Polarization Extinction Ratio
a measure of the degree of polarization. Also known as: PER
See Also: Fiber Optic Cable Test
-
Product
Oxygen Sensor Tester and Simulator
ST05
-
The sensor signal output is shown in real time on the bar graph, while a 2 digit alphanumeric display shows the sensor output cross count per second. By pressing the ?Test? button and performing a snap throttle acceleration of the engine, it tests the response time of the sensor and shows a pass or fail result within seconds. Two buttons allows for simulation of rich or lean conditions to monitor response of the engine control module.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1Ω to 239Ω
40-253-113
Programmable Resistor Modules
The 40-253-113 is a programmable resistor module with 1 channel which can be set between 1Ω and 239Ω with 1Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
Pulse Function Arbitrary Noise Generator
81150A
Arbitrary Waveform Generator
1 - 120 MHz pulse generation with variable rise/fall time1 - 240 MHz sine waveform output14-bit, 2 GSa/s arbitrary waveforms512k samples deep arbitrary waveform memory per channel Noise with a selectable crest factor and signal repetition time of 26 days FM, AM, PW, PWM, FSK modulation capabilities up to 10 MHz1 or 2 channel, coupled and uncoupled Differential outputs
-
Product
iSocketTM - High Power DUT - HTOL System
8000 Series
-
iSocketTM Technology Open Rack-Room Temperature (RTBI) non chamber design High Power DUT Capability – 0-65W Individual DUT Temperature Measurement & Control DUT Monitoring with Auto shut down 28 BIB capacity – 14 trays 2 BIB’s per tray Multi DUT type HTOL Testing Remote System & HTOL Monitoring – Customer access via VPN
-
Product
USB/RS232/SPI Programmable Attenuator
RUDAT-13G-90
-
Mini-Circuits’ RUDAT-13G-90 is a general purpose programmable RF attenuator supporting frequencies from 10 to 13000 MHz with attenuation from 0 to 90 dB in 0.5 dB steps. Its unique design maintains linear attenuation change per dB, even at the highest attenuation and frequency settings. The attenuator is controlled via USB, RS232 or SPI. It comes housed in a compact, shielded metal case with SMA(F) input/ output RF ports (RF ports are interchangeable), a USB type Mini-B socket, and a 9-pin D-sub(F) RS232 and SPI port. Power can be supplied via either USB or the D-sub port. The RUDAT-13G-90 is supplied with our easy-to-install, user-friendly GUI software, API objects for Windows® environments, and complete programming instructions for 32 and 64 bit Windows® and Linux® operating systems. See p. 9 for a complete list of included accessories.
-
Product
14-bit, 125 MS/s Waveform Digitizer
ATS9146
-
ATS9146 is a 2-channel, 14-bit, 125 MS/s waveform digitizer capable of storing up to 128 Million samples per channel of acquired data in its on-board memory or streaming acquired data to motherboard memory. ATS9146 is a single-lane PCI Express (PCIe x1) Gen 1 card, which supports up to 200 MB/s bus throughput. ATS9146 is an ideal solution for many applications.
-
Product
Isolated LVDS
-
Isolated LVDS (low voltage differential signaling) devices couple differential signals applied to the LVDS receiver inputs across the isolation barrier to the outputs on the other side and re-transmits the bit stream or clock as LVDS. Analog Devices' drop-in LVDS isolators offer designers robust, high speed differential signaling for point-to-point and multidrop applications. Extending iCoupler® chip scale transformer technology for ultrahigh speed data encoding, these LVDS isolators support a a data rate of up to 2.5 Gigabits per channel for a total bandwidth of 10 Gbps. In contrast to expensive fiber implementations, deserialized links over standard digital isolators or optocouplers, and design-intensive bespoke solutions using transformers or high voltage capacitors, ADI Gigabit Digital LVDS isolators offer the only integrated comprehensive, high performance isolation at 10 Gbps. High performance galvanic isolation for applications include analog front-end (AFE), processor to processor serial communication, or video and imaging data (such as HDMI isolators) as well as isolation between boards, or at a cable interface for LVDS or CML signal chains.
-
Product
Get Flexible, Get FlexiFLASH
LatticeXP2
-
*Up to 885 Kbits sysMEM™ embedded block RAM and up to 83 Kbits distributed RAM*sysCLOCK™ PLLs up to four analog PLLs per device that enable clock multiply, divide and phase shifting*Three to eight sysDSP blocks for high performance multiply and accumulate.*Pre-engineered source synchronous IOs for DDR/DDR2 up to 200 MHz and 7:1 LVDS interface support up to 600 Mbps*Available in csBGA, TQFP, PQFP and BGA packaging
-
Product
Network Sensor Interface for USB Pressure Transducers
SI314
-
The Validyne model SI314 is a network interface that connects our model P61 USB pressure Transducer to your smart phone or network web browser. The SI314 supports Ethernet and Wi-Fi connections and will display current pressure readings and transducer status on any web browser or via smart phone. The SI314 also displays the transducer temperature, date of calibration, model and serial numbers and these can be viewed wirelessly or by Ethernet connection. The SI314 makes your P61 accessible from anywhere in the world. Data logging of pressure data is configured via a web browser or smart phone and readings may be stored once per minute to once per hour. A thumb drive or memory card collects the data in comma separated file format(csv) for download to your computer. The data may also be accessed via the network. A graph of the data is also generated on request. A Twitter function allows pressure data to be tweeted from the SI314 at user-defined intervals. The transducer zero and span calibration adjustments are password protected and operated via browser buttons. No potentiometer adjustments are required to calibrate the P61 transducer. Contact our Sales Department for a link to the Demo!
-
Product
LXI Optical Switching - 8:1 Multiplexer Plugin Module
65-281-323
Multiplexer Module
The 65-281-323 8:1 multiplexer is part of the 65-280 and 65-281 ranges of optical plug-in modules offering matrix & insert/bypass or multiplexer & SPST topologies respectively with all models based on MEMS fiber optic switches and available in various populations per plugin. In addition, a choice of different connector styles to suit most applications is offered: FC/APC (for optimal performance), FC/PC, SC/PC and ST for general applications and LC for high density applications. They use MEMS (Micro-Electro-Mechanical-Systems) based optical switches to route signals between terminals by redirecting the optical signal. This is achieved using micromechanical mirrors driven by a highly precise mechanism activated via an electrical control signal.
-
Product
IBM PC-XT, Vectorbord Plugbord
4613-3
-
VECTOR Electronics and Technology, Inc.
62 contacts (31 each side) on 0.100" centers. Pad per hole. Voltage and ground buses around board perimeter. I/O mounting area for 37-pin D-sub and ribbon cable connectors. Mounting bracket and hardware kit included (P/N HD36B).
-
Product
PXI 5W Programmable Resistor Module, 1-Channel, 3Ω to 11.4MΩ
40-252-053
Programmable Resistor Modules
The 40-252-053 is a programmable resistor module with 1 channel which can be set between 3Ω and 11.4MΩ with 1Ω resolution The 40-252 range provides a simple solution for applications requiring up to 5W of power handling per channel. The 40-252 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
Static Frequency Converter Systems with Built-in Isolation System
FC3X Series
-
- VFI independent output as per IEC62040- User friendly controls and indications- Compact design with inbuilt transformer- Rugged and field proven for Industrial and Defence application- Ultra light weight- Higher efficiency of operation means significantly lower running costs- State of the art IGBT based PWM technology, to increase crest factor tolerance & dynamic stability- Continuously delivers full output power at ambient as high as 45ºC- Can feed upto 400% rated current for half cycle- Very high MTBF
-
Product
Density & Specific Gravity
-
To maintain consistency of a coating, the Density should remain constant from batch to batch. Density Cups, also known as Specific Gravity Cups or Picnometers, are used to determine the mass per unit volume (Specific Gravity) of a liquid at a given temperature. Specific Gravity is defined as the ratio of the density of a given substance to the density of water, when both are at the same temperature. As the Specific Gravity Cup is an exact measurement of the volume of the liquid, it is imperative that the exact weight of the sample is obtained.
-
Product
2-CH PCI Express® 10 GigE Vision PoE+ Grabber
PCIe-10GPoE
Frame Grabber
ADLINK's PCIe-10GPoE PCI Express® PoE+ frame grabber supports 2-CH independent Gigabit Ethernet ports for multiple GigE Vision connections transferring up to 10Gb/s per port. PoE+ provides up to 30W power and automatic detection for stable, reliable connections, reducing costs, simplifying installation, and easing maintenance burdens. Exclusive comprehensive PoE Protection secures assets prevents overcurrent and overvoltage avoiding equipment damage. Smart PoE Management, easy-to-use utility and API provide realtime PoE status monitoring and control, lowering maintenance costs and predicting possible failure in advance. ToE (Trigger Over Ethernet), FPGA-based Trigger over Ethernet synchronizing multi-camera acquisitions significantly reduce ownership costs.
-
Product
Xeon E3 Processor, 10GbE, MTCA.4, Double Module, AMC
AMC725
-
The AMC725 is a Processor AMC (PrAMC) in a MTCA.4 double-module, mid-size AMC form factor. It features an Intel® Xeon E3 Processor with Cave Creek PCH, and on-board dual RAID options. The module provides PCIe Gen3 x4 or single x8 on ports 4-11 per AMC.1, dual GbE on ports 0 and 1 per AMC.2, and SATA on ports 2 and 3 per AMC.3. Dual 10 GbE ports are included on the front panel.
-
Product
Long-Range, High Resolution Target Detection Radar
Ranger® R20SS
-
The Ranger® R20SS is a ground and coastal surveillance radar specifically designed to detect and track personnel and vehicles within a 20-km range. With its solid-state electronic scanning capability and fast 2-Hz refresh rate, the Ranger R20SS delivers best-in-class target detection and acquisition performance. Because it operates in the X-band, R20SS is minimally affected by adverse weather or precipitation. It scans a +/-90° area twice per second with low false alarm rate.
-
Product
High Speed Spectroscopy Camera
SynapsePlus CCD
-
Superfast electronics (up to thousands of spectra per second). Very low read noise. Best linearity in its class. Different chip types to suit every spectroscopy need. Open Electrode (OE) 1024 x 256 pixels, Front-illuminated UV enhanced (FIUV) - 2048 x 512 pixels, Front-illuminated visible (FIVS) - 2048 x 512 pixels, Back-illuminated UV enhanced (BIUV) - 1024 x 256 and 2048 x 512 pixels, Back-illuminated visible (BIVS) - 1024 x 256 and 2048 x 512 pixels, Back-illuminated deep depletion (BIDD) – 1024 x 256 pixels.
-
Product
PXI/PXIe 15W Programmable Resistor Module
40-254-014
Programmable Resistor Modules
The 40-254-014 (PXI) and 42-254-014 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 470Ω with 2Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
IRIG Time Code Receiver & Generator Module
TCR180
-
Meinberg Funkuhren GmbH & Co. KG
The module TCR180 has been designed to receive and to generate IRIG-A/B/G, IEEE 1344, IEEE C37.118 or AFNOR NF S87-500 time codes. It is used in applications like data acquisition, standalone computer time synchronization (for systems without a network connection or higher accuracy requirements) or as an IRIG converter device. The frequency locking of the master oscillator to the time code system enables this module to generate fixed and programmable standard frequencies with high accuracy and stability. Various oscillator options allow the cost efficient implementation of different requirements concerning the accurracy of the outputs. The generator of the IMS-TCR module generates pulses per second and per minute and per hour. Four programmable outputs are also available. The pulses are synchronized to UTC-second.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 31.5Ω
40-251-010
Programmable Resistor Modules
The 40-251-010 is a programmable resistor module with 8 channels which can be set between 1Ω and 31.5Ω with 0.125Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
3 Axis Digital Fluxgate Vektor Magnetometer
WFG-D-140
-
The Model WFG-D-140 Sensor is a tri-axial vector magnetometer system with a high-speed digital interface that can transmit XYZ magnetic field values at up to 140 times per second. The WFG-D-140 System contains a microprocessor and a three channel 16-bit analog-to-digital converter. The system also contains a temperature sensor.
-
Product
PMC Module
PMC-softDAC
PMC Module
2 µS settling time, 0-5v range• Six Programmable OutputRanges per channel• Unipolar: 0V to 5V, 0V to 10V• Bipolar Mode: ±5V, ±10V,±2.5V,–2.5V to 7.5V• 1LSB Max DNL and INL Over theIndustrial Temperature Range• 64k DAC buffers• Power-On Reset to 0V• Flash ram for configuration file• Two stage buffers• Global output buffer w/ internal orexternal triggering
-
Product
Clamp on Meters
-
2000 counts LCD displayData hold for easy readingAuto-power offSafety as per IEC1010-1, Cat.II 1000V
-
Product
16 A/D Channels (±1.25 to ±10.0 VDC FSR or ±25 mA) ; 16-bit SAR, 8 Chx2 A/D multiplexed
AD4
-
Module AD4 features 16 channels with up to 16-bit SAR A/D converters for one per 8 channel multiplexed bank / 2 banks. The maximum programmable, expected full-scale range input for the AD4 module is ±10.00, ±5.00, ±2.50 or 1.25 volts where range is -FS to +FS, 0 to FS VDC, or ±25 mA. The A/D converters have programmable sample rates of up to 500 kHz / Aggregate per bank of 8 Channels.
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function DAQ Cards
DAQ-2500 Series
-
ADLINIK DAQ-2501 and DAQ-2502 are high-speed and high-performance analog output multifunction DAQ cards. The devices are able to update up to 8-CH, 12-bit analog outputs simultaneously at sustaining 1 MS/s. The reference sources and the output polarities are programmable on per channel basis, combining with the multiplying DAC architecture, ADLINK DAQ-2500 series DAQ cards can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees the CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The DAQ-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
HandyScope HS6-DIFF With SureConnect: 200 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-200XMS-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
-
Product
18-Slot 3U 24GB/s PXI Express Chassis – Up to 8 GB/s, 50W Power and Cooling Capacity Per Slot
PXES-2785
Chassis
The ADLINK PXES-2785 chassis combines a high-performance 18- slot PXI Express backplane with a high-output power supply and a structural design that has been optimized for maximum usability in a wide range of applications. The chassis' modular design ensures a high level of maintainability and offers replaceable power supplies for high-availability applications, resulting in a very low mean time to repair (MTTR). The PXES-2785 chassis fully complies with the PXITM-5 PXI Express Hardware Specification, offering advanced timing and synchronization features.
-
Product
PXIe/CPCIe Data Storage Module
Trifecta-SSD-RAID
-
Trifecta-SSD Modules feature a PCIe Gen 3 x8 interface and a unique architecture that supports up to eight (8) M.2 NVMe SSDs in a single slot which enable the modules to sustain up to ~7 GB/Sec sequential read and write performance without incurring the write “hiccups” or “glitches” that plague other RAID Modules with only four SSDs. This capability is essential for systems that stream 1+ GHz bandwidth per channel for long durations.
