-
product
Fastest In-Circuit Test Platform
TestStation
Teradyne’s TestStation in-circuit test systems provide electronics manufacturers with reliable high-quality, high-volume testing for the latest printed circuit board assembly (PCBA) technologies that are used in automotive, industrial, computing, consumer, communications, and defense end-products.
-
product
Dielectric Material Test Fixture
16453A
The 16453A is designed for accurate dielectric constant and loss tangent measurements on the E4991A/4291A/B. It employs the parallel plate method, which sandwiches the material between two electrodes to form a capacitor. The E4991A/4291A/B measures the capacitance created from the fixure, and option 002 firmware calculates the relative complex permittivity as described in the 16451B. Adjustment to insure parallel electrodes is required when using the 16451B. This adjustment is not required with the 16453A because the fixure has a flexible electrode that adjusts automatically to the material surface.
-
product
2-Quadrant Source/Measure Unit for Functional Test, 20 V, 1 A or 6 V, 3 A, 20 W
N6782A
The Keysight N6782A is a source/measure unit (SMU) designed specifically for advanced functional testing of a device. The ability to modulate the output up to 100 kHz along with capability to source and sink current (2-quadrant operation) makes the N6782A a perfect fit for advanced functional test of a variety of devices such as DC/DC converters, power management units, power amplifiers, and power management ICs. The input stage of the DUT can be stimulated by the fast sourcing and waveform capabilities. While the output stage can be loaded down and measured with the electronic load capabilities, providing a total test solution.
-
product
Functional Test
xUTS
Extend test to encompass copious test points and DUT varieties along with real-time, hardware-in-the-loop and other state-of-the-art instrumentation. extendedUTS (xUTS) is a custom product for high complexity functional test. Configured for the unique needs of a class of devices under test (DUTs), the xUTS employs our universal test system approach that combines the best open platform instrumentation and software along with mass interconnect technology.
-
product
Fully Automatic No Load ( Routine) Testing Panel For Self Priming Motors
Aarohi Embedded Systems Pvt. Ltd
Aarohi introduced fully automatic routine testing panel. The primary purpose of the routine test is to insure freedom from electrical and mechanical defects, and to demonstrate by means of key tests the similarity of the motor to a “standard” motor of the same design. this panel also help to enhance productivity, Work efficiency & reduces need for skill operator.
-
product
Ethernet and Fibre Channel Test Platform
SierraNet M1288
The SierraNet M1288 Ethernet and Fibre Channel test platform provides best in class analysis, jamming and generation for traffic capture and manipulation for testing application and link characteristics. SierraNet M1288 is the latest in the line of industry leading test and measurement tools from Teledyne LeCroy, designed for today’s high-speed storage and communications fabrics. SierraNet M1288 supports examination and modification of Ethernet and Fibre Channel links utilizing both Pulse Amplitude Modulation 4 (PAM4) and legacy Non-Return to Zero (NRZ) technologies.
-
product
Self Testing Clamps with Visual Indication
Bond-Rite REMOTE
As an alternative to the standard Bond-Rite, a ?remote? version is also available. In this configuration, the Intrinsically Safe monitoring electronics, flashing green LED and battery power supply are housed inside a tough, corrosion resistant stainless steel enclosure, designed for wall mounting. An insulated stowage point, for the safe return of the clamp when not in use, is included.
-
product
Self Test Application Adapter and Software
OTP2-Modul-Nr210
In order for the system to carry out a self-test, it requires a suitable adapter and software that is tailored to the test system. A self-test is often very helpful and recommended if a system has not been used for a long time or also to see whether the test system is working properly with the specified parameters.
-
product
Test Fixture, Axial And Radial
16047A
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
product
2-Module ICT System, I317x Series 6
E9902G
Keysight's family of i3070 Series 6 In-Circuit Test (ICT) systems are built on a proven technology foundation, and they improve test efficiency with time-tested software, hardware, and programmability. I3070 Series 6 ICT tester supports a wide range of printed circuit board assembly (PCBA) sizes for applications including IoT and 5G, as well as automotive and energy. The i3070 features a unique design that delivers the shortest signal path between measurement circuitry and devices under test to minimize undesired effects from parasitic capacitance, improve immunity to crosstalk, and eliminate stray signal coupling effects, delivering consistent and repeatable measurements. The Series 6 is fully backward compatible with previous systems and makes highly repeatable measurements.
-
product
Compact Automatic Voltage Regulating Relay With Built- In TPI
NMC’s Microcontroller based Automatic Voltage Regulating Relays (AVR Relays) are latest technology based Relays used for regulating the secondary voltage of Power Transformers with On Load Tap Changer (OLTC). The Parameter settings are made through the front panel keys & are stored in NVRAM. Independent time delays can be set for first control pulse & subsequent pulses. Built-in Tap displays Tap number of Power Transformer. OLTC is blocked for UV, OV, OC, CF, Min/Max Tap Positions & Tap Fail . in manual mode, Tap Raise/Lower can be achieved through front keys. In TEST mode, Relays, Display and LED indications can be checked. A pair of contacts are available for Raise, Lower, UV, OV, Manual Mode, CF, TF & OC. There are two nos. of 5 Amps C.T.’s available, one for the Over Current blocking and L.D.C. & other for measuring the Current.
-
product
Diagnostic Test Tool
BIRST™ (Built-In Relay Self-Test)
Verification and diagnosis of complex switching operation in a test system has always been an issue. BIRST (Built-In-Relay-Self-Test) diagnostic test tool provides a quick and simple way of finding relay failures available on some of our LXI and PXI switch matrices.
-
product
Conformance Test System
TS-RRM
The R&S®TS-RRM 5G and LTE test system is a test solution for running 5G NR and LTE inter-RAT RRM test cases for certification of wireless devices.It is a fully automated conformance test system for running validated RRM conformance test cases. In addition to the RRM test cases required by GCF/PTCRB, the R&S®TS-RRM also supports carrier acceptance specific RRM tests.
-
product
RSE Wireless EMC Spurious Emission
TS8996
The R&S®TS8996 RSE test system is designed for EMI and radiated spurious emission testing on wireless devices in semi-anechoic or fully anechoic chambers. The modular design makes it easy to extend the system to include new communications technologies. Typical devices under test include mobile phones or radio sets along with radiated measurements of other short-range devices. Standards require a wide range of test setups and a wide and high frequency range (up to 40 GHz). ESW or FSW frequency ranges are extended up to 325 GHz with option B21 using receive units TC-RSE for 5G FR2. Dedicated RSE test routines are also covered for this frequency range.
-
product
Purpose Built Network Packet Brokers
Garland Technology’s Purpose Built Network Packet Brokers (NPBs) are devices that provide access to network traffic from multiple links, helping to centralize and improve efficiencies by sharing packets between the monitoring and security appliances. Additional NPB features include filtering, aggregating, regenerating, and load balancing.
-
product
Test Fixture and Test Programing
Landrex Technologies Co., Ltd.
Test Fixture and Test Programing
-
product
Conformance Test System
TS8980
The R&S®TS8980 is the most compact full range conformance testing solution on the market for testing in line with requirements from GCF, PTCRB and regulatory bodies. It supports the entire device certification process for RF and RRM, covering the widest range of technologies including 5G NR based on 3GPP and carrier acceptance specifications. The test system is available in various configurations to cover the required scope of testing.
-
product
Machine Vision Computer with Built in I/O
Neousys Nuvis
Nuvis-5306RT , Nuvis-534RT, Nuvis-7306RT contain interfaces for connecting to all necessary devices: LED lighting controller, camera trigger, encoder input, PWM output and digital I / O lines.- Intel® 7th Gen Core ™ i7 / i5 65W / 35W, up to 32GB DDR4- Built-in I / O- 4-CH CC / CV backlight controller- 4-CH trigger camera- 1-CH quadrature encoder input- 8-CH isolated DI and 8-CH isolated DO- Built-in camera interfaces- 4-CH IEEE 802.3at Gigabit PoE + ports- 4-CH USB 3.1 Gen1 ports- NVIDIA 75W GPU Support
-
product
Prototyping & Test Consulting Services Solutions
Don’t cut corners on the path to quality. We are experts in Design for Test (DFT), Design for Manufacturing (DFM), agile development, prototyping and standards/best practices in many industries. Speak to our prototyping and consulting services experts to ensure you make the right decisions and investments at the start of your project.
-
product
BMS Manufacturing Test System
The Battery Management System (BMS) Manufacturing Test System performs functional testing of product during end-of-line manufacturing. The system hardware includes all instrumentation to test a BMS, including multiple cell simulators, a mass interconnect for quick product transition and bed-of-nail fixtures to ensure less down time, higher throughput, and easy maintenance. The system application easily integrates into manufacturing processes, provides a method to test multiple product types, and optimizes tests to ensure only good product is released from manufacturing.
-
product
SAP Testing
ZenQ SAP Testing Services are on-demand, providing the best testing solution for identifying application errors before they make their way into production. Enterprises normally face challenges in analyzing SAP test requirements, handling compatibility issues while configuring, customizing and integrating different modules. We help our clients ease these testing challenges by having test accelerators to bring down cost overheads.
-
-
product
Material Testing
*Abrasion Testing*Adhesion Testing*Brittleness Temp.*Bursting Strength*Coating Testing*Coefficient of Friction*Compression Testing*Compression Set*Dart Drop Testing*Density Determination*Fatigue Testing*Fiberboard Testing*Flammability Testing*Flexural Testing*Foam Testing*Hardness Testing*Heat Deflection*Hydrostatic Testing*Impact Testing*Life Cycle Testing*Melt Index Testing*Plastic Testing*Ply Separation*Resin Content*Rubber Testing*Shear Strength Testing*Stress Crack Testing*Tear Testing*Temperature Testing*Tensile/Elongation*UV Exposure*Water Absorption*Wood Testing
-
-
-
product
Pressure Testing
All metal, plastic, and composite parts intended to contain liquids or gases under pressure are required to undergo stringent pressure testing procedures to meet qualification standards.
-
product
Test Receiver
FSWT
The R&S®FSWT is the right tool for detecting compromising emanations. With two equivalent, switchable RF inputs, up to 500 MHz measurement and analysis bandwidth and two analog outputs for video voltage and demodulators, the R&S®FSWT fits perfectly into typical test setups and easily replaces older instruments.
-
product
Optical Testing
We place a great emphasis on our ability to test everything we produce and supply. This has provided the impetus for us to design and build comprehensive testing facilities that include standard as well as custom-made testing equipment.
-
product
EMC Testing
Does your product send or receive electromagnetic data? This can be analyzed using various tests. We investigate the interference immunity and emitted interference of simple electrical devices and complex machinery. Our EMC measurements and tests conducted in accordance with standards recognize all activity in the electromagnetic field and ascertain how immune to interference a piece of equipment is. We will also offer guidance on optimizing the product in terms of its EMC properties during the development phase.
-
product
EMR Testing
It is widely accepted that exposure of the human body to high levels of Electromagnetic Radiation (EMR), Electromagnetic Energy (EME) or Electromagnetic Fields (EMF) may lead to adverse health effects. To ensure the protection of personnel in the workplace and to protect members of the general public, it is essential that the EMR levels comply with relevant exposure limits set by regulators in each country.
