injection test equipment to support development and debug of Gen-Z based devices
-
Product
Precision LCR Meter 20 Hz to 300 kHz/500 kHz/1 MHz
E4980AL
LCR Meter
The E4980AL precision LCR meter is an industry standard LCR meter that provides the best combination of accuracy, speed, and versatility for a wide range of component measurements. The frequency upgrades provide a solid investment option and asset utilization.
-
Product
High-Speed Digital Image Correlation System
Q-450
-
The 3D High-Speed Image Correlation System Q-450 allows the full-field, non-contact and three-dimensional dynamic measurement of shape, displacements and strains on components and structures made from almost any material. Based on the digital image correlation technique, the Q-450 system is designed for full-field vibration analysis and high speed transient events. This makes it ideal for ballistics testing, fracture mechanics, shock excitations, the Hopkinson Bar test, or Impact Testing.
-
Product
BF-Series Soft Stop Models
-
The E-DRIV® BF-Series soft stop models is designed with an unique "soft-stop" shock absorbing clutch that is ideal for fastening shock delicate components such as disk drives, plastics, and electronics. The ergonomically designed soft stop clutch reduces impact and vibration transmitted in the screw fastening process, which delivers less torque reaction to operator. The electric screwdriver offers an adjustable speed setting and a selectable Soft Start mode. Designed for precision torque control the brushless motor design ensures durability and reduces the standard maintenance costs associated with brush type electric screwdrivers. The BF power tool is ESD certified, ensuring less than 1 Ohm at the bit tip. ESD management assures product quality, cost savings and a reduction in overall ESD failures.
-
Product
Additional Components
-
High-quality Splitter, Coupler and RF over Fibre Solutions. Made in Germany.
-
Product
Rugged Igniter Tester
4314 KV
-
Model 4314 KV is a 4-wire ohmmeter designed to use low test currents for its measurement. Additional circuitry proprietary to Valhalla Scientific is used to ensure that test current levels do not exceed the specified “fail-safe current” even in a worst-case component failure situation.
-
Product
Tools & IP
-
The Developer’s Suite is based on more than 25 years of development and continuous improvement arising from valuable customer feedback. When used together with Intel’s design tools, the Developer’s Suite provides a market-unique solution that can achieve unmatched development productivity. The Gidel Developer’s Suite includes the following components:
-
Product
Testsequencer
-
LXinstruments has many years’ experience in using both the TestStand test sequencer by National Instruments and TestExec SL by Keysight Technologies.The use of test sequencers for functional testing is crucial in order to increase productivity during the implementation and maintenance of the test software. Test sequencers make it possible to decouple the actual product-specific test sequences from infrastructure components like e. g. user interface, data storage, process interfaces and driver libraries. This ensures easy reusability of the implemented software components.
-
Product
Control Systems
-
GCA leverages decades of electronics and software experience as we build control panels and PLC software that bring machines to life and orchestrate how the machine's various components work together.
-
Product
Assesses Nodularity In Ductile Iron Cast Automotive Components
ECHOMAC® Velocity Measurement
-
Variations in Nodularity, a type of graphite structure that can develop during the production process, can attenuate the velocity of sound waves passing through the automotive component being tested. Echomac VM measures the sound velocity and, using known limits, reports whether the part is acceptable.
-
Product
Electrical Signal Test
-
High-density, multi-channel pulse pattern generators and bit error detectors for the design, characterization and production test of optical transceivers and opto-electrical components.
-
Product
Power Conversion
-
The XRP6124 is a non synchronous step down (buck) controller for up to 5A point of loads. A wide 3V to 30V input voltage range allows for single supply operations from industry standard 3.3V, 5V, 12V and 24V power rails. With a proprietary Constant On-Time (COT) control scheme, the XRP6124 provides extremely fast line and load transient response while the operating frequency remains nearly constant. It requires no loop compensation hence simplifying circuit implementation and reducing overall component count. The XRP6124 also implements an emulated ESR circuitry allowing usage of ceramic output capacitors and insuring stable operations without the use of extra external components.
-
Product
Adaptive Diagnostics and Prognostics Toolbox
ADAPT
-
The ADAPT toolbox provides advanced system health monitoring algorithms in the form of Simulink block components. These components may be used to develop health monitoring applications with the Simulink modeling tool. The applications can be tested and refined within the high-fidelity Simulink modeling environment. After verification, the Real-Time Workshop code generation tool may be used to generate deployable C language code for integration in online real-time health monitoring systems. The ADAPT algorithms provide out-of-the-box diagnostic capabilities that are applicable to a wide range of health monitoring problems.
-
Product
Combined Map Display Unit & Interface Unit Tester (COMED)
MS 1117
-
This system is used to test COMED (Combined Map Electronic Display) IFU cards. This ATE checks the LRU Status and card status and identify faulty component in the individual UUT. On fault, this suggests the possible component failure as diagnostic report, for repairing the cards.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Rapidox OEM solutions
-
At Cambridge Sensotec we have been supplying OEM gas analyser solutions for over ten years. Each OEM customer is given a bespoke scope of supply to match its exact requirements. We produce variations of our OEM electronics removing unwanted components and features to keep costs down and only give the customer the functions it actually needs.
-
Product
Hybrid Power Systems
-
UNIPOWER Hybrid Power Systems are designed to minimize power system life-cycle costs and carbon footprint. Power conversion components deliver leading efficiencies and maximum energy harvest from renewable resources using MPPT algorithms. A Hybrid Bus Architecture delivers available power from renewable resources supplemented by diesel generator or grid supply when necessary.
-
Product
Oil Content Analyzer
OCMA-550
-
OCMA-550 to measure residual oil on components and concentrations of oil adhered on solids such as soil.Measurement can be easily made only by injecting the extracted water sample into the attached cell and setting it to the equipment.This model features a simple design which allows opening/closing of the door to setting of cell with just one hand.This is best for measurement of extracted samples such as evaluation of residual oil on components and measurement of oil contained in food.
-
Product
X-ray Inspection System
RTX-113™
-
Glenbrook’s RTX-113 is designed for heavy production environments where X-ray is used to inspect PCBs and assembled PCBs containing advanced components such as BGA, micro BGA, QFN and other devices.
-
Product
Hot Swap & Hot Plug
-
Renesas offers several hot swap and hot plug controllers that enable inserting and/or removing components without interruption to a system.
-
Product
Components
-
Microwave Solutions is a worldwide leader in the design, development, and manufacture of RF and microwave components. Our broad line of components operate in the 100 kHz to 26GHz range and include Attenuators, BAW Devices, Detectors, Isolators and Circulators, Linearizers, Mixers, and VCOs. For over 50 years our components have played key roles in sophisticated airborne and satellite communications equipment, navigation and guidance systems, radar and sonar equipment, telemetry electronics, surveillance, and reconnaissance systems, and high performance commercial test equipment.
-
Product
Adapter/Gold
WADP-SFSF
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Energy Management Solutions
-
Panasonic Industrial Devices Sales Company of America
Panasonic Eco Series of Energy Consumption Visualization Components offers a wide array of products for both energy saving and power surveillance in factory automation environments. Products include Watt-Hour Meters, Power-On Counters, Power-On Hour Meter, Air Flow Meters, Communication Devices and Data Collection Units.
-
Product
Automated Test Equipment Software
-
The Emerald Software Suite allows users to control and monitor multiple test channels simultaneously. Numerous test components can be controlled from a central control station.Numerous test components, such as cooling modules, environmental chambers, loads and power supplies, data acquisition and diagnostic tools, can be controlled from a central control station.
-
Product
Video Autoselector
1154A
-
Consumers who own a receiver and/or TV with limited inputs can use the 1154A to add multiple A/V sources. Its exclusive Adaptive Signal SensingTM technology uses multiple criteria to decide when to switch sources, and adapts to users’ activity patterns, customizing its switching behavior over time. The high bandwidth circuitry accepts HDTV component video (YPbPr), stereo analog audio, and digital audio in both optical and coaxial formats, and switches all audio and video signals simultaneously when a new source becomes active. Digital audio signals are converted automatically to the desired format. Up to four sources may be connected to one receiver/video display system through the 1154A. A manual select button is provided to override the 1154A’s automatic selection. Multi-color front panel LEDs indicate source availability.
-
Product
Power Supply Units
-
converts mains AC to low-voltage regulated DC power for the internal components of a computer. Modern personal computers universally use switched-mode power supplies.
-
Product
Balanced Photo-Receivers
-
Coherent detection has been found increasing applications in fiber sensing as well as in conventional RF and optical communications. In the past several years, coherent technology has been advanced dramatically in high-speed optical communications. With this, key parts and components (such as narrow linewidth lasers, optical hybrid, balanced photo-receivers and DSP, etc.) are commercially available and cost-effective for many applications beyond telecommunications.
-
Product
Adapter/Stainless Steel
WADP-24F35F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Protection Device Testing
-
The Motwane Manufacturing Company
Power system protection is a branch of electrical power engineering that focuses on protecting electrical power systems to detect and isolate faulty parts. The objective is to keep the power system stable by separating only the defective components while keeping the rest of the network in operation. The device protects the transmission lines, generator transformer, and other electrical apparatus from multiple faults.
