PXI Interfaces
-
product
Isolated Serial To Analog Interfaces
ICS's Serial to Analog Interfaces are designed to provide isolated analog and digital drive signals to control power supplies and other devices. Available in rack mountable Miniboxes™ and IN OEM board versions. All of ICS's Serial to Analog Interfaces are fully IEEE-488.2 compliant and HP-IB compatible.
-
product
Analog I/O Interfaces
United Electronic Industries, Inc.
24 differential analog input channels Maximum sampling rate of 1000 Hz per channel 18-bit resolution ±3 µA accuracy 350 Vrms Isolation Dynamic autozero support Embedded averaging engine
-
product
Interface
EPMC-1553-8
Abaco Systems EPMC-1553-8 is the first PMC (PCI Mezzanine Card) module to offer 8 dual redundant MIL-STD-1553B Notice II channels. Available in commercial, ruggedized and conductively cooled versions with eight dual-redundant channels, the EPMC-1553 includes advanced API (Application Programming Interface) software that reduces application development time.
-
product
30 GHz differential probe with ProAxial interface
DH30-PX
30 GHz differential probe with ProAxial interface.
-
product
GPIB To ANSI X3.28 Interfaces
ICS's GPIB to ANSI X3.28 Interfaces adapt older devices that use the ANSI X3.28 devices to the GPIB Bus. All ICS GPIB Interfaces are IEEE-488.2 compliant and HP-IB compatible.
-
product
PXI Platform
The ruggedized enclosure provides an environmentally conditioned environment for rack mounted PXI equipment. Supports rack mounted PXI chassis. Hermetically Sealed case isolates PXI equipment from hostile environments as specified for military applications. The sealed enclosure allows the system designer to select any of the full line of PXI products without the need to Conformal Coat the cards/components. With the conditioned internal environment, there is no need to select PXI products which operate at an extended temperature range.
-
product
HDMI Interface Module
HDMI modules for RF Test Enclosures eliminate conducted and radiated interference while keeping data and power signals for the HDMI link untouched.
-
product
PXI Signal Amplifier
3180
Model 3180 was designed as a general purpose, wide band and high voltage amplifier, however, with specific applications in mind. It offers selectable gain of up to x50, with amplitudes of -90V to +90V and an output current of 150mA.
-
product
Serial To Digital Interface Boards
*ICS's Serial to Digital Interface boards provide the user with digital IO signals that can be user configured to match virtually any application. Both boards are available with high power relay drivers and with optional firmware designed to simplify switching applications.*All boards are designed for mounting inside a chassis.
-
product
4x IDC to 192 Pin Quadrapaddle
YAV90Q04
The interface YAV90Q04 permits to connect two YAV90096 boards to one 192-Signal contacts Quadrapaddle module. As the Mini-D 50 connectors let 2 free pins (1 and 26), these pins are interconnected to a test point, with the possibility of be grounded. Cable P/N J6200540: Mini-D-50 to Mini-D-50 IDC connectors with 400 mm flat cable.
-
product
Interface Cards, Cables, and Modules
Keysight Technologies Interface Cards, Cables, and Modules
-
product
Stand-Alone Programmer and Hardware Debug Interface
Cyclone MAX
Cyclone MAX is an extremely flexible tool designed for in-circuit flash programming, debugging, and testing of Freescale ColdFire V2/V3/V4, Power Architecture 5xx/8xx, Power Architecture 55xx/56xx (Nexus), and ARM (MAC7xxx) microcontrollers.
-
product
USB-8451, 250 kHz I2C, 12 MHz SPI I2C/SPI Interface Device
779553-01
The NI USB‑8451 is a master interface for connecting to and communicating with inter-integrated circuit (I2C), System Management Bus (SMBus), and serial peripheral interface (SPI) devices. With plug‑and‑play USB connectivity, the USB‑8451 is a portable solution to communicate with consumer electronics and integrated circuits. It also includes eight general-purpose digital I/O lines for a variety of applications, such as configuring the address of I2C devices or toggling LEDs. The USB‑8451 can be physically located more closely to I2C/SPI devices than PCI interfaces, reducing I2C bus length and minimizing noise problems. Additionally, the interface provides +5 V and GND to power circuits with no external power supply.
-
product
Smart GPIB Serial Interface Board
Model 4808
* Provides smart GPIB-to-serial path for serial devices with RS-232, RS-422 or RS-485 signals.* Provides all IEEE-488.2 functions and the Status Reporting Structure.* Smart firmware automatically passes GPIB data to serial device.* SCPI commands set serial configuration, GPIB address and user's IDN message.* On board voltage regulator for operation from 5 to 15 Vdc power.* Rear panel mounting eliminates cables.
-
product
PXI Attenuator Modules
Programmable RF Attenuators – accurate DC to 3GHz programmable attenuator has a 1dB step resolution, allowing it to adjust signal amplitudes for optimum measurement by other devices.Solid State Programmable RF Attenuators – available in triple or hex formats with bandwidths between 10MHz and 6GHz.High Voltage Attenuators – provide a convenient way of attenuating high voltage low frequency signals to levels that can be captured by other PXI devices without risk of damaging them.
-
product
PXI Chassis, 19-Slot
40-923A-001
The 40-923A includes all the features and performance required by the PXI standard and supports a control interface or embedded controller and up to 18 additional 3U peripheral modules.
-
product
13 GHz Differential Probe with ProLink Interface
DH13-PL
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
3U CompactPCI Serial Power Interface Board
046-201
Standalone Power-BP 3U 8HP to connect CPCI Serial power supplies to compactPCI Serial-BPs. The connection is made via cables.
-
product
MIL-STD-1553 PMC Interface Module
PMC-1553
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
-
-
product
ICD 3 Test Interface Module
AC164113
The Test Interface Board is an aid to isolate application interfacing problems when using the MPLAB ICD 3 (DV164035) as a debugger or programmer. Using the Test Interface Board and running confidence-test options under MPLAB IDE allows testing of the basic functions and signals of an MPLAB ICD 3. The diagnostic results under MPLAB IDE let the user know when the MPLAB ICD 3 is fully functional or if there is a malfunction. The MPLAB Online Help shows the user how to determine possible causes of hardware communication failures with the application.
-
product
Interfaces & I / Os
USBTucan is a USB-connected I / O box with digital inputs / outputs, analog inputs and a galvanically isolated CAN interface.
-
product
Virtual Interface Technology for 3D-IC Metrology
VIT
TSV profile (depth, top & bottom CD, tilt, SWA)-Residue Detection-RST-Copper Nail Height-Bump Height and Cu pillar height-Edge trim profile
-
product
PXI Optical Switching
Pickering's range of PXI optical switching modules include high performance multiplexers and insert/bypass switches. MEMS (Micro Electro-Mechanical Systems) switch technology offers higher performance and longer operational life compared to conventional prism based optical switching
-
product
I2C Interface for Digital I/O Control
EE301-I2C
Cable can be used with EE301-I2C or EE301-DCMI Model Numbers only. Cable + Power for Loads & Control Modules / Connects to a PC Parallel Port / Supports (2) Electronics Loads & Control Modules / 6' Power cable & 5' Data cable
-
product
Optical-Electrical Converter - PXI
O2E 1000 – 1400 Series
The O2E is a high bandwidth, broadband optical to electrical converter.Available in a range of configurations; choose from 1 or 2 channels, AC or DC coupling and various conversion gain and operating wavelength ranges.
-
product
MIL-STD-1553 Test & Simulation Interface for PCI Express
PCIe-C1553
Avionics Interface Technologies
Dual redundant, single, dual or quad stream configurationsSoftware selectable Transformer, Direct, and Bus Stub Coupling Modes - Concurrent Bus Controller, 31 Remote Terminals, & Bus monitor operation - Full error injection and detection - Multi-level triggers for capture and filtering - Ten high voltage (up from 30V) programmable DIO lines - IRIG-B time code encoder/decoder with free-wheeling mode - Real-Time recording and physical bus replay - x1 Lane PCI Express Host Interface (x4 Physical edge connector) - Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
product
PXI I/O Board
MZ-TrigIO
The MZ Trigger I/O Board (MZTIO) is a break-out board for the Pixie-16 PXI chassis backplane providing real-time access to Pixie-16 logic signals.
-
product
Power Interface Board 3 HE, 2PSU-Steckverbinder
106PIBM302-0000R
The PIB 3U 2 slot has two power connector P47 and connects to the backplane via power bugs with 6/32 screws. It is used to facilitate pluggable power supplies, headers, and utility connectors.
