Showing results: 241 - 255 of 379 items found.
-
SW00PCIE -
Keysight Technologies
The PCI Express Validation License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation licenses for PCI Express with coverage across the PCI Express technology starting from Gen4. Together with the subscription model, this enables the support and coverage continuity as the PCI Express technology progresses through generations.
-
SW00IECK -
Keysight Technologies
The IEEE 802.3 CK Tx License Suite is part of the subscription based Oscilloscope Compliance Test Software Suites. This suite covers Tx Validation license for IEEE 802.3 CK (100/200/400 Gb/s). Together with the subscription model, this enables the support and coverage continuity as the IEEE 802.3 CK technology specification progresses through revisions.
-
Spinnaker Contract Manufacturing, Inc.
As standard practice, all of our SMT assemblies are washed and tested through our Automated Optical Inspection and pass through our stringent internal QA/QC policies. In Cables and Wire Harnesses, pretests, such as pull tests and crimp type tests, are performed on all builds before being tested for continuity, hi-pot, shorts and mis-wires, to name a few. Our electromechanical assemblies are capable of receiving full functional testing through custom test fixtures and RF test. Some RF tests include Gain/Loss, Frequency Response, VSWR (Voltage Standing Wave Ratio), Inter-Modulation Distortion and Output Power.
-
LXinstruments GmbH
Manufacturers of electrical or electronic products are required by law to carry out an electrical safety test before placing them on the market. This final test takes place at the end of the manufacturing process and is therefore also referred to as an EOL test (end-of-line). Depending on the prescribed standard and directive, the following parameters are tested:- Leakage current and discharge current- Insulation resistance or the insulation strenth- Dielectric strength or electric strength- Correct installation of the protective conductor (ground continuity and ground bond test)- Faultless functioning of the product under the conditions defined for intended use (function or run test
-
DUSPOL -
BENNING Elektrotechnik und Elektronik GmbH
phase-sequence test (counter-clockwise / clockwise)single-pole phase test: " symbol (red LED)measuring point illuminationacoustic and optical continuity testfrequency measurement 1 1000 Hzvoltage indication 1 1000 V AC TRUE RMS / 1200 V DCresistance measurement and diode test with conducting-state voltage indicationlc display with background lightingsensor of non-contact cable break detectorload connection via large-scale push buttonsvibrating alert in the test handleshock-resistant housing with protection against dust and water jets (protection class IP 65) and rubberized test handleDIN EN 61243-3 (VDE 0682-401): 2015 standard
-
Extech CB10-KIT -
Extech Instruments Corporation
The CB10-KIT is an Electrical Troubleshooting Kit that features three tools with 5 functions. The CB10 is an AC Circuit Breaker Finder/Receptacle Tester that locates circuit breakers and tests receptacle wiring. The CB10 allows the user to quickly locate 110 Volt to 125-Volt AC circuit breakers and fuses with audible and visual (LED lights) circuit breaker indication. The product also features a variable sensitivity adjustment to pinpoint correct circuit breaker. The second tool is the CT20, a Continuity Tester/Wire Tracer that tests continuity via bright flashing LED and loud pulsating beeper. The remote probe with LED allows a single user to trace up to three cables. The third tool in this kit is the DV20; an AC Voltage Detector/Flashlight with non-contact detection of AC voltage from 100 VAC to 600 VAC via built-in bright LED flashlight with ON/OFF button built in a rugged double molded housing.
-
LX-1024A+ -
Shenzhen Lian Xin Technology Co., Ltd.
The system provides Chinese/English free switch operation interface,．·Up to 1500Vdc/1000Vac Test Voltage ,．·1024 Max. Test Points ,(Max of all series)．·500 Max Files Memory,support USB or PC unlimited expansion,．·Using Embedded Linux operating system，．·Adopted high resolution colour 640*480 TFT LCD ,．·Large 320×240 LCD display ,．·Instant test time :0-60s , optional adjustment.．·Providing Single-End ,Multi-segment ,Standard ,and Spot test of wire.．·Auto Scan and Auto Pin Search ,．·The system provides advanced instant open-circuit, short-circuit, continuity test,．·Intermittent Conductance Test,．·Intermittent Open/Short Test ,
-
Educated Design & Development, Inc.
1 Button Testing - No setup required, just plug right in!Digital LED display reads out in OhmsAlso performs the Low Current Ground Continuity test, at the same time!Auto Test Time (1 sec. / 60 sec.)+ - No need to set a timer or clock watchCustom universal receptacle accepts both 120V and 240V plugs.Zero feature allows you to "zero-out" the test lead impedance.Meets UL, CSA, CE, EN, IEC, MIL and all other international safety agency requirements.
-
PK-3456 Spy Splitpair -
Pansco, Ltd
Easily & accurately tests twisted pair cables for proper continuity and correct signal pair. A split pair can cause a crosstalk problem and suppress the communication speed. The SpySplitpair also includes a Full test, One-ended testing, Debug mode for checking the specific pair fault, and a Tone mode for tracing cable as well as a Voltage warning indicator to protect the tester. Hub blink/Net Tone mode (PK-3456E only), display of the Ethernet port to which the test cable is connected, and identify unknown RJ45 outlet for active Ethernet.
-
PeakTech Prüf- und Messtechnik GmbH
Compact 3½-digit multimeter, developed according to the CAT III 600 V standard with integrated LAN network tester. In addition to the extensive measurement functions for voltage, current and resistance, this model has a fast-reacting continuity test with an acoustic signal and the possibility of performing diode tests. This combination measuring device is a very practical test device that easily shows the correct pin assignment of network cables by comparing a transmitter with the corresponding cable receiver using an LED. Trouble-free checking of cable passage, open, short and cross connect is possible.
-
2151 IN -
Standard Electric Works Co., Ltd
● Microprocessor-controlled.● 68 × 34mm(2.677” × 1.338”) large LCD display.● 3½ digital LCD(2000 counts) a LCD indicated instrument for insulation.(MΩ), continuity(Ω) and AC voltage.● Three insulation test voltages(DC) : 250V, 500V, 1000V.● Automatic circuit discharge.● Test insulation at rated voltage into a 1mA DC load.● >200mA short circuit testing current for a resistance tests.● Auto ranging.● REL function.● Auto power OFF.● Fuse protection.● Auto data hold.● BS 16 edition.
-
260-8 & 260-8P -
Simpson Electric Company
Nothing beats a Simpson 260-8 for monitoring fluctuating trends and rates. Portable yet with benchtop accuracy, the 260-8 is ideal for use anywhere -- workshop, lab or in the field. The 260-8P features an additional resettable overload protection circuit and audible continuity checking. Both versions come with batteries, manual and full-size test leads with threaded probe tips and screw-on alligator clips.
-
DCM401 -
Draper Tools Ltd
Expert Quality, auto and manual ranging clamp meter capable of voltage, current, resistance, diode, continuity, capacitance, frequency, duty cycle and temperature testing. Maximum jaw - opening diameter of 36mm, backlit LCD screen, auto power off and a useful inspection light. Supplied with test leads, temp probe, case and 3 x AAA batteries.
-
Extech Instruments Corporation
An electronic tool for electricians, alarm, cable installers and others who routinely need to check circuits for continuity and also identify cables and wires. It allows a single user to quickly identify and label two wires even when the wire ends are located in different rooms. It can accommodate test wire lengths up to 10,000-feet (3,000 meters), 26-gauge minimum.
-
6280 TB -
Standard Electric Works Co., Ltd
● Wide range of operating voltage from AC 210V/50Hz to 250V/50Hz.● For checking AC voltage.● For checking a RCD tester's test current & time in mA(ms).● For checking a loop tester.● For wiring check (Phase, Neutral, Earth).● For checking continuity.● For checking insulation (The maximum is 1.2kV).● For checking UK16th edition.● Safety standard: EN 61010-1 / EN 61326-1
