Showing results: 811 - 825 of 1108 items found.
-
N2756A -
Keysight Technologies
The N2756A is a low-cost 16-channel MSO cable kit for InfiniiVision Series oscilloscopes. The kit includes 1 flying lead cable, 5 right-angle grounds, 5 ground extenders, and 18 grabbers.
-
CT4121 -
Cal Test Electronics
The CT4121 is a compact FET probe with very high input resistance and low input capacitance. With a 1.2 GHz bandwidth, this probe is ideal for timing analysis or troubleshooting high speed logic circuits, for design verification of disk drives, as well as for wireless and data communication design. The CT4121 can measure up to ±40 V (DC + AC peak). Compatible with oscilloscopes from all major manufacturers, the probe is powered by the included 9 V battery or direct from the oscilloscope using the included USB power lead.
-
N2140A -
Keysight Technologies
The Keysight N2140A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 200 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
N2142A -
Keysight Technologies
The Keysight N2142A is an extremely low-cost passive probe that provides a switchable 10:1 / 1:1 attenuation and up to 75 MHz bandwidth. It features a high input resistance of 10 MΩ (switchable to 1 MΩ) to address a wide range of measurement needs with low probe loading. The probe can be adjusted for both low-frequency compensation and high-frequency compensation. For the best measurements, you should compensate your probe to match its characteristics to the oscilloscope. This probe is compatible with Keysight InfiniiVision Series oscilloscopes with 1 MΩ input.
-
FE170SR -
Rohde & Schwarz GmbH & Co. KG
The R&S®FE170SR is ideal for early sub-terahertz and 6G research activities. Once connected, the frequency range of the R&S®FSW signal and spectrum analyzer and the R&S®RTP oscilloscope are extended to the D band (110 GHz to 175 GHz), allowing engineers to access the range they need to develop the next generation of mobile communications. The easy-to-use, fully-calibrated solution is compatible with our signal generator, analyzer and oscilloscope environments. Plug it in and start designing the next generation of mobile communications today
-
CP-05 -
KILTER ELECTRONIC CO.,LTD
Connected with Oscilloscope and DMMAC/DC current MeasurementAmorphous Alloy CoreTest range:4A,11us,40A,6us,200A,6us100KHz Noise:20mALow battery indicationSmall size Light weightJaw size:23mm(Max)
-
Aaronia AG
The UBBV series are external, extremely low-noise broadband preamplifiers that can be mounted to any SPECTRAN spectrum analyzer. They are ideally suited for spectrum analyzers and oscilloscopes as well as antennas of all manufacturers and are supplied with extensive accessories.
-
Teledyne LeCroy
With the HDA125 High-Speed Digital Analyzer, Teledyne LeCroy has defined a totally new class of instrument – a high-performance logic analyzer module that can be combined with existing high-speed oscilloscopes to provide unparalleled mixed-signal measurement and analysis.
-
CP-07C -
KILTER ELECTRONIC CO.,LTD
●Connect to Oscilloscope.●AC/DC current Measurement.●Bandwidth: DC~5MHz(-3db). ●Rise time:0.7μs●Noise level: 10mA●Jaw size: 5mm max.●Auto zero at power on.●Relative zero correction.
-
PPE6KV-A -
Teledyne LeCroy
High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.
-
HVP120 -
Teledyne LeCroy
High voltage single-ended passive probes are suitable for a wide range of applications where ground-referenced high-voltage measurements must be made safely and accurately. There is also a sense pin to automatically configure the oscilloscope for use with the probe.
-
N2876A -
Keysight Technologies
The N2876A passive probe offers DC to 1.5 GHz and 100:1 attenuation factor to measure fast edges in high speed applications more accurately. This probe needs 50 Ω input on the oscilloscope.
-
TP-RFS400 -
TEAM SOLUTIONS, INC.
Common Rail Diesel injection systems are becoming more and more advanced. The diesel return flow sensor RFS400 can be used together with a lab scope (automotive oscilloscope) to diagnose the most advanced Diesel injection systems.
-
Vektrex Electronic Systems
Isolated Hall Effect current sensors provide accurate high bandwidth current sensing. Vektrex offers models to 320A. For use, the 50-ohm voltage output is connected directly to an oscilloscope or data acquisition system. VCS sensors are magnetically isolated like clamp-on oscilloscope probes. With secure cable attachment, repeatability is ensured.
-
DP3000 Series -
Texas Co.
A “differential” probe is an active probe which has two inputs, one positive and one negative as well as a separate ground lead and it drives a single terminated 50Ω cable to transmit its output to one oscilloscope channel