Polarization Extinction Ratio
a measure of the degree of polarization. Also known as: PER
See Also: Fiber Optic Cable Test
-
Product
Waveguide Bends
-
Fairview Microwave’s lines of precision waveguide bends are widely used in applications such as high efficiency RF, microwave and mm-wave transmissions, satellite and military communications, radar, telecom, instrumentation and test benches. In waveguide systems that require a signal to turn or bend 90 degrees, Fairview’s waveguide bends are used to facilitate that bend or turn without degrading the transmission signal. These WG bends operate from 5.85 GHz to 90 GHz across 12 frequency bands and are available in sizes from WR-12 to WR-137. This family of waveguide bends also boast low loss and VSWR as low as 1.08:1 and are available in both E-plane and H-plane configurations. They are constructed using gold plated, oxygen free hard copper (OFHC) or painted copper alloy depending on the model and are also offered with either a UG-style flange per the military standard or a CPR-style flange. Many models are RoHS compliant.
-
Product
6-Ch Voltage Analog Input EtherCAT Slice IO Module
AMAX-5017V
EtherCAT Slice IO Module
Channels : 6 (Differential)Input Type : V,mVVoltage Range : ±150 mV, ±500 mV, ±1V, ±5 V, ±10 VInput Impedance : >10M ΩResolution : 16-bit with ±0.1% FSR accuracySample Rate : 100 sample/s (per channel)
-
Product
PXI 2.5W Programmable Resistor Module, 4-Channel, 2Ω to 52.4kΩ
40-251-033
Programmable Resistor Module
The 40-251-033 is a programmable resistor module with 4 channels which can be set between 2Ω and 52.4kΩ with 1Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
SIMULATOR
458-LM-A8-18A
-
Simulates 26 AWG PIC as specified in ANSI T1.417Bandwidth DC to 18 MHzIdeal for testing ADSL, ADSL2, ADSL2+, ADSL2++, VDSL,VDSL2(supports up to Profile 17a) modems/DSLAMs8 channels per line moduleLoop lengths programmable from 0 to 15,000 ft in 1,000-ft incrementsPlugs into our Model 458-CC-16 (16-slot) or 458-3SLB (3-Slot)chassisChannel-to-Channel isolation up to 90 dB
-
Product
Gas Leak Detector
Gasurveyor 500
-
Teledyne Gas & Flame Detection
The Gasurveyor 500 is the most flexible range of gas detectors available from GMI. By simple selection of hardware and software options, the instrument can be readily configured to suit your exact application. Offering highly accurate and reliable instrumentation in an extremely robust, anti-static case, the Gasurveyor 500 Series measures gases common in many applications.Any combination of flammable gas from parts per million (ppm) through Lower Explosive Limit (LEL) to percent volume, oxygen, carbon monoxide and hydrogen sulphide can be selected to ensure that your exact requirements are met. All of the Gasurveyor 500 Series are dual mode instruments, making them suitable for both surveying work and confined space.
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-033
Programmable Resistor Module
The 40-254-033 (PXI) and 42-254-033 (PXIe) are programmable resistor modules with 1 channel which can be set between 2Ω and 52.4Ω with 1Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
PXI 2.5W Programmable Resistor Module, 8-Channel, 1Ω to 62.1Ω
40-251-011
Programmable Resistor Module
The 40-251-011 is a programmable resistor module with 8 channels which can be set between 1Ω and 62.1Ω with 0.25Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems. Each channel is able to simulate short or open circuit conditions that can be experienced in a system caused by faulty wiring or sensors.
-
Product
COM Express Type 10 Reference Carrier Board
miniBASE-10R
Carrier Board
The COM Express approach of custom carrier combined with off the shelf system cores is an excellent solution when you need to customize but lack the time or quantity for a complete redesign. It fits most system integration projects with production volumes from 500 to 10,000 pcs per year. The COM Express concept has a great many advantages over full custom designs, it reduces engineering complexity, lowers the threshold for total project quantity and last but not least brings your product to the market in no time. The average time to design a carrier board is less than half the time of a full custom OEM board.
-
Product
EasyMatrixCode
-
Automatic detection of the code in the imageDecodes ECC200, ECC000, ECC050, ECC080, ECC100 and ECC140 codesComputes quality indicators as per ANSI/AIM, ISO/IEC 15415, ISO/IEC TR 29158 and SEMI T10-0701 standardsVery fast operationImpressive robustness to noise, blur and distortionSupport of GS1 Data Matrix codesEfficient reading of codes in grid layoutMultiple codes reading
-
Product
PXI/PXIe 15W Programmable Resistor Module
42-254-013
Programmable Resistor Module
The 40-254-013 (PXI) and 42-254-013 (PXIe) are programmable resistor modules with 2 channels which can be set between 1Ω and 238Ω with 1Ω resolution The 40-254 range provides a simple solution for applications requiring up to 15W of power handling per channel.
-
Product
Industrial Gaussmeter
-
The industrial gaussmeter IGM11 is used to measure magnetic DC and AC fields. The measurands are flux density in Tesla or Gauss and the field strength in Amps per meter.
-
Product
Data Logging System
SPARTAN
-
SPARTAN is an affordable, compact multi-channel measuring system specially designed to optimize potential-isolated measurement of voltage and temperature. With a sampling rate of up to 10 kHz per channel, even highly dymanic processes can be recorded with high resolution.
-
Product
PXI 2.5W Programmable Resistor Module, 1-Channel, 3Ω to 5.82MΩ
40-251-152
Programmable Resistor Module
The 40-251-152 is a programmable resistor module with 1 channel which can be set between 3Ω and 5.82MΩ with 0.5Ω resolution The 40-251 range provides a simple solution for applications requiring up to 2.5W of power handling per channel. The 40-251 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
USAF Targets
-
These targets conform to MIL-STD-150A. Frequencies change by the 6th root of 2. This target is also available in custom sizes and contrasts. This test target meets requirements as specified in MIL-STD-150A for resolving power tests. The target consists of a series of Elements having two sets of lines at right angles. Each set of lines consists of three lines separated by spaces equal to the line width. Each bar has a length to width ratio of 5:1. (Line width is equal to one half of line pitch, which is the inverse of line frequency.) Elements are arranged in groups of six each and Groups are arranged in pairs. Even numbered Groups occupy the left side and bottom right corner and contain a square feature having and edge length equal to the line length of Element 2 in that group. Odd numbered Groups occupy the top right corner and side. Groups and Elements are labeled and differentiated by numbering adjacent to their features. Frequencies in cycles/mm (c/mm) increase between each Element by the sixth root of two (approximately 12.25% per step). The general formula for the line frequency of any target Element can be expressed as 2Group+(Element-1)/6.
-
Product
Mixed-Signal Active Load Pull System
MT1000 And MT2000 Series
-
The MT1000 and MT2000 mixed-signal active load pull systems are the best commercially proven solutions capable of performing load pull at high speeds of up to 1000 impedance/power states per minute with no limitation on Smith Chart coverage, under the following conditions:Single-tone CW and pulsed-CW RF signalDC and pulsed-DC biasTime-domain NVNA voltage and current waveforms and load linesFrequencies between 1 MHz and 40 GH
-
Product
RGB Video Driver
PCI900
-
The PCI900 is a PCIe form factor module that has dual RGB analog video receiver inputs. It outputs two analog RGBs that provide the capability to drive UXGA video up to 110 feet over coaxial cable. The input impedance is 75 ohms with a signal level of 1 VPPper RS-343A with sync on green. The output characteristic being 1 VPP into 75 ohms per RS-343A which can drive a minimum of 110 feet of cable.The PCI900 receives only power from the PCIe bus and has no other connection to the PCIe bus.
-
Product
Oxygen Bomb Calorimeters
-
Labodam oxygen bomb calorimeters are designed with high precision sensors and microprocessors to get reliable and accurate results. They are designed and made as per the International Standards ASTM D5865-13 Test Methods for Heat of Coal, ASTM D240-17 Test Methods for Calorific Value of Petroleum Products, and ASTM D4809-13 Oxygen Bomb Calorimeter.
-
Product
DC Power Supply
-
A DC power supply is an instrument that produces a pure, stable DC power supply. There are several important parameters when choosing a DC power supply, including the number of channels, total power, output specifications per channel, resolution, and so on. Each indicator is related to the needs and applications we actually test.
-
Product
VXIbus Universal Power Meter
58542
-
The Model 58542 provides faster CW measurements than any other VXIbus power meter, with readings over the GPIB exceeding 150 readings per second and an exclusive Burst Mode capturing more than 5000 readings per second.
-
Product
Vehicle Testing
-
short testing times, thereby enabling a large throughput of vehicles;objective, operator independent test results on most test items;accurate measurements;a large set of clear user instructions is displayed, which allows the owner/ driver to stay in the vehicle during the test, thus saving manpower;a wide selection of different test equipment for integration is available;a large number of settings, threshold values and standards can be accessed directly and edited by the user;the modular setup allows a complete variety of Test Lane configurations;easily upgradable by adding more test equipment items per lane;easily expandable by adding more Test Lanes;integration of Test Lanes on remote sites is possible;link up to Government database and remote access possibilities where applicable.
-
Product
PXI 10W Programmable Resistor Module, 1-Channel, 1.5Ω to 925Ω
40-253-021
Programmable Resistor Module
The 40-253-021 is a programmable resistor module with 1 channel which can be set between 1.5Ω and 925Ω with 0.25Ω resolution The 40-253 range provides a simple solution for applications requiring up to 10W of power handling per channel. The 40-253 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
Product
Dual-Channel, Tri-port per channel, for extended cabling up to 4.5 meters
FW2
-
The FW2 provides IEEE 1394 (Firewire) high-speed serial communications. The module is provided with a direct PCIe interface to the local (on-board) processor, or, an external host processor for board platforms that support external PCIe connectivity. These module(s) are not supported with the classic memory register-based NAIBrd Software Support Kit (SSK) API libraries. These communication function modules support device control and management via standard native OS (Linux) FireWire device driver.
-
Product
2-port 10GbE PoE PCI Express Card
AX92324
-
Intel® Ethernet Controller X550-AT2, up to 10 Gbps data rate, Supports 15.5KB Jumbo Frame and IEEE 1588, Compliant with IEEE802.3at to deliver 25.5W per port, PCI Express x4 compliant, PoE power on/off via Power Manager software and API, Operating temperature range from 0°C to 55°C
-
Product
USB-7855, Kintex-7 70T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device
782915-01
Multifunction Reconfigurable I/O
Kintex-7 70T FPGA, 1 MS/s Multifunction Reconfigurable I/O Device - The USB‑7855 features a user-programmable FPGA for high-performance onboard processing and direct control over I/O signals for complete flexibility of system timing and synchronization. You can customize these devices with the LabVIEW FPGA Module to develop applications requiring precise timing and control such as hardware‑in‑the‑loop testing, custom protocol communication, sensor simulation, and high-speed control. The USB‑7855 features a dedicated A/D converter per channel for independent timing and triggering. This design offers specialized functionality such as multirate sampling and individual channel triggering, which are outside the capabilities of typical DAQ hardware.
-
Product
Ultra Low Level DC Voltage Amplifiers
-
The EM A10 is a low level amplifier module for sensitive measurements, data collection and systems, where signals below 1 nanovolt may be measured. It is ideal for the input unit for precision voltage measuring systems, requiring voltage sensitivity for measuring low noise and low impedance sources. The noise level of the A10 is equivalent to a perfect resistor of about 20 ohms. When used with a digital voltmeter, steady one nanovolt digits may be displayed, with a response time constant of less than a second. The input voltage stability of the A10 is very high, with the drift around a nanovolt per degree C. The input connectors are made from pure copper. The input impedance is very high, and is time dependent, determined by the loop gain.
-
Product
Software for Configuration, Logging and Analysis
LMG-CONTROL
-
ZES ZIMMER Electronic Systems GmbH
Real-time display of configuration and measuring valuesTransfer of up to 3000 measuring values per secondTimestamps with a resolution of 1 millisecondVersatile analysis of sampling valuesExport of measuring values to other applications
-
Product
Avionics System Power
58WS1-03
-
- 3Ø AC input per MIL-STD-704A- 1,500 Watts continuous, 3,000 Watts peak power- Environmentally sealed ATR style case- Continuous Background Built-In-Test (BIT) and ETI- EMI compliance
-
Product
DC to 350 MHz Preamplifier
SR240A
-
Stanford Research Systems, Inc.
The model SR240A 350 MHz Preamplifier is a 4-channel, DC-coupled instrument with a gain of 5 per channel. The amplifiers can be used independently or cascaded to provide gains of 5, 25, 125 or 625.
-
Product
AdWords analysis software
AdWords Clever Wizard
-
AdWords™ Clever Wizard is extremely easy-to-use AdWords suggestion and research software. It's always a good idea to check the keyphrases you are going to use in a Google AdWords campaign for their efficiency and popularity. For each keyphrase AdWords™ Clever Wizard shows the number of searches per month, its KEI, overall ad efficiency, average bid (Google source) and also suggests a number of synonyms you can check right away. Supports Unicode. Allows you to import and export keyphrase lists.
-
Product
HandyScope HS6-DIFF With SureConnect: 200 MS/s, 250MHz BW, 4 Channel (256MS/ch), USB Differential Digital Storage Oscilloscope, Spectrum Analyzer, Voltmeter, Transient Recorder
HS6-DIFF-200XMS-W5
-
- 1GS/s sampling and flexible resolution of 8-16 bit.- Four input channels up to 250 MHz analog bandwidth- Highly accurate 1 ppm time base- DC Accuracy of 0.25 % and 0.1 % typical- Very fast 200 MSamples per second USB streaming Data logger- Spectrum analyzer with 32 million bins- Optional SureConnect connection test on all channels- Up to 256 MSamples memory per channel
