ATE Fixtures
Holding and positioning assemblies to guide UUT I/O access by automated test equipment.
See Also: Test Fixtures, PCB Test Fixtures, Board Test Fixtures
-
Product
Grips and Fixtures for Test Stands
-
AMETEK Sensors, Test & Calibration
Our comprehensive range of grips, fixtures, jigs and probes cover most test applications within a wide range of industries. Below you will find a selection of our most popular grips, fixtures, jigs and probes. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Product
Ethernet Test Fixtures & Software
-
We have developed a series of custom testing tools as part of our dedication to performing the most comprehensive Ethernet testing in the industry. These tools allow for testing at lower layers than most commercially available tools and are available for use in your own testing labs. In addition, we have an extensive amount of T&M partner test tools which members of our Ethernet testing services also have access to.
-
Product
Actuation Methods for In-Circuit Test Fixtures
-
Commonly referred to as In-Circuit Test (ICT), loaded board test can be defined as the task of measuring values of components that have been installed on a printed circuit board (PCB). A second basic category of loaded board test measures simple open and shorts on the board to verify manufacturability standards. Circuit Check supports all forms of in-circuit test strategies with its Performance Grade and Value Line test fixtures.
-
Product
High Temperature Component Test Fixture
16194A
Test Fixture
Measure both axial/radial leaded devices and SMD within the temperature range from -55 to +200°C.
-
Product
Topside Probing In-Circuit Test Fixtures
-
Circuit Check matches top side test targets to your specification and needs. The Signature Series pneumatic drive fixture is the industry standard for precision, accuracy and repeatability.Today’s fifth generation Pneumatic drive supports as many as 8,000 test probes with centerline spacing to 25mil, and contacting test pads as small as 0.014″.
-
Product
USB-C® Tx & Long Chnnel Rx Precet. Test Fixture
AUT20044 Rev:B0
-
The original Intel USB-C 3.1 Tx Test Fixtures includes two types of fixtures, UFP and DPF. Allion Pre-Cert Test Fixture integrates functions of the two fixtures into an one-board solution, eliminating the hassel to frequent switching of two fixtures.
-
Product
Exchangeable Test Fixture
MA 2111/D/H/S-5/HG
-
Parallel contact stroke: 15 mmContact force max.: 2000 NInterface block required: Test system sideInterface signals max.: 850Component on PCB: 58 mmPressure frame unit-opening angle: 75Installation height test probe top: 16,0 mmInstallation height test probe bottom: 10,5 mmInstallation height dual-stage test probe bottom: 16,0 mmweight: 10,70 kg
-
Product
Vacuum Test Fixtures
-
Vacuum fixture kits for Pylon block fixture, Teradyne, Keysight, Digitaltest,Seica, Cobham (Aeroflex), ATX exchangeable system.
-
Product
Dual Servo Electrical Test Fixture
TA-334001
-
The TA-334001 is a Dual Servo Electrical Test Fixture made to be an equivalent substitute for the Honeywell test fixture T-334001. The test fixture front panel duplicates all the proper switch numbers and descriptions so the technician can follow by the book testing. The panel overlay text is reverse screened (backside) to insure that text quality will not degrade over time. All the appropriate test jacks are provided on the panel for servo pin and bracket breakouts. This fixture provides for the switching of motor direction, clutch, tach selection, synchro selection, limit switching and polarity relays. Panel meters are provided on the test fixture so that the technician can monitor the servomotor voltage as well as clutch voltage and current.
-
Product
Functional Test Fixtures
-
EMC Technologies designs and manufactures discretely wired and wireless functional test fixtures used for performance verification of PCBs and Electronic Assemblies. Commercial applications have included work in support of many industries including: satellite TV, computer servers, medical, networking, and telecommunication.
-
Product
Clamshell Type Mechanical Fixtures
Series 30
-
Semco’s GR Series 30 mechanical kits are an inexpensive solution to printed circuit board testing that requires the benefits of GR2270 style (VG) interface compatibility.
-
Product
Universal Breakout Test Fixture
CA-323
-
The CA-323 Universal Breakout test fixture was designed to provide, as the name suggests, a universal test solution for aircraft trouble-shooting. The unit gives the technician the ability to monitor (100) different conductors or open an individual conductor for simulation or measurement. Any avionics component can be extended and in many cases with only a voltmeter and oscilloscope the operation in question of the Unit Under Test can be determined.
-
Product
Turn-Key Functional / Mechanical Fixture
-
In addition to In-circuit testing, functional testing is widely used in the industry to verify electronic cards. This is why ReMaTek has always paid a special attention to the specific requirements of functional testing. Our dedicated engineering staff is prepared to handle all of your mechanical, electrical and software requirements. We are aiming particularly the small turn-key test systems where all the elements; the mechanical fixture, the test equipment and the test software, are put together in a complete system.
-
Product
Grips and Fixtures for Force Gauges
-
AMETEK Sensors, Test & Calibration
We supply a range of grips and fixtures for the Chatillon force gauges. Below you will find a selection of our most popular grips and fixtures. If you cannot find what you are looking for, please contact us for a presentation of our full range.
-
Product
Vacuum Test Fixtures
Series 63
-
The VT Series 63 vacuum test kits provide both an affordable and versatile solution for printed circuit board testing requiring vacuum actuation and a Genrad 2270/71 interface. The VT Series 63 kits, available in Single and Dual Well models, incorporate a robust design which includes a variety of chassis sizes and depths for additional hardware and components used in Functional Test. Tooling holes on both the top diaphragm plate and probe plate for accurate drill datum. The interface will accommodate up to 11 I/O blocks with a single vacuum port.
-
Product
Emergency Battery Test Fixture
TA-60
-
This test fixture will allow servicing of the 60-1321-( ) series of emergency exit light power supply. These supplies are used in many aircraft to annunciate exit lighting when aircraft power failure occurs. The TA-60 test fixture is equivalent to the suggested test fixture in the OEM 60-1321 CMM. The four load lamps are conveniently placed behind an acrylic red lens for proper viewing while performing load test. The bench cable is provided as part of the test fixture.
-
Product
Cryogenic Millimeter-Wave / Microwave Test Fixtures and Calibration Kits
upj10
-
KEYCOM''s cryogenic millimeter-wave / microwave test fixtures and calibration kits are specifically optimized for testing the performance of patterns between the edges of printed boards(edge type) and circuit testing on the printed boards(probe type). They are also designed to minimize heat capacity by miniaturizing their dimensions so they cool off efficiently, and materials with low coefficient of linear thermal expansion such as invar are used for major parts where high dimensional stability is required. Their operating frequency ranges from DC to 110GHz.
-
Product
Mach Airspeed Test Fixture
TA-6055A
-
The TA-6055A is a Mach Airspeed Test Fixture built to support the testing and repair of the 2082 and 2083 series of Servoed Mach Airspeed Indicators (SMASI) used in some Boeing aircraft. These mach airspeeds are synchro driven and require a coarse and fine input for altitude and a third input for airspeed. This test fixture was designed around the test procedure and is interfaced with our TA-1001 panel which provides for two of the synchro sources and two Angle Position Indicators (API).
-
Product
Emergency Battery Power Supply Test Fixture
TA-61
-
This test fixture provides an interface to test and chargethe Radiant type RPS1-B Emergency Lighting power supply. The panel includes the switching required asdescribed in the CMM along with an analog currentmeter for monitoring the charging current. This panelprovides simple testing for the corporate flight departmentor DOM.
-
-
Product
Test Fixture
N1295A
Test Fixture
The Keysight N1295A Device/Component Test Fixture provides a low-cost solution to quickly and easily test packaged devices and components. For more advanced packaged testing needs, the Keysight 16442B Test Fixture provides more capabilities.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 580 x 400 mm (wxd)
CMK-04
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Manual Fixture Kit With Changeable Cassette, Max number of probes (2N) 1000 units, Max UUT 585 x 250 mm (wxd)
CMK-03
-
Linear click system with ball bearings, using gas springs.10 mm ESD-proof top cover with aluminum reinforcement bars.Steel base cabinet with detachable aluminum back and bottom panels.Detachable interchangeable case system with an 8 mm spring-loaded probe protection cover.Base cabinet fitted with a telescopic guide rail and catch.
-
Product
Burn-In Test Fixtures
-
Burn-in generally involves the extended operation of a product in a temperature-controlled environment. With possible humidity and supply voltage margining - the burn-in process can then be extended to include power stress (levels and on/off cycles) tests, high humidity environmental simulation as well as the classic "four corner test" of high voltage + high temperature, high voltage + low temperature, low voltage + high temperature and low voltage + low temperature.
-
Product
ICT/FCT-Fixtures Max UUT 370 × 300 mm (wxd)
CK-2-228X (Large IF) / 230532
-
The series of In-Circuit testers that are Teradyne for the 228x and TestStation are dedicated tools that rely on the tester hardware for diagnostics and test pattern delivery. The integration of the stand-alone BTS with the Teradyne ICT can enhance the system’s capability. In other words, it can provide access to additional tools. It provides the user with a common platform and portability of test patterns from stand-alone to ICT and later on to functional test and depot test stations.
-
Product
In-Circuit Test Fixture Design Services
-
An integral part of board test is the test fixture. Innovations in board technology may manifest themselves as challenges in test fixture design. Utilizing a creative & systematic design philosophy, Acculogic consistently delivers state of the art solutions for the most complex test interface problems.
-
Product
Pod/Nest Fixtures
-
Nest and Pod Fixtures are used to test components and sub-assemblies. They typically are built in an array and the devices under test are subjected to tests that simulate operating conditions or life-cycle testing. Test Head Engineering is experienced in providing nest and pod testers that meet the connectivity, ergonomic and mechanical requirements of component testing.
-
Product
Custom Test Fixtures
-
Cortek Test Solution’s design capabilities range from very basic to extremely sophisticated solutions. Developing custom test fixtures demands more engineering time as well as an in-depth knowledge of mechanical design, pcb test methods paired with precision machining. Our experienced engineers will evaluate your requirement and design innovative mechanical test fixtures to meet your application needs in both the R & D and production environments.
-
Product
Clamshell Type Mechanical Fixtures
-
Known in the ATE Industry as “Clamshell” type Test Fixtures, Semco’s Mechanical Test Fixture line is a cost-effective solution to test Printed Circuit Boards and Assemblies. This Test Fixture line is also available with the most widely used interfaces in the test industry.
-
Product
Fixture Interface Module 2 Test Matrices
OTP2 module no.193
Interface Module
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions. PXI is both a powerful and cost-effective platform for applications such as manufacturing test, military, aerospace, machine monitoring, automotive, and industrial test.
