Wire Cable Test
The verification of wire cable integrity.
-
product
Test Fixture, Axial And Radial
16047A
The 16047A is designed for impedance evaluation of axial/radial lead type devices of up to 13MHz. The 16047A employs Kelvin contacts which realize a wide impedance measurement range. The contact tip can be changed according to the device shape.
-
product
Cable Assembly, 200-Pin LFH, Male Bottom Exit (Male Screwlocks) to Female (Female Screwlocks), 2m
A200LMB-200LFR-5B200
This male bottom exit to female rear exit 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by screwlocks.
-
product
Cable Assembly, 37-Pin D-Type, Male to Unterminated With Cut Ends, 1m, HV
A037DM5-C-HA100
The 37-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 37-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
product
Cable Assembly, 9-Pin D-Type Female to Unterminated With Ferrules, 1m
40-972-009-1m-FU
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Environmental Control System Test Platform
The Airframe Environmental Control System Test Platform provides a hardware-in-the-loop (HIL) closed-loop test environment for dynamic and maintenance testing of cockpit and cabin environmental control systems for airframes. The system simulates a military or commercial airframe cabin, including sensors and actuators from the control system and the passengers. The system delivers repeatable, cost-effective testing in a fraction of the time needed with typical in-house simulation systems.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to 4x50-Pin IDC, Female, 2m
40-971B-200-2m-MF
This male rear exit to ribbon cable 2m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-pin LFH connector. It is constructed from 4 bundles of 50-wire round/flat ribbon cables, terminated with 50-pin female 2.54mm pitch IDC connectors. The 200-pin connector can be secured to the product by male screwlocks. This assembly can be used for applications requiring unterminated cables, simply crop off the ribbon cable headers. It can also be used with Pickering 50-Pin Ribbon cable connector blocks.
-
product
SH37F-37M-2 37-Pin Female to Male Shielded I/O Cable, 2 m
778621-02
SH37F-37M-2 37-Pin Female to Male Shielded I/O Cable, 2 m
-
product
Cable Assembly, CAT-5E Ethernet, Thin Profile, 10M
151733-10
8-Pin Male Ethernet to 8-Pin Male Ethernet, CAT-5E Ethernet Cable - The 8M-8M Ethernet Cable connects devices to network hubs or switches. The cable has straight-through wiring and is available in different lengths and thin profile options.
-
product
Cable Assembly, Receiver, Micro Coax, 36", 9 SMA Plugs
540131010247
Cable Assembly, Receiver, Micro Coax, 36", 9 SMA Plugs.
-
product
Cable Assembly, Receiver, 36", TriPaddle, 50 Pin FML DSub
540111030203
Cable Assembly, Receiver, 36", TriPaddle, 50 Pin FML DSub.
-
product
SHC68-68-EPM, 68-Pin Male VHDCI to 68-Pin Female D-SUB, 80 Twisted Pairs, Shielded Multifunction Cable, 1m
192061-01
The SH68M-68F-EPM Cable, sometimes referred to as SHC68-68-EPM, connects DAQ devices to accessories or cables with D-SUB connectors. You can use this cable to create custom cabling for your DAQ device. The SH68M-68F-EPM Cable is offered in different lengths. 80 twisted pairs, 1 connection used in shield. 81 total connections used.
-
product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Tinned Ends, 2m
A009DF4-T-0A200
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire.The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match theconnector pin designation.
-
product
Cable Assembly, 9-Pin D-Type Male to Unterminated With Cut Ends, 2m
A009DM5-C-0A200
A range of 9-Pin D-Type cable assemblies with unterminated connections at one end and constructed from PFA insulated wire. The connector assembly can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation.
-
product
Cable Assembly, 26-Pin D-Type, Male to Unterminated With Ferrules, 1m
40-972-026-1m-MU
The 26-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 7/0.15 (26AWG) Silver Plated Copper Wire. The connector can be secured to an associated product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product
-
product
Benchtop Automated Functional Test
midUTS
Combining bench-top portability with powerful automated test functionality, the midUTS is an extremely versatile yet cost-effective solution for your electronics functional test needs. Comprised of high-performance commercial-off-the-shelf (COTS) instruments, along with Bloomy’s medium-density signal-routing PCBAs, a built-in or USB-connected PC, and a pair of high-integrity, production-grade cables connected to an adjacent benchtop fixture, the midUTS can be used in engineering for PCBA bring up, as well as scaled to manufacturing to perform high-volume PCBA and sub-assembly functional testing. It is also ideal for depot diagnostic test, debug, and repair of field returns. The two mass-interconnected cables connect the midUTS to as many as 320 test points on the unit under test (UUT), supporting an extreme wide variety of products using bed-of-nails as well as cable-connected UUT test fixtures. Most importantly, the midUTS helps you automate sequences of functional tests using NI TestStand and the Bloomy EFT Module for TestStand. This ideal balance between powerful features and affordable cost allow you to automate earlier in the product development lifecycle, substantially increasing product quality and minimizing time-to-market!
-
product
Test System for High Volume Production Testing of Integrated Circuits
ETS-364
The ETS-364 is a general-purpose precision analog and mixed-signal test platform designed for high volume production testing of integrated circuits; optimized for high throughput applications with a fully integrated multisite software and hardware architecture.
-
product
Cable Assembly, Receiver, Mini Power, 36", 8-Pin Female Power D-Sub
540154010208
Cable Assembly, Receiver, Mini Power, 36", 8-Pin Female Power D-Sub
-
product
Cable Assembly 68-Pin Micro-D Female to Unterminated, Cut Ends, 2m
A068SFR-C-6A200
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by 2-56 UNC Screwlocks.
-
product
Cable Assembly, 200-Pin LFH, Male Bottom Exit (Male Screwlocks) to 4x50-Pin D-type, Female, 1m
A200LMB-04F050D5B100
This 200-pin male to 50-pin female D-type 1m long cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin LFH connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by screwlocks. This cable assembly can be used with Pickering 50-Pin D-Type connector blocks (refer to 90-005D).
-
product
Cable Assembly 44-Pin D-Type Male to Female, 1m
40-970-044-1m-MF
The 44-Pin D-Type Density and a Half cable assembly is constructed from 7/0.15 (26AWG) Silver Plated Copper Wire with PFA insulation. Screwlocks are provided to secure the connectors to their associated products.
-
product
Cable Assembly, Receiver, TriPaddle 256, 20", 3 68-Pin Male VHDCI
540307020105
Cable Assembly, Receiver, TriPaddle 256, 20", 3 68-Pin Male VHDCI
-
product
Cable Assembly, Receiver, QuadraPaddle, 20", 160 Pin Male LFH
540262010140
Cable Assembly, Receiver, QuadraPaddle, 20", 160 Pin Male LFH
-
product
Cable Assembly, 160-Pin DIN41612, Female To Female, 1m
40-970A-160-1m-FF
The cable assembly is suited for direct connection to Pickering Interfaces products using a Female DIN41612 connector. For applications in LXI products where 4 connectors are used in a horizontal row if the user requires all connectors to have a second fixing then the right hand connector can be fitted with the optional screwlock assembly 40-969-101.
-
product
Test Platforms
Leverage 20+ Years of Test Industry Experience with Built-In IP for Maximum Reuse
-
product
500-Pin SEARAY Cable Assembly, Male to 5x50-Pin D-Type, 2 Amp, 2m, 250 Port
A500RMR-05F050D5C200
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. The male SEARAY connector of this cable assembly is suitable for direct connection to Pickering Interfaces products. Five 50-Pin D-Type connectors allow an interface to other devices. Screwlocks are provided at both ends to secure the cable assembly to mating products.
-
product
Wafer-Level Parametric Test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
product
Cable Assembly, 200-Pin LFH, Male (Male Screwlocks) to Female (Male Screwlocks), 1m
This male to female 1m cable assembly is suited for direct connection to all Pickering Interfaces products using the 200-Pin connector and is constructed from 4 bundles of 50-wire round/flat ribbon cable. The connector assembly can be secured to the product by male screwlocks.
-
product
SH68M-68M-EPM, 68-Pin Male VHDCI to 68-Pin Male VHDCI, Twisted Pair, Shielded Multifunction Cable
190233-0R5
68-Pin Male VHDCI to 68-Pin Male VHDCI, Twisted Pair, Shielded Multifunction Cable - The SH68M-68M-EPM Cable, sometimes referred to as SHC68-C68-EPM, connects DAQ devices. The cable includes separate digital and analog sections, individually shielded twisted pairs for analog
-
product
Cable Assembly 15-Pin D-Type, Male to Female, 0.5m
40-970-015-0.5m-MF
The 15-Pin D-Type cable assembly is constructed from 19/0.18 (21AWG) Tinned Copper Wire with PFA insulation. Male screwlocks are provided to secure the connectors to their associated products. The 15-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
product
500-Pin SEARAY Cable Assembly, Male to Unterminated, Ferrules, 1 Amp, 1m, 500 Port
A500RMR-F-1B100
The 500-Pin SEARAY connector is used on switching products to provide a very high density 1A connector solution that is suitable for use to 200VDC.
