Automatic Test Systems
execute test program sets automatically. Also known as: ATS
See Also: Automatic Test Equipment, ATE Integrators
-
Product
Mini LED Backlight Module Automatic Optical Test System
7661-K003
-
Chroma 7661-K003 Mini LED Backlight Module Automatic Optical Test System contains a 71803-2 2D color analyzer to measure chromaticity and brightness
-
Product
Flicker Measuring Probe for LCM ATS
A712306
-
The Chroma A712306 Flicker Measuring Probe for LCM ATS is specifically designed for adjusting the flicker on LCM automatically following the FMA(Flicker Modulation Amplitude) standards defined by VESA (Video Electronics Standards Association) and JEITA (Japan Electronics Information Technology Industries Association) for flicker measurement.
-
Product
PXI Hybrid Single SP6T Switch, DC To 26.5 GHz, Terminated
M9157C
-
M9157C operates from DC to 26.5 GHz, providing a low-cost operation switching solution for measurement and automation of Automatic Test Equipment (ATE) systems without compromise in the RF performance. It is being used in applications such as ATE, RF communication and RF parametric measurements where a rugged switching module is needed for signal routing. Typical switching applications for multiport coaxial switches include signal routing to a single input to multiple instruments and routing of multiple input signals.
-
Product
RF Conducted Immunity Test System
RFCI61000-4-6
-
RFCI61000-4-6 RF Conducted Immunity Test System is an automatic test system which is for the conduction sensitivity testing, it is fully meets IEC61000-4-6.2006, ISO11452-4, GB/T17626.6-2008 and GTB152B-CS114 etc standards. RFCI61000-4-6 internal source and broadband power amplifier can be generated 3 voltage test levels: 1v, 3v and 10v, and has the function of the real detect output level. It has two operation software which is calibration software and test software. When measuring, the signal is in 1 KHZ sine wave amplitude modulation system (80%) to simulate the actual harassment, and can through the coupling/decoupling network (CDN or electromagnetic clamp) to make the harassment signal coupled to the device.
-
Product
System Instruments
-
bsw TestSystems & Consulting AG
Many tasks in the area of semiconductor characterization as well as in the testing of electronic assemblies are routine tasks. Test series of new building elements or samples from production are routinely measured in a large number of electrical parameters. For this, you do not need a measuring device with a complex graphical user interface. A simple interface for remote control with a PC is sufficient. The evaluation and visualization of the results is also carried out on the PC. With the Keysight E5270B and its "little brother" the E5260A two powerful modular SMU units are available for the purpose of the integration into automatic test systems.
-
Product
Regenerative AC Load
61800
-
Chroma Power Electronics Test Solutions not only apply in the industries of Information Technology, Communication, Aerospace and National Defense, but also in energy efficient products such as Hybrid Automobiles, LED luminance devices, solar and fuel cells that are developed aggressively under the pressure of natural resource constraints. Chroma has a wide variety of instrumentation including AC Power Sources, DC Power Supplies, DC Electronic Loads, AC Electronic Loads, Digital Power Meters, and Automatic Test Systems that are ideal for power input/output terminal tests and dynamic simulation.
-
Product
Goniophotometer for Traffic Signal Lamps
LSG-1950S
-
LSG-1950S is a high automatic test system for luminous intensity distribution of luminaires and can be applied to quality evaluation and quality control for signal luminaires, luminaires for cars, motors, vessels and Retro-reflectors. LSG-1950S system is a goniophotometer which can measure all kinds of lamps and luminaires.• Rotations of test samples around both vertical axis (-90°~+90°) and horizontal axis (-35°~+35°) • Accuracy of angle: 0.1° • Resolution of angle: 0.01° • Photometer detector: CIE class A (standard class) accuracy • All software control, high intellectual faculties and simple operation
-
Product
Specialty Instruments
-
Advanced Thermal Solutions, Inc.
ATS offers a variety of unique specialty instruments, designed for specific applications across the electronics industry. These instruments range from providing heat flux measurements and cold plate characterization, to precise isothermal surface temperature control and fan flow characterization.
-
Product
Test System
DA-1 ATS
-
The DA-1 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Test Solutions for Networked Vehicle Components/Connected Cars
Infotainment & Telematics
-
Developing automatic test systems for the automotive industry is one of our core areas. This industry in particular is characterized by rapid technological progress and ever faster time-to-market requirements.In the vehicle, multimedia devices are used for pure entertainment, but also as vehicle information, which are intended to cover security and navigation services.Infotainment and telematics devices such as eCall modules, connected gateways, instrument clusters or the HMI (Human Machine Interface) are networked with each other and with the most important vehicle functions. All of this is made possible - in addition to GNSS (Global Navigation Satellite System) - by wireless and new communication standards such as A 2 B, BLE, C-V2X, Wi-Fi 6 and 5G.The complex networking is a very attractive factor for drivers and passengers, but this complex communication can become a major challenge for developers.High-speed interfaces and high-frequency modules used in combination must send and receive signals between the different devices absolutely error-free.With our individual and sensitive test and inspection systems, we also simulate vehicle components or emulate the vehicle environment and thus ensure the functionality of your devices. We take your pioneering developments to the next level.
-
Product
Industry Standard in Noise Measurement
PN9000
-
The PN9000 is a simple and fast Automatic Phase Noise Test System covering a very wide frequency range(2 MHz to 140 GHz). Its modular architecture allows optimum configuration, multiple measurement techniques and future growth in a compact instrument.
-
Product
Electric Vehicle Supply Equipment ATS (EVSE ATS)
-
It is a customized system based on Chroma 8000 ATS specializing inverification of EV Supply Equipment (EVSE) and complying with SAE-J1772 in programming the test items for operation.
-
Product
ARTES Automatic Relay Test Systems
-
The purpose of power system protection is to use accurate and reliable protection devices to detect faults promptly and without fail and to minimize impairments to the power supply by selectively switching off faulted sections of the system.The use of suitable protection devices can significantly improve the safety and reliability of complex electrical power systems and installations. Regular testing is the only way to ensure that these protection devices function correctly throughout their operational life.More than 20 years of experience in developing and manufacturing automatic relay test systems have gone into creating the third generation of ARTES test instruments. Back in 1996, KoCoS was the first company to present Windowsbased testing software for controlling and operating test equipment and the company continues to play a pioneering role in the design of clearly structured and ergonomic user interfaces today.
-
Product
AC / DC Electronic Loads – Benchtop Testing to Automated Test Systems
-
Chroma Systems Solutions, Inc.
Chroma is the global leader in Electronic Load manufacturing. Chroma’s AC Electronic Loads are designed for testing uninterruptible power supplies(UPS), Off-Grid Inverters, AC sources, and other power devices such as switches, circuit breakers, fuses and connectors. Chroma’s DC Electronic Loads are used for power testing in all markets including automatic test systems, LED, power supply testing, battery testing, and fuel cell testing. Chroma loads can do it all including full current down to 0.4VDC, CZ mode, user defined waveforms, timing measurements, and 3 current ranges per load. Chroma’s electronic loads come standard with either USB or RS232 ports for control and can be configured for GPIB (IEEE-488) control as well.
-
Product
Electrical Equipment Test System
C8900
-
Chroma Systems Solutions, Inc.
The 8900 electrical equipment ATS can complete measurement and test procedures simultaneously and automatically. This automated functionality decreases the risk of errors due to improperly written tests. Chroma 8900 solves the Electrical Safety Test and special FUNCTION test solution.
-
Product
HF test adapter
-
High-frequency test adapters (HF adapters) from INGUN are designed as a replacement set system, consisting of a manual test adapter (MA 21xx and 32xx series) and a high-frequency shielded replacement set from the ATS MAxx/HF series.
-
Product
Magneto-inductive Testing
MAGNATEST D-HZP
-
Foerster Instruments, Incorporated
The MAGNATEST D-HZP by FOERSTER is the ultimate magneto-inductive test instrument: the fully automatic system tests materials for their properties. It operates in single coil absolute mode, making a comparator coil unnecessary. The combination of high excitation currents and complex evaluation electronic equipment detects even very small structural discrepancies. The MAGNATEST D-HZP also provides comprehensive options for documenting test results, such as test piece statistics, histogram, and test data export, which are displayed clearly on the large color display.
-
Product
PXI Hybrid Coaxial Switch: DC To 40 GHz, Single SP6T, Terminated
M9157CH40
-
M9157CH40 operates from DC to 40 GHz, providing a low-cost operation switching solution for measurement and automation of Automatic Test Equipment (ATE) systems without compromise in the RF performance. It is being used in applications such as ATE, RF communication and RF parametric measurements where a rugged switching module is needed for signal routing. Typical switching applications for multiport coaxial switches include signal routing to a single input - to multiple instruments and routing of multiple input signals.
-
Product
Passive Component ATS
-
Test and packing speeds from 80ppm to1,800ppmStandard functions - Inductance/quality factor test - Winding resistance test - Polarity testOptional functions - Layer short test - Insulation resistance test - Bias current testCircular vibrating plate design feeds inductors steadily and rapidlyIndex disc design eliminates dropped inductorsFour-wire measurement test socket designAutomatic discharge mechanism when feeding errors occurEach test station has an independent NG (No Good) product collection boxTest without packaging function provided, good products gathered in bulk collection boxExclusive data collection software designed for monitoring product quality in real timeReserved stations for number spraying and automatic optical inspectionSwitchable Chinese/English/Japanese operating interfaceEquipment is fast, stable and safe
-
Product
Electrical Safety Test Scanner
19200
-
Support Electrical Safety Test Scanning Support High / Low voltage circuit insulation (Switch module)Support 8 slots for plug-in (removable)Max. 9 slaves for multiple scanners (master/slave interface)Standard RS-232 and USB interface Optional GPIB interface CE Mark19200 can be installed in Chroma Electrical Equipment ATS model 8900
-
Product
Automated Tuners / Impedance Tuners / Load Pull Tuners
-
MT97x, MT98x and XT98x series automated tuners (also known as automated impedance tuners and automated load pull tuners) are precision instruments that are optimized for a broad class of in-fixture and on-wafer applications, and may be used in any automated or manual application requiring the ability to match the impedance of a microwave circuit element or to establish specific impedances at a terminal interface. The tuner design is based on the slide screw concept using the inherently broadband slab-line transmission structure. Each unit has two non-contacting probes deliver high VSWR with superb accuracy and reliability over a wide frequency range. These probes can be fully retracted leaving a low-loss, well-matched transmission line, which is a significant benefit in power related applications where two-port tuners capable of handling large amounts of power are required. As integral components of Maury Device Characterization Solutions, these PC-based tuners are controlled using Maury's family of Device Characterization Software tools, including MT930 IVCAD, MT993 ATS and the DLL-based measurement automation environment. Maury Microwave automed impedance tuners are ideal for load pull, harmonic load pull, active load pull, hybrid active load pull, noise figure, noise parameters and all automated tuner applications.
-
Product
Solar Cells and Modules Online Measurement System
PV-LIT
-
The fully automatic PV-LIT testing system offers individual and serial testing options for solar cells and complete solar modules. The modular testing system allows easy integration into existing production lines and can be used in automated serial testing for quality assurance.
-
Product
Flying Probe Tester
FA1817
-
Flying Probe Tester FA1817, an automatic testing system designed to inspect printed wiring on bare boards. The FA1817’s features and capabilities make it ideal for use in inspecting high-density printed wiring boards. With support for a broad range of test types, from low-resistance measurement to high-insulation-resistance measurement, the system reliably detects the latent defects that trouble end-users.
-
Product
Automatic Safety Test System
LS9955/56
-
The LS9955/LS9956 Automatic Safety Test System is according to GB4706.1, IEC/EN60335-1, UL60335, GB7000, IEC60598, GB4943, IEC60950 and GB9706.1. It used for luminaries, home application and motor tools safety test in production line or Lab R&D.
-
Product
Battery (EV) Automatic Test System
-
Landrex Technologies Co., Ltd.
Battery (EV) Automatic Test System
-
Product
Automatic Test Software
EasyTest 2.0
-
EasyTest © 2.0 is a set of common test automation software platform, with the definition of test engineering, test process editor, test program generation, test execution process, test data on a network share as one of the functions. Using EasyTest © 2.0 can easily set up a large network systems and ground test integrated test system, you can build standalone automatic test system, or automatic control equipment R & D engineers, and other data stored for use in research and development.
-
Product
High Voltage Insulation Tester Module
DP-cPCI-5586
-
DP-cPCI-5586 is a High Voltage Insulation Tester Module. This module facilitates single-board voltage source/measurement features with high voltage output and a nanometer. Occupying a single slot in standard cPCI rack, this module can be used for multiple point cable harness test systems with limited rack space. Applications of this board include automatic test equipment, checkout systems, force voltage measure current, and insulation test.
-
Product
4/8 Channel Optimal Multiport Power Meter
UC8728
-
UC INSTRUMENTS UC8728 4/8 CHANNEL OPTICAL MULITIPORT POWER METER are PC control multiport passive components power meter test system and offer superior performance for the test of multichannel DWDM, WSS, ROADM, AWG & PLC components and modules, optical amplifiers, DWDM system and other general purpose of multiport fiber optical test and measurement applications. The system can be integrated with tunable laser source, optical attenuator & PDL controller provides a high performance passive components and modules automatic test system platform.
-
Product
Arbitrary Load-Impedance X-Parameters
S94520B
-
S94520B Arbitrary Load Impedance X-parameters enables an X-parameter model to be collected over a user defined set of load impedances. S94520B still requires an application to control the load impedance such as S94521B or Maury ATS or IV Cad.
-
Product
Microhardness Tester
MT91 Series
-
Newage Testing Instruments, Inc.
The Newage MT91 System is an automatic microhardness testing system that uses the Rockwell method for the hardness result. Hardness is measured based on the depth of penetration rather than using an optical system to determine hardness based on the impression diameter.
