Burn-In Boards
Printed circuit boards (PCB) filled with integrated circuit (IC) sockets for purposes of connecting an array of IC packages for burn-in test.
See Also: Burn-In, High Power Burn-in, Burn-In Sockets
-
Product
Tape Up and Down Conversion Board
LS-37-P
-
The IF Digital processing board is a workhorse for all digital demodulation and combing. It can also support other unique functions like sub-carrier demodulation, FM/FM demodulation and tone receiving. Please consult the factory for your unique requirements.
-
-
Product
12-bit, 100KHz, 4SE/2DIFF Isolated Analog Input Board
APCI-3001-4
-
4 single-ended or 2 differential inputs 12-bit resolution Optical isolation 500 V 100 kHz data transfer rate Automatic analog acquisition 8 digital I/O, 24 V, isolated, timer Trigger functions Graphical display of the measured data
-
Product
3U cPCI Synchro/Resolver Simulation Board
75DS2
Simulator
NAI’s 75DS2 is a Synchro/Resolver Simulation Board with four independent, isolated channels. These channels can incorporate up to four Digital-to-Synchro/Resolver Simulation Converters with 1.5, 2.2, or 3 VA drive capability, or either two or four Digital-to-LVDT/RVDT Simulation Converters. One of the outputs on each channel can be grounded without affecting performance.
-
Product
Automotive Production Board Test
-
Teradyne's TestStation platform enables manufacturers to easily react to rapidly changing product requirements. From volume, mix and test complexity - there is a TestStation configuration to meet your production requirements at the highest fault coverage and yield rate. configurable from a range of a few test points for basic shorts detection up to more than 15,000 test points for more complex PCBAs.
-
Product
BMP-4 Board Marker Probe
BMP-4
ICT/FCT Probe
Current Rating (Amps): .020Voltage Rating (VDC): 12Recommended Duty Cycle: 2 sec. On (min.), 3 sec. OffTest Center (mil): 1,000Test Center (mm): 25.40Full Travel (mil): 79Full Travel (mm): 2.01Recommended Travel (mil): 50Recommended Travel (mm): 1.27Full Marker Travel (mil): 62Full Marker Travel (mm): 1.57Direction of Rotation: CCWScribed Diameter (mil): 50Scribed Diameter (mm): 1.27Test Center Remark: Ø .398 (10.1) or M10
-
Product
3U CPCI I/O & Comm Board W/Gig-E Switch
75D4-H2
Multifunction I/O
The 75D4-H2 is a Layer 2+ Gigabit Ethernet Switch built upon NAI’s multifunction, 3U cPCI board technology. The 75D4 motherboard contains a high-density I/O module slot that supports an H2 switch function. The 75D4 with H2 consumes approximately 9.5 W of total power at 5 V to operate at full 1000 Base-T speeds. In addition, the 75D4 motherboard can integrate four channels of RS232/423/422/485 serial communications. This adds an additional 1.5 W of 5 V power. Serial data is available on the cPCI bus or can optionally be available over Ethernet via the use of one of the switch ports.
-
Product
Burn-In Test Sockets
-
The selection of the test socket is critical to the performance of a device during qualification testing where electrical bias and signals are applied. Key factors such as mechanical compatibility, operating temperature, ability to withstand high moisture levels, signal speed and lead inductance/capacitance all need to be taken into account when selecting the best socket for the test application.
-
Product
3U VPX UltraScale Kintex FPGA Carrier Board With FMC+ Site
VPU: 085/115
-
The VPU utilizes the AMD Kintex UltraScale XCKU085 or XCKU115 FPGA as options. The Kintex UltraScale FPGA family delivers impressive processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks.
-
Product
Squid Carrier Board™ Family PCI Express Gen 2 Carrier Board for 4 PCIe M.2 SSD Modules
SKU-086-01
-
The Squid PCI Express Carrier board for M.2 SSD modules is the second product in the Squid PCI Express Carrier Board™ family. PCI Express Carrier board was designed to expand modern motherboards that have PCI Express interface. It allows connection of up to 4 M.2 PCI Express SSD modules. This product is recommended for use in Mac Pro Desktop computers.
-
Product
VXI Register Interface Board
VXI-5524A
-
*VXI Register Interface mates with user's PCB to form a B or C-size module.* 48 Digital IO Lines - Three 16-bit registers set as latched outputs or gated inputs.* 16 line bi-directional expansion bus for driving external logic.* Digital IO and VXIbus lines are 3.3V logic levels and are 5 V tolerant for compatibility with 3.3V logic and 5V VXIbus signals.* User selectable 3.3 and 5 Vdc puliup voltage on the digital IO lines for sensing switches etc.* The VXI-5524A board is a complete VXI-1 Rev 1.4 and VXI-2 compliant register-based interface.* User configurable model number, manufacturer ID, version and serial numbers.* Two companion component boards available for prototyping IC or RF assemblies.* Companion hardware kits available for building 1, 2 or 3-slot wide modules.
-
Product
3U And 6U CPCI CARRIER Board
MS 1715
-
*Bus Interface:- 32 Bit/64 bit PCI Bus with cPCI Interface*Two slots of 32/64 bit PMC connector interface*Speed of operation up to 66MHz*64 bit, 66MHz PCI Bridge based design*Self Test future
-
Product
10 Gb/s SFP/SFP+ Evaluation Board
EV-SFP-171
-
The purpose of this SFP+ evaluation board is to provide the designer with a convenient means for evaluating SFP+ fiber optic transceiver such as 10 Gb/s(up to 16 Gb/s) SFP/SFP+ transceiver compliant with ANSI Fibre Channel FC‐PI‐5 for high speed electrical and optical specifications. This board provides SMA connectors for high speed TX and RX signals. The low speed control signals such as Tx_Fault, Rx_LOS and Rate_Selects can be controlled by using on board switches and test points. A connector for 2 wire serial interface to the module is also provided.
-
Product
I/O Extension Stack Board For DP, USB, And Audio Extension
PCE-SA01
-
I/O extension stack board1 DP, 2 USB 3.0, MIC-in, LINE-outDimensions (L x H) : 68 x 125 mm (2.67" x 4.92")Supports Model: PCE-3029, PCE-4128, PCE-4129Support Model: PCE-5029/5031/5032/ 5033/5129/5131/5132/5133/7129/ 7131/7132/7133; PCE-3029/3032/ 4129/4132
-
Product
PCI Express UltraScale+ FPGA Carrier Board With FMC+ Site, X16 PCIe Gen 4
PG4+
-
The PG4+ continues DEG’s commitment to delivering high performance processing solutions for mission critical applications requiring the latest in AMD UltraScale+ FPGA computing power. The PG4+ is a PCI Express, standard form factor, FPGA processor board designed to meet the needs of challenging, embedded high-performance digital signal processing applications. The AMD UltraScale+ VU37P or VU47P delivers superior processing capabilities and supports operations such as: FFTs, FIR filters, fixed-point and repetitive processing tasks. The PG4+ FPGA node processes input from the FMC HPC + (Vita 57.4) site, allowing for maximum application configurability and performance when coupled with DEG’s market leading ADC and DAC FMC modules that operate up to 12 GSPS.
-
Product
Intel x51 Based Boards
MS 1507
-
- General Purpose I/O Signals- RS232/422 Interface- External Bus, External Interrupts
-
Product
Timing Board #2
TIO-10 #2
-
Interface board for converting signals on a National Instruments PC-TIO-10 timing board to and from fiber optic signals. This board is similar to the Fiber Optic Interface to National Instruments TIO-10 Timing Board #1 only it has more channels connected to fiber optic transmitters and receivers.
-
Product
Sensor Board for micro:bit
-
The MonkMakes Sensor Board for micro:bit allows you to sense sound level, temperature and light level. You can connect it up to your micro:bit using alligator clips.
-
Product
Nano-ITX Embedded Board
-
The Nano-ITX form factor is designed as a high integrated native x86 embedded platform, measuring a mere 120 mm x 120 mm which measures in at 50% smaller than the Mini-ITX form factor. The Nano-ITX form factor is available with a rich feature set and is targeted at the fast-emerging embedded markets, allowing developers to highly customize their system designs in the low-profile and fully-configured embedded devices.
-
Product
Digital Output
VME-2170A
Digital Output Board
The VME-2170A optically coupled digital output board consists of VMEbus compatibility logic,data control logic, four 8-bit output registers, and 32 optically isolated high-level outputs. The board is implemented as a double Eurocard form factor PC board, and provides all necessary address decoding and data transfer control logic to accept both 8- and 16-bit data transfers. Optical couplers isolate the 32 outputs from each other and from the VMEbus.
-
Product
COM Express Type 6 Application Board With LVDS, VGA, DDI, Dual LANs And Audio
CEB94021
-
*125 x 95 mini size form factor*2 GbE LANs*SATA-600*LVDS, VGA and DDI*4 USB 2.0 and 2 USB 3.0*2 PCI Express Mini Card slots*3 RS- 232/422/485 and 1 RS-232
-
Product
Electronical Load Board 3U VME64x (air cooled)
056-921
-
The 3U load boards are designed to simulate the power consumption of a single board computer and other boards on the backplane.
-
Product
TI HDC1080 Humidity and Temperature Sensor Breakout Board
SEN-37001
-
Breakout board for the Texas Instruments HDC1080. This sensor is an extremely accurate temperature and humidity sensing device, with +/-0.2C temperature and +/-2% humidity accuracy typical. These specs far exceed the accuracy of ICs that came before it, including the HTU2x and SHT2x series, and improves upon the success of the HDC1050. In addition, the HDC1080 has a wide input voltage range of 3V-5V and includes temperature and airflow cutouts as recommended for the best operation. Finally, in the case of environmental changes that could cause light condensation, the HDC1080 has a built-in heater to burn off any condensate. Example code (Arduino platform) is available below.
-
Product
Data Acquisition Processor Board
DAP 5000a
-
When your application needs Pentium-powered real-time processing under Windows, choose the DAP 5000a. Even at maximum sampling rates, the combination of a fast processor with low latency allows computation in real time between samples – and on-time response for control applications.
-
Product
4K Custom Lens USB 3.0 Camera Board (Color)
See3CAM_CU135
-
See3CAM_CU135 is a 13MP fixed focus 4K USB camera board with good low light performance and iHDR support. This 4K board camera is based on 1/3.2" AR1335 CMOS image sensor with advanced 1.1µm pixel BSI technology from ON Semiconductor® It has S-mount (M12) lens holder which allows customers to choose and use the lens according to their requirement. It is a Plug-and-Play camera (UVC compliant) for Windows and Linux. This 4K board camera is also backward compatible with USB 2.0 host ports.
-
Product
Interface Board, Compact, 8:1 Ethernet RJ45
40-965-907
Interface
Compact converter card for 40-736 Data Communications Multiplexer. Adapts the 78-Pin D-type connector on the front of the module to 9 RJ45 sockets. Allows the multiplexing of up to 8 Ethernet signals with speeds up to 1G bit.
-
Product
3U PXI Express Board Virtex-5 Medium Speed Quad DAC
SMT759
-
Sundance Multiprocessor Technology Ltd.
The SMT700 module uses a Xilinx Virtex 5 LXT or SXT to implement the interfaces the board provides. The FPGA can be configured either via the onboard flash, or through the Xilinx JTAG header.
-
Product
Board
STEMlab 125-14
-
It has two 125Msps 14-bit inputs and two 14-bit outputs, Xilinx Zynq 7010 FPGA and offers remote access, with an online app user interface accessible through Ethernet or Wi-Fi.
-
Product
RTM Discrete Signal Conditioning Board
MS 3632I
-
CPCI Rear IO Discrete Signal Conditioning Board is a signal conditioning and interface board for CPCI based Advance Compute & IO Module (MS3639i). This board primarily focusing on signal conditioning of TTL/CMOS DIO levels to required type of discrete input and output interface. Digital IO from ACIO board to discrete IO at Rear IO interface. Board takes 144 DIO from ACIO and does Open/Ground, 28V/Open, 28V/Ground configuration. In addition it shall generate additional 32 discrete input / output signals with signal conditioning and all IO interfaces are brought to two 96 Pin Euro Connector.
-
Product
3U VPX Graphics Output Board
GR2
-
The Abaco GR2 is a 3U VPX graphics output card based on NVIDIA® Pascal™ Quadro® P5000/P3000 GPUs. The GR2 offers very high performance graphics and GPGPU capability – up to 6.4 TFLOPS floating-point - with CUDA™ and OpenCL™ support.
