Leakage Current Testers
-
-
Product
DC Tester
-
The DC Tester is a Voltage and Ampere breakout for measuring DC current from 0-26V at 3.2A Max (when used with the USB Tester OLED Backpack). The DC jacks make it easy to measure a wide variety of devices by placing it inline between your power supply and your project without splicing cables, just like the
-
Product
Current Probe
PA-659
-
*Maximum Current Value: +/- 150ADC, 100A RMS*1mA = 5mA, 50mA (switchable)*Rising Time: 0.7uS*Bandwidth: DC ~ 500kHz*Over Range Indicator*Battery, AC Power Supply Adaptor (free), dual usages
-
Product
Digital Eddy Current Displacement Sensor
ZET 7140-S
-
A digital eddy current sensor consists of a primary transducer (eddy current probe) and the ZET 7140-S measuring unit.
-
Product
Dual Voltage Buffer with Current Drive
BUF-01
-
The BUF-01 Voltage Buffer is a dual channel buffer capable of driving up to 50 mA of current on each channel at up to ±10 V output. The buffer has a 2nd order low pass filter with 3 dB point of 119 kHz to remove high frequency noise. The unit’s differential inputs are built to withstand high DC over-voltages up to ±50 VDC and greater than ±100 V transients. Gain of the unit is 1 allowing for minimal insertion issues.
-
Product
Current Probe
PA-677
-
*Max. 70ADC/140Ap-p*Sensitivity: ≧2mA*Bandwidth: DC~1MHz*Rise Time: 0.35μS*Over Range Function*50mV/A, 500mV/A Range*Adaptor/Battery Input*Separating Design,Convenient Durable
-
Product
Through Hole type AC Current Sensor
CT-6S
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
For measuring current generally (through hole type)
-
Product
Franklin Tester
TF-100
-
The measuring device Franklin tester is designed to measure the insulation resistivity of coating and its mineral components on the surface of electrotechnical steel sheet as well as applied enamel to generator stator core laminations according to the ASTM A717/ A717 M - 95 Standard. The device contain series connection which allow the data transmittion to PC.
-
Product
AC/DC Current Probe, 50 MHz, 15A
1147B
Battery Probe
The 1147B is ideal for capturing transient current signals such as those found in motor controllers, switching power supplies, inverters and current amplifiers driving inductive loads.
-
Product
Semiconductor Tester
5000E
-
Current Ranges:Standard: 2.0nA – 50AUp to 100A with Mainframe ExtensionVoltage Ranges:Standard (anode): 10mV – 1000V2000V with 2kV Anode OptionStandard (gate): 10mv – 20V80V with 80V Gate Option
-
Product
HV Tester
-
For High Voltage withstand, breakdown testing of electrical insulating systems.For Dielectric Strength testing of electrical / electronic components, small appliances, tools, motors, machines etc.
-
Product
Suitable For Current Or Voltage Process Signals
SEM1600VI
-
The SEM1600VI is a “smart” powered isolator/conditioner that accepts any voltage signal between (-50 and 50) V dc or any current signal between (-50 and 50) mA
-
Product
High Voltage Non-Contact Current Probe
P02-0802
-
The TESCO High Voltage Non-Contact Current Probe (Catalog No. P02-802) was developed using current sensor technology. It is a two-piece, True RMS ammeter with a fiber optic link between the high voltage sensor and the readout at ground potential. The sensor is mounted on a hotstick and slipped over a high voltage line.
-
Product
Current Probe
LFR
-
Power Electronic Measurments Ltd
The LFR is ideal for power quality applications. It has a small, predictable phase error, for power measurements at 45/65Hz. The wide bandwidth allows accurate measurement up to and even above the 400th harmonic.
-
Product
Eddy Current Engine Dynamometers
-
A precise, low-maintenance, rapid response and repeatable alternative to water brake technology, Taylor’s Eddy Current Engine Dynos provide low-inertia, air- or water-cooled operation for testing engines up to 966 hp (720 kW) in a range of markets.
-
Product
Current Sensing Resistors: ACQ-200
TCS
-
These components are four-terminal. bus-bar, metal strip current shunts. Assembled using electron beam welding. These units can handle 15W of continuous power and a maximum current of 350A 90.1mohm). Also they can absorb a high pulse power rating and have very low inductance. They also feature excellent long term stability, less than 100ppm/C TCR, and have excellent frequency characteristics.
-
Product
MCB Tripping Current Characteristic Test Bench
-
The SCR Elektroniks 12 station MCB Tripping Characteristics Test Bench is optimally designed to verify the Tripping Characteristic of MCBs as per clause 9.10.1 of IEC 60898 (Also mentioned in Indian Standards IS 8828). The bench essentially comprises of Servo Controlled mechanism to set and maintain desired current (against incoming mains fluctuation) and a Micro controller based master controller unit plus timer, which governs the entire sequence of operation making it a stand-alone system once the user connects the MCB and configures the test parameters.
-
Product
Cable Testers
DMX ADAPTER
-
DMX protocol is a standard means of controlling lighting dimmers remotely from a control desk. The standard uses a three wire connection using 5-pin XLR type connectors. These adapters allow the E445, E446 and E447 table testers to be used to test the primary circuit of such cables. Two adapters are required for each cable tester.
-
Product
Insulation Testers
-
Kyoritsu Electrical Instruments Works, Ltd.
The insulation resistance (IR) test (also commonly known as a Megger) is a spot insulation test which uses an applied DC voltage (typically either 250Vdc, 500Vdc or 1,000Vdc for low voltage equipment <600V and 2,500Vdc and 5,000Vdc for high voltage equipment) to measure insulation resistance in either k, M or G.
-
Product
Current Transformer
ST-3RCT
-
Standard Electric Works Co., Ltd
● Primary Current Rating (Amp) : 20~300
-
-
Product
DMX Tester
DMXter4 RDM
-
The DMXter4 RDM takes the next step in protocol testing. It provides expanded DMX testing along with growing support for RDM testing and configuration. Who else would you trust to support the new standard? The DMXter4 is simple to use. Eight buttons run its menu-driven software. The DMXter4 uses a back lit 40-character display. Some functions can drive a PC using the USB port. Software updates are done via the USB port.
-
Product
Volt Tester
PPTVM01
-
The DC Voltage Tester is an easy-to-use tool that can quickly test for voltage. Perfect for testing batteries, lighting systems, trailer connections, and more. This voltage tester is self-powered with a 210 cm cable. LCD displays voltage readings from 5 volts to 35 volts.
-
Product
Cable Testers
E448
-
The EMO cable testers are designed for use in portable and bench mounted applications, including the assembly and testing of cables.
-
Product
Megger Tester
-
Shenzhen UYIGAO Electronic Technology Co., Ltd
Megger is an instrument which in addition to measurement of high resistance can be used to test the quality of the insulation.
-
Product
Gear Tester
-
MOTOMEA gear testing capabilities offer you an accurate and reliable “Gear Testing method” where you as a user can test the gear in a dynamic way, during gear acceleration period, and in a static way, by using two loading units with very accurate speed and torque sensors at the two gear sides
-
Product
LED Tester
-
Pocket-size LED tester.Easily check functionality, color, brightness and uniformity.Plug any leaded LED into one of 12 positions on the socket strip to test at current ratings from 2-50ma.The seven middle positions on the strip are set at 10 mA allowing comparison of LEDs in those spaces.Requires a 9V battery (not included).
-
Product
Integrated Current Sensors
GO series
-
*Standard package and small footprint*Cost effective*A perfect compromise for small drives, robots, solar inverters, e-bikes etc.
-
Product
Clamp type AC Current Sensor／for Load Current Measurements(CT Series)
CT-33
-
MULTI MEASURING INSTRUMENTS Co., Ltd.
*Compact size*AC 1A～200A*Current measurements of feeder
-
Product
Insulation Tester
Megohmmeter, 5kV
-
*Auto Calibration on Start-up*Onboard Battery Charger*Mains Power: 90-260Vac, 45-65 Hz*Hazardous Voltage Warning Icon > 70 volts*Test: Insulation, Voltage & Frequency
