Showing results: 826 - 840 of 1059 items found.
-
AlazarDSO -
AlazarTech
With Optional Disk Streaming AlazarDSO is a new, powerful oscilloscope emulation software for AlazarTech''s line of waveform digitizers. The very oscilloscope-like human interface will have you capturing signals and getting results in no time! Users who do not have AlazarTech hardware can still experience the software in demonstration mode using the powerful built-in signal simulator.
-
AST Labs
Test cables for tone generators, butt sets, oscilloscopes, digital multi-meters (DMM), and other test equipment that uses specialized connectors like Bed of Nails alligator clips, RJ11, sheathed banana plugs, etc. Our cables are similar and replaces genuine manufacturer cables from Fluke, Harris, Tektronix, HP, JDSU etc.
-
SW00PCIE -
Keysight Technologies
The PCI Express Validation License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation licenses for PCI Express with coverage across the PCI Express technology starting from Gen4. Together with the subscription model, this enables the support and coverage continuity as the PCI Express technology progresses through generations.
-
SW00IECK -
Keysight Technologies
The IEEE 802.3 CK Tx License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation license for IEEE 802.3 CK (100/200/400 Gb/s). Together with the subscription model, this enables the support and coverage continuity as the IEEE 802.3 CK technology specification progresses through revisions.
-
TSM -
PJ Electronics, Inc.
Compact cabinet that contains a multi-position carry/tilt handle and a rear plastic snap-on cover for cable storage and transportation in the shop or in the field. Tektronix TDS1002, 1 Billion Samples/sec, real time, programmable, storage oscilloscope and includes a built-in 3 phase test selector switch that facilitates 3 phase motor testing by mechanically re-positioning the ground terminal.
-
TLS-0050 -
FriedCircuits
The USB Tester will make it a snap to monitor voltage levels and current usage without having to re-wire your breadboard. Just connect to your oscilloscope or DMM test leads, and you're good to go! The USB Tester has both banana clip sized drills and standard 0.1" headers. When you are not testing current you can add a jumper for normal operation. The USB D+/D- pins are also broken out so you can monitor those on an oscilloscope, or for USB sniffing.
-
J2180A -
PICOTEST Corp.
The J2180A low noise preamplifier provides a fixed, AC coupled 20dB gain while converting a 1 MOhm input impedance to a 50 Ohm output impedance. With a 3dB bandwidth of 0.1Hz to 100MHz, the preamplifier improves the sensitivity of oscilloscopes, network analyzers and spectrum analyzers while reducing the effective noise floor and spurious response. The preamplifier can also serve as a low frequency DC blocker for a spectrum analyzer or you can use it to connect a high input impedance oscilloscope probe to 50 Ohm equipment.
-
Multichannel Oscilloscope -
ZETLAB Company
Multichannel Oscilloscope is used for evaluating signal shape and instant value measurement. It is possible to simultaneously display several signals within the same period, each having their own units of measurement. To compare signals, it is possible to display their oscillograms on the same coordinate axes. A simple and user-friendly cursor control and diagram scaling allow for studying process changes in general and in detail.
-
LiFli -
Fauser Elektrotechnik
The LiFli light flicker meter enables fast evaluation of light sources on the flickering part (flicker / flicker). Especially in the case of LED lamps, the flicker portion can be determined only by one measurement, since it is in the range of 0% to 100% for these luminous means.Audio features enable the flicker to be reproduced acoustically. A voltage output for further analysis by means of oscilloscope or voltage analyzer is available.
-
IMV Corporation
A compact Signal Amplifier to make optimal signal processing being connected with the Servo type Accelerometers. It is used for Vibration Acceleration Measurement, Waveform Observation, for various Analysis in combination with the AC Voltage Meter, Oscilloscope, FFT Analyzer respectively. Furthermore, Voltage signals from the Microphones or Sound Level Meters can be output to the instruments like Recorders along with the Vibration Signals.
-
48265 -
Hickok Inc.
Accurate pressure measurements are more critical now than ever. Increase your diagnostic accuracy by viewing live pressure readings in Gauge (analog & digital) and Waveform formats all at once on your PC. It's like using an oscilloscope and gauge to look at dynamic pressures at the same time. Available in two models to fit your specific needs.
-
CA-323 -
Capital Avionics Inc.
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
PL-10N -
PINTEK Electronics
*MODEL：PL-10N*IMPEDANCE：1.111MΩ*ACCURACY：±0.5%*FREQUENCY B.W.：DC~50MHz*WORKING POWER：MAX. 1Watt*INPUT VOLTAGE：MAX.250VDC or 200V rms AC*DIMENSION：48mm(L)xΦ16mm(D)*WEIGHT：25g*APPLICATION: Matching the impedance of the Scope probe with the DMM. with this converter, the user can use the oscilloscope to watch the wave from and measure the precise reading from the DMM.
-
N2752A -
Keysight Technologies
The N2752A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2752A probe’s InfiniiMode provides the following modes of operation.
-
N2750A -
Keysight Technologies
The N2750A InfiniiMode differential probe is a new generation of low-cost differential active probes compatible with Keysight InfiniiVision and Infiniium oscilloscopes’ AutoProbe interface. It comes with new operation modes and convenient measurements of differential, single-ended, and common mode signals with a single probe tip, without reconnecting the probe to change the connection. The N2750A probe’s InfiniiMode provides the following modes of operation.
