Discrete Semiconductor Testers
check connected individual semiconductor components.
-
Product
Impact Series Power Discrete Semiconductor Tester
-
The Impact Series Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.
-
Product
Automated Discrete Semiconductor Tester (ATE)
5000E
-
Same Proven Technology as all 5000 Series Testers. High Speed Single Test Measure. Capable of Testing Multiple and Mixed Devices. 1KV Standard, 2KV Optional. 1NA to 50A Standard, 100A Optional. 0.1NA Resolution. Complete Self Test. Auto-Calibration. RDSON to 0.1MOHM Resolution. Windows Application Software. Optional Scanner. Optional Wafer Mapping. Optional Curve Trace. MOSFET, IGBT, J-FETTriac, SCR, Sidac, Diac, Quadrac, STS, SBS Transistor, Diode, Opto, Zener Regulator, MOV, Relay. UNDER $23,000.00
-
Product
Automated Discrete Semiconductor Tester (ATE)
5300HX
-
The Model 5300HX Automated Discrete Semiconductor Tester (ATE) is designed for fast, reliable testing of a wide range of discrete devices. Using an on-board Intel SBC, can provide stand alone testing capability or connected to a PC for intuitive test development and data capture.
-
Product
MTM-Bus Tester
PXIe-1149.5
BUS Tester
The Corelis PXIe-1149.5 is a versatile, multi-mode instrument for interfacing with MTM-Bus modules. The PXIe-1149.5 adds MTM-Bus master, slave, and monitoring with full IEEE-1149.5 electrical and protocol compatibility with a standard PXIe interface for convenient integration into any Test Program Set (TPS).
-
Product
ABex PXI to Analog Bus Bridge with Digital IOs
ABex AM-300 Controller
BUS Tester
The ABex system controller ABex AM-300 is required to control the analog bus of a ABex chassis. It is used as an interconnection bridge between PXI and ABex backplane.In addition it features a whole bunch of additional functionality. Despite the 96 open drain outputs it has galvanically isolated IOs, and communication interfaces.
-
Product
Hoist Tester
Tester
The system has the capability of operating hyraulic powered hoists, DC powered hoists and 400Hz AC powered hoists. When a unit is connected to the system it is automatically detected and the system will load the unit's control software, acceptance procedures and operational safety limits. By doing all of this the operator does not need to worry about anything other than installing the unit and clicking Run to execute a full test procedure.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
PAM4 Bit Error Rate Tester.
BERT-1102
Tester
The BERT-1102 is a 4 or 8-channel PPG and Error Detector for the design, characterization and manufacturing test of optical transceivers and opto-electrical components with symbol rates up to 29 GBaud/s in both NRZ and PAM4 formats. With scalability and exceptional signal fidelity, it is a cost-effective test solution for up to 400 Gb/s communication eco-systems.
-
Product
Universal A/V Tester
Tester
This tester was built for our client with the specific requirement that specific UUTs can be added to the system by our client. We handled developing test software for the first 2 UUTs utilizing an open programming structure that allowed programming modules to be strung together to create test programs for any additional UUT that our client wants to add in the future.
-
Product
Gearbox Tester
Tester
The gearbox tester was designed to test the Azimuth Drive Unit (ADU) for a missile launcher. The ADU is the horizontal position controller for the launcher. It consists of a main drive shaft, a manual drive shaft and an output drive shaft. This system uses a multi-axis motion controller to operate.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
KVS Rugged Igniter Tester With Current Monitor
4314
Tester
The Valhalla Scientific Model 4314 KVS Digital Igniter Tester is designed to provide extremely safe and reliable resistance testing of explosive or volatile devices. Proven uses include fuses, squibs, igniters, explosive bolts, automobile airbag initiators and many others.
-
Product
Automated Coherent Receiver Tester
CoRx Tester.
Receiver Tester
Quantifi Photonics’ CoRx Tester provides automated measurement of key coherent receiver performance parameters. The CoRx Tester is comprised of a pre-configured PXI chassis, a two-channel tunable laser, a polarization controller, and a two-channel Variable Optical Attenuator (VOA) with built-in power meter. Just connect the two optical outputs to your Integrated Coherent Receiver (ICR), connect your ICR to the oscilloscope and let the CoRx Tester software do all the rest.
-
Product
Open/Short Tester for Reverse Engineering Applications
Panther 2K-CT
Tester
Qmax Test Technologies Pvt. Ltd.
Panther 2K-CT is a versatile open\Short tester designed especially for reverse engineering application of tracing circuits of undocumented PCBA’s.Its innovative measurement technology helps tracing PCB tracks between components in a given circuit board. It can accommodate various types of clips\grabbers and connectors to access the device pins to trace the connectivity. Its user friendly software guides the user to place and move cluster of IC clips and probes to learn the connectivity and to generate netlist.
-
Product
Semiconductor Testers
-
Designing and manufacturing scalable Automated Test Equipment (ATE) targeted at testing SOC, MCU, RF PA/FEM, Sensors/MEMS and Power and Analog devices
-
Product
Semiconductor Device Testers
-
are particularly suitable for certain semiconductor test requirements, but other models may also be of interest. Our knowledgeable application engineers can guide you to the most suitable model.
-
Product
Semiconductor Thermal Transient Tester
T3Ster®
-
T3Ster (pronounced "Trister") is an advanced thermal tester from Mentor Graphics MicReD Products for thermal characterization of semiconductor chip packages. Superior to all other thermal characterization equipment on the market due to its speed and ease of use; its extremely accurate temperature measurements (0.01oC); and its 1 micro-second measurement resolution in time.
-
Product
Semiconductors
-
Meets SDIO card v2.0 specificationSupports SDIO SPI, 1-bit, and 4-bit SD modesHost clock rate from 0-50 MHzSingle SDIO function interfaceSD commands processed in hardwareReset output on completion of initializationIndication of high speed and high power enabling to application logicMaximum block size supported is 1024 bytesThree I/O mode selection pinsCRC7 and CRC16 modulesSupports direct R/W (IO52) and extended R/W (IO53) commandsAPB bus interfaceParallel bus interfaceStandard 8051 split bus interfaceGeneric 8051 bus interfaceUART interface
-
Product
High Volume Semiconductor Substrate Interconnect Tester
GATS-2100
-
Pre-align *load *CCD camera alignment *electrical test * unload * sort of pass, opens, shorts, and alignment errors.The GATS-2100 concurrent approach provides unmatched volume capability... 2.5 seconds per device. As with all Nidec-Read Test systems, the GATS-2100 offers you the most test technologies for your requirements
-
Product
Semiconductor
-
Engineered ceramics are used in the semiconductor industry because of their excellent material properties. Ultra-pure ceramics are often used in the whole cycle of semiconductor manufacturing including Semiconductor Wafer & Wafer Processing, Semiconductor Fabrication (Front End), and Semiconductor Packaging (Back End).
-
Product
Discrete Detectors
-
TRAL test station is a quasi-universal test station designed to measure parameters of discrete (or small linear array) infrared detectors sensitive in a wide spectral range from about 700nm to about 16 000 nm (NIR/SWIR/MWIR/ LWIR detectors or broadband non selective detectors). All main types of infrared detectors can be tested: photonic detectors: photovoltaic/photoreconductive, cooled/non-coooled, thermal detectors, pyroelectric detectors etc.
-
Product
Compound Semiconductor
-
Scientific Computing International
Semiconductors that are made from two or more elements.
-
Product
Semiconductor Assembly
-
With the know-how that we have cultivated over many years in the semiconductor manufacturing process, we respond to the diverse needs of our customers regardless of prototype production and mass production.
-
Product
Semiconductor Test
-
Smiths Interconnect’s test socket and probe card solutions utilize IDI contact technology to ensure superior quality and reliability in semiconductor test applications. Our best-in-class engineering, development and technical expertise ensure support of automated, system level and development test platforms.
-
Product
Semiconductor Testers
Test Instrument
Our integrated team of semiconductor test innovators delivers a complete system tailored to achieve your specific objectives, incorporating:Test strategyHardware designSoftware development and integrationManufacturingInstallationProgram managementOngoing support
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Benchtop Discrete Component Tester
Imapact 7BT
-
The 7BT Benchtop Discrete Component Tester is designed to test small signal and power semiconductor components in both single and multi-device packages or hybrids.. The 7BT automatic test system can be used in all test applications including incoming inspection, wafer probe, QC, engineering, production, final test, and high reliability.
-
Product
Semiconductor Laser
-
Fibre coupling semiconductor laser. The product range of wavelengths is 450nm~1550nm. The product range of power is 2mW~300W. A Variety of package coupling form,can be integrated indicator light,a photoelectric detector, a semiconductor refrigerator, optical switch function. Solution of flexible and diverse, providing customized service sub system.
-
Product
16-CH Discrete Input 16-CH Discrete Output Module
HSL-DI16DO16-M-NN
Input/Output Module
- Input voltage: ±40 V (Max)- Output switching capacity: Single channel 500 mA; all channels 60 mA at 24 VDC- Photo couple isolation voltage: 2500 Vrms- Input impedance: 4.7 KΩ- Input current: ±10 mA (Max) , ±12.5 mA (Peak)- 16-CH digital input and 16-CH digital output. "NN" type for NPN sinking type sensor input or dry contact and NPN sinking type output- Slave ID consumption: 1
-
Product
Semiconductor CharacterizationSystem
Keithley 4200
-
Materials Development Corporation
The MDC CSM/Win-4200 System integrates the extraordinary power of the CSM/Win softwarewith the power of the new Keithley 4200-SCS. Measure capacitance, voltage, and current down to sub-femtoamp levels.
