Relay Drivers
Control the energized state of relays.
-
Product
Programmable Relays
-
You get in one unit 12 Inputs and 8 Outputs relays or transistor. Herewith you can do a lot of bigger scale automation whereas the 10 I/O versions are just to short of I/O’s.
-
Product
3-Phase Protection Relay Tester
HME-702
-
HAOMAI Electric Power Automation Co., LTD.
Economical 3-phase Protection Relay Testerwith 3-phase current(3×40A) + 4-phase voltage(4×120V) output.
-
Product
SWB-2817, 16x22, 0.3 A, Reed Matrix Module for SwitchBlock
781420-17
Relay Matrix Module
16x22, 0.3 A, Reed Matrix Module for SwitchBlock - The SWB‑2817 is a reed relay matrix module for SwitchBlock systems. Designed for high power, it can operate as an individual relay card or expand in a single carrier or single PXI chassis. You can connect any input to any output, individually or in combination. You can use matrix switches to route signals from oscilloscopes, DMMs, arbitrary waveform generators, and power supplies to various test points on a unit under test (UUT). The primary benefit of matrix switches is simplified wiring—the overall test system can easily and dynamically change the internal connection path without any external manual intervention.
-
Product
Laser Drivers & Controllers
-
Fast Pulse Generators for E/O ModulationFast Laser Diode DriversSeed Laser Pulse PickingMOPA timing and controlCustom Delay and Waveform Generation
-
Product
Four Channel Clock Driver Card
PI-41401
-
The PI-41401 is a four channel Clock Driver card capable of operating up to 140 MHz at 3V and 100 MHz at 5V amplitudes into a 50 Ohm load. The PI-41401 has a clock rate of 90 MHz at an amplitude of 5 volts into a 1-MOhm load. Into a high impedance load the output voltage range is from –5 volts to +8 volts with the pulse amplitude ranging from 0V to 9V. When driving a 50 load the voltage range is –2.5 volts to 4.0 volts with the pulse amplitude ranging from effectively 0V to 4.5V. Each channel has a common edgespeed control to vary the rising and falling edges of the output waveform. The adjustable slew rate range, for any amplitude, is the minimum edgespeed of that amplitude times 5. The output pulse amplitude and the load being driven determine the range of variability.
-
Product
Low Thermal EMF Relays
Series 100
-
The Pickering Series 100 is a complete range of Single-in- Line (SIL) reed relays primarily intended for direct drive from 4000B CMOS or similar low current sources. They feature a very low level of thermal EMF.
-
Product
Reaction Torque Sensor - Miniature Screw Driver
-
Futek Advanced Sensor Technology, Inc.
A generic term for any (usually computerised) instrument (e.g., Formic’s Fusion software), which may be used to capture data so that audit departments can undertake audit projects including document audits, essence of care audits, infection-control audits, identified risk audits, local priority monitoring, national audits, NICE guideline compliance audits, National Service Framework compliance, Standards for Better Health and Commissioner assurance.
-
Product
Phase Modulated Driver
-
The Phase Modulation Capable RF Driver / Stabilizer is an eight channel, two phase RF driver intended to drive devices such as the Harris H-401. The driver provides both amplitude and phase modulation capabilities in a single unit. The device can be operated in driver mode where the operator has full control over amplitude, frequency, and phase, or in stabilizer mode where the driver automatically adjusts the operating parameters based on optical feedback from an optical pick-off point.
-
Product
Single-phase Relay Test Set
-
Weshine Electric Manufacturing Co., Ltd
Given the diverse functional requirements of the grid’s protection system, testing capabilities require a new level of sophisticated test hardware and software with which to analyse the entire protection system’s (or individual protection component’s) operation in "real life" situations. It is further necessary that these expanding testing capabilities be met with a similar improvement in the simplification of a test instrument’s user interface and software control.
-
Product
Analog LCD Display Drivers
-
Analog Devices analog LCD display drivers provide a diverse range of options for industrial and commercial applications. The larger than standard rail-to-rail output swing offered by select members of this product line help enable applications requiring greater dynamic range than standard video op amps allow. The high slew rates and high capacitive drive capacity found in this portfolio make it ideal for LCD applications, while low supply current options support battery-powered technology.
-
Product
PXI/PXIe Microwave Relay, Single SPDT, 40GHz, 50Ω, SMA-2.9, Remote Mount
40-780B-541-E
Relay
The 40-780B-541-E (PXI) and 42-780B-541-E (PXIe) are single SPDT 40GHz unterminated microwave relay modules with remotely mounted relays. The 40/42-780B range is available with one, two, three or four SPDT panel mounted relays capable of switching frequencies up to 67GHz in 50Ω or 2.5GHz in 75Ω. Connections are made via high quality RF coaxial connectors, SMA or N-Type for 50Ω and 1.6/5.6 in 75Ω versions. Remote versions can support up to three SPDT relays in a single slot.
-
Product
ADC Drivers Fully Differential Amplifiers
-
Differential amplifiers allow the process of single-ended input to complementary differential outputs or differential inputs to differential outputs. These amplifiers feature two separate feedback loops to control the differential and common-mode output voltages. Analog Devices fully differential amplifiers are configured with a VOCM pin, which can be easily adjusted for setting output common-mode voltage. This provides a convenient solution when interfacing with analog-to-digital converters (ADCs). ADI also offers a series of differential receiver products that convert differential input signals to single ended output.
-
Product
48 Channel Relay Output Module
DP-VME-4059
-
DP-VME-4059 is a rugged module with 48 channel relay output, constructed using 2 Form 'C' Double Pole Double Throw (DPDT) relays. The relay channel operation is controlled through the VME bus. Internal read-back is provided to confirm the selected commands. The pole, Normally Closed (NC) and Normally Opened (NO) contacts are terminated at a pair of front panel 96-pin EURO male connectors.
-
Product
PCI Reed Relay Card, 64xSPDT
50-110B-121
Reed Relay
The 50-110B-121 is a 64xSPDT PCI general purpose switching card and is part of our 50-110B/50-115B range of reed relay switching cards which are available in both Changeover (SPDT) and Normally Open (SPST & DPST) configurations. Connections are made via a front panel 200 pin female LFH connector.
-
Product
Relay Protection Test System
RELAYSTAR 1600
-
HAOMAI Electric Power Automation Co., LTD.
Relaystar-1600 the 6 phase universal relay protection test kit6-phase current (6×40A) + 6-phase voltage (6×150V) output.
-
Product
Single-in-Line Reed Relays
Series 116
-
SIL relays - Smallest board area. 1A version requires 0.15 x 0.27 inches .(3.8mm x 6.8mm). 1 or 2 switches with 10 Watts rating. 5 or 12 Volt coils with optional diode
-
Product
Relay Pro 12-24V Relay Tester
60150
-
Tests relays by simply clipping the test leads onto the relay terminal pins using a 12 or 24v DC power source. Tests a wide range of 4 and 5 pin relays. Including shielded, nonshielded, relays with different pin sizes and 4 pin normally closed relays that other testers may incorrectly show fail. Automatically determines the relay configuration so the fully insulated gator clips can be connected in any order. Eliminates guesswork because you don’t need to connect to specific pins, like other testers. 45" power leads with heavyduty gator clips provide a secure connection to the power source.
-
Product
LXI High Voltage Switching - 50xSPST Plugin Module
65-233-900
General Purpose Relay Module
The 65-233-900 plug-in module is part of a scalable high voltage switch platform that provides a high voltage switching solution with capability up to 9 kV.
-
Product
RS-232 Fiber Optic Auto Powered Line Driver
Model 9271
-
The Model 9271 RS-232 Fiber Optic Auto Powered Line Driver features a standard DB9 interface for maximum performance and reliability of data transmission over glass fiber, eliminating the need for serial to nine-pin adapters. In addition, it brings effective data communications to manufacturing environments. I
-
Product
MOSFET Drivers
-
The bridge driver products handle voltages up to 100V, with industry-leading gate rise and fall times and exceptional input-to-output propagation delay performance. Select parts are available in 4mm x 4mm and 3mm x 3mm DFN packages which meet IPC-2221 creepage and clearance specifications for high-voltage systems.
-
Product
Phase Sensors and Phase Sequence Relays
-
Protect aircraft equipment & other devices from damage due to phase loss or reversal with DARE?s phase sensors & monitors. Designed to monitor the phase sequence of three phase power, DARE?s phase sensors will protect electrical equipment that is sensitive to incorrect phase sequence (rotation), phase loss, or phase reversal.
-
Product
IVI Driver Package
IVI Development
-
The most complete IVI driver package from the most trusted name in IVI. Driver development can be tedious and distracting when you are scrambling to meet product deadlines. Researching the latest IVI standards, lack of driver documentation, and changing firmware all work against your product deadline. As a result, quality control over your product or driver or both can suffer. With IVI Development services from Pacific MindWorks you are free to focus on your product.
-
Product
LED Power Driver Tester
WT2080
-
WT2080 LED Power Driver Test Instrument is the comprehensive test instrument for LED drive power which is according to GB/T 24825-2009 and IEC 62384:2006. It can measure the following parameters: Input Characteristics Test (AC&DC), Output Characteristics Test (AC&DC), Output Start Characteristics Test (DC) and Harmonic Testing.
-
Product
Analog Meter Relays
-
Hoyt Electrical Instrument Works Inc.
Hoyt Transistorized Contactless Meter Controllers are complete, self-contained, compact instruments. The CMT Series has a variety of styles and sizes to meet your specific application requirements. These precise instruments continuously indicate any electrical variable. They provide reliable control in a single, self-contained unit, or optionally, a panel-mounted meter with remote amplifier and output relays.
-
Product
Half, Full Bridge & Three-Phase Drivers For Automotive
-
Renesas' AEC-Q100 qualified 100V half-bridge drivers safely drive MOSFETs for bidirectional controllers in 12V to 48V automotive hybrid powertrains. The advanced ISL784x4 MOSFET driver family enables high current DC/DC conversion with adjustable dead time and maximum efficiency. The ISL784x4 drivers are also well suited for 12V to 24V bidirectional DC/DC converters, as well as other high current buck or boost applications.
-
Product
4 Relay Channels, Latching
RY2
-
The RY2 module features 4 individual single-pole, user SPDT Form C (changeover/break-before-make type) relays (channels). Each channel has a common input terminal (C), a normally closed output terminal (N/C), and a normally open (N/O) output terminal. The channel either energizes or de-energizes the relays (close or open) so that the signal provided on (C) may be switched/directed to either the (N/C) or (N/O) terminals.
-
Product
PXIe Microwave Relay, Dual SPDT, 26.5 GHz, 50 Ω, SMA, Internal Termination, Failsafe
42-781A-222
Microwave Relay Module
The 40-781A-222 (PXI) and 42-781A-222 (PXIe) are dual failsafe SPDT 26.5 GHz microwave relay modules with internal terminations. The 40/42-781A range is available with one or two SPDT switches capable of switching frequencies up to 50 GHz in 50 Ω. They are available with either internal or external terminations and connections are via front panel mounted high quality SMA, SMA 2.9 or SMA 2.4 connectors.
-
Product
Automatic Relay Tester
-
The protective devices such as relays, overload coils, circuit breakers must be checked regularly to ensure that, they are always ready to operate correctly. If a fault occurs in the equipment, which they are protecting, routine relay testing will quickly detect the faulty, incorrectly adjusted protection circuits correctly. It is usually necessary to measure its operating time. The micro controller based time interval meter is used for this purpose in all AJIT brand relay testers.
-
Product
Isolation Relays
-
TransData Isolation Relays provide surge protection for energy metering installations by electrically isolating the pulse input/output wiring path to protect electricity meters, network components, energy management systems and recording devices from damage caused by transmitted or induced electrical surges.
-
Product
Earth Leakage Relays
-
Variable Earth Leakage Relays in compact 35mm din rail mounting cases for use on 3 phase electrical systems.
