Component
Testing of individual hardware or software components or groups of related components.
-
Product
Switch Assemblies
-
Dow-Key has decades of experience in space-qualified switch assemblies. These assemblies are combinations of several switches with other microwave components such as attenuator, isolator, etc.
-
Product
Objective Lenses
-
The objective lens is the most complex and the most important component in a microscope. The multi-element design of these lenses works to produce the real image, which is then seen through the ocular lens. With Olympus’ range of microscope objective lenses, we provide outstanding optical performance from visible light to near infrared.
-
Product
Drivetrain Tester
G5.DT
-
The G5.DT series is bidirectional regenerative. It was developed specifically for testing DC components of the electrical drive train or DC components of other parts of the vehicle electrical system. It is suitable for use in laboratories and on test benches. The modular and finely graded G5.DT series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies are equipped with a powerful CAN multi-protocol interface (1 kHz, 16 bit) and optionally offer test bench relevant safety functions such as PL e according to EN ISO 13849, insulation monitoring as well as automatic discharge on the load side in case of shutdown.
-
-
Product
Software For Visualizing Surface Quality
STATOVISION
-
Foerster Instruments, Incorporated
In combination with a STATOGRAPH module, the STATOVISION software enables the visualization of eddy current signals in a clearly arranged C-Scan. This results in an image of the surface quality of the components, allowing surface defects to be precisely localized. A major advantage of the STATOVISION software is the pattern recognition, which can be used for surpressing drill holes on brake discs, for example. The documentation of the entire scan is used for continuous quality assurance.
-
Product
Data Loggers
-
Identify trends in vibration, noise, temperature, humidity and more that can be indicative of component wear and/or influence machine performance with help from PCE Instruments' data loggers.
-
Product
Precision Power Analyzers
-
ZES ZIMMER Electronic Systems GmbH
Simultaneous measurement of narrow- and broadband values through innovative DualPath architectureSimultaneous capturing of fundamental frequency and broadband RMS values for instantaneous detection of losses, resp. high-frequency components
-
Product
Circbord
8019
-
VECTOR Electronics and Technology, Inc.
2-sided board, circuit pattern on both sides, holes plated thruIdeal for common busses, signal line running longer distances, for hard wire of test circuits or discrete components. Tracks run close to board edges. Solder coated pattern on both sides of board. 3U X 160mm Eurocard size will fit into 3U DIN Metric subrack.
-
Product
Electronic Components
-
We supply a wide range of components and materials to the electronics industry, such as: integrated circuits for personal computers, semiconductor materials for system LSI, optical communication materials for telecommunications, components for display devices seen in smartphones and projectors, and materials used in solar cells and lithium batteries.
-
-
Product
LXI Microwave Matrix
-
Pickering's LXI Microwave Matrix is a 2U full rack width unit that provides a compact microwave switching solution for automatic text equipment (ATE) systems. The matrix is fully configured to the specified dimensions with no extra cabling needed; saving users the cost and time of creating matrices from individual components.
-
Product
Wide Range TMAH Concentration Monitor
HE-960H-TM
-
Accurately measures the concentration of TMAH (Tetra Methyl Ammonium Hydroxide), which is the main component of the photoresist developer solutions in semiconductor manufacturing. Wide measurement range : 0 - 10 %. Have the chemical resistant carbon sensor.
-
Product
Adapter/Stainless Steel
WADP-24M29F
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
UX Usability Testing Tool
Indigo Studio
-
Your complete solution for collaborative prototyping and usability testing with video replays. Fast, code-free prototyping for today's most popular platforms. Design for mobile, web, or desktop using Indigo Studio’s built-in controls and platform environments - complete with touch and swipe gesture support. Run your prototype from any device with a web browser. Import designs from Sketch, and create reusable, interactive UI components.
-
Product
In-Circuit Tester Integration
-
The benefits of boundary-scan are noticed in all phases of a product life cycle. By coupling the power of Corelis boundary-scan tools with an In-Circuit Tester (ICT), a complete, integrated solution is available that offers the best advantages of both technologies.Boundary-scan operates as the perfect companion to ICT. Boundary-scan is capable of testing areas of printed circuit board assemblies that are difficult to access due to physical space constraints and loss of physical access, which is often due to fine pitch components such as Ball Grid Array (BGA) devices. Conversely, the ICT is able to check the non-boundary-scan compatible portion of the unit under test (UUT) such as analog.
-
Product
Linear Power Supplies
-
PeakTech Prüf- und Messtechnik GmbH
Is a component that provides power to an electrical device. The simplest design of power supply is the linear power supply, which uses a transformer and a rectifier to convert voltage from a wall outlet into the type of power the device needs.
-
Product
Power Limiters
-
Keysight's power limiters provide the best broadband input protection from excess RF power, DC transients and ESD, for a variety of RF and microwave instruments and components. For example, the input circuitry of spectrum analyzers, network analyzers, frequency counters or amplifiers can be protected from unintentional inputs up to 5 watts average power. At even greater power levels, failure mode for the limiter is either an open circuit or a short circuit to ground, thereby protecting the instrument from damage.
-
Product
Advanced Aerosol Neutralizer
3088
-
Aerosol neutralization is an important component of aerosol science and engineering. Neutralizing aerosol particles can reduce electrostatic losses of particles within tubing or to other surfaces. Neutralization is also critical to gathering reliable particle size data when using a sizing instrument based on electrical mobility.
-
Product
Engine Test Systems
TITAN Engine
-
The TITAN engine test system series contains fully equipped engine test stands which are designed for various categories of internal combustion engines, ranging from light-to heavy-duty engines and also offering solutions for component tests such as testing the exhaust line. Further adjustment for off-road engines, powered two-wheeler engines, small internal combustion engines from carts, snowmobiles or motorboats as well as aircraft turbines are available. Additionally, it is also possible to test alternative engine concepts.
-
Product
Ultra Grade SODIMM DDR4 2666/3200
SQR-SD4E
-
Ultra Wide temperature natively support -40~125C, Micron original Ultra High grade IC adopted. An underfill technique to stronger PCB and IC structural, 30u" Golden finger & Locked BOM components list. Exclusive SQ Manager software to monitor and deliver real time information.
-
Product
External Injection Module
EIM-1000
-
ATOM offers tools and accessories to meet the growing challenging needs and demands of the analytical world. The ATOM EIM-1000 External Injection Module is built for safe, fast and reliable handling of gas and LPG samples with seamless integration to the ATOM XT-2000 laboratory total sulfur – total nitrogen analyzer. The efficient and compact design reduces required benchtop space to a minimum, while allowing easy access to internal module components.
-
Product
Safety Products
-
This ACE product group provides Emergency braking to safely slow down moving loads and reduce damaging forces. Although the safety shock absorbers, TUBUS elastomer bumpers and clamping elements differ so much in design, every single ACE component provides the best protection for your machine.
-
Product
6/8/12 Volt 0-1000 Amp Heavy-Duty Variable Carbon Pile Load Tester
7136R
-
• High-volume testing and fleet use• Tests 6/12 Volt batteries• 1000 Amp load; tests batteries up to 2000 cold cranking amps• Built in LCD Digital Voltmeter and LCD Digital Amp Meter• Cools with high RPM fan for continuous battery testing• High resolution carbon pile assembly for smoother operation and longer life• Optional Model 6038C for added mobility with convenient heavy-duty cart with wheels• RoHS and CE Compliant• Made in USA of US and Global Components
-
Product
Vector Signal Generator
SMBV100B
Vector Signal Generator
The state-of-the-art R&S®SMBV100B vector signal generator sets standards for its class. Ultra high output power, fully calibrated wideband signal generation and intuitive touchscreen operation make the R&S®SMBV100B ideal for all kinds of applications.Always in line with the latest major digital communications standards, such as 5G NR, LTE and WLAN, the SMBV100B is the preferred test solution for receiver and component characterization.The R&S®SMBV100B has many GNSS options that transform the instrument into a reliable, full-featured GNSS simulator. Advanced simulation capabilities can run realistic and complex yet repeatable GNSS scenarios under controlled conditions.
-
Product
Inverted Microscope Systems
-
Below you can see examples types for an inverted microscope system created using our components. Typically these examples are for life science applications, however they can be used for industrial or material applications. Many other automated microscopy systems are possible using our components.
-
Product
Custom Compression Blocks & Spacers For Solid-State Battery Test Cells
CEP1
-
Precision-machined titanium alloy electrode posts, compression blocks, and spacers for solid-state battery test cells and electrochemical research. Available in custom sizes and configurations, these components provide stable mechanical support, reliable electrical contact, and excellent corrosion resistance.
-
Product
Satellite Components
-
Digital Signal Technology, Inc.
Various satellite components, mainly transceivers for small satellites
-
Product
Fixed Gas Detectors
700 Series
-
Teledyne Gas & Flame Detection
The sensor electronics are completely protected and immune to water ingress and corrosion. The sensor elements are all plug-in components and can easily be replaced in the field. Operator interface is non-intrusive via a small handheld magnet. Configuration and routine calibration is intuitive and menu driven with fully scripted instructions. Sensor status is displayed on a built-in alphanumeric LED display. The 700 Series intelligent sensor modules feature dual redundant outputs, a linear 4-20 milliamp analog signal and a Modbus RS-485 serial output.
-
Product
Magnetic-Field Test System
MTS-800
-
The MTS-800 is a compact test system for broadband generation and measurement of magnetic fields. Its internal components allow automatic EMC tests according to automotivestandards where high field strength need to be generatedor measured.
-
Product
TE-Metrology
-
HIGHVOLT Prüftechnik Dresden GmbH
The TE measurement complements the high voltage test and is part of the routine and type testing of numerous electrical devices. It is one of the most important non-destructive methods for detecting faults in electrical installations. The breakdown of an insulating material usually occurs at an internal weak point, which usually already shows a partial discharge activity in advance. For this reason, measuring partial discharges can help prevent costly damage. The TE measurement is thus used for quality testing and diagnosis in the factory as well as during on-site testing of cables, GIS, power transformers and transducers or rotating machinery and their components
