PXI Interfaces
-
Product
Fibre Channel Test & Simulation Interface for PCI-X
PCI-X-FC4
-
Avionics Interface Technologies
Supports Point-to-Point, Switched Fabric, and Arbitrated Loop topologies - Two independent Fibre Channel ports - Two SFP sockets accept fiber or copper transceivers - Each port supports 1, 2, and 4 Gbps speeds - Comprehensive decoding of FC-1, FC-2, and Upper Layer Protocol (ULP) frames - Full Error Injection and Detection - IRIG-B Time Code Encoder/Decoder for Data Correlation - In-line Port Configuration for Transparent AnalyzerSupports multiple ULPs including FC-AE-ASM, FC-AE-RDMA, FC-AE-1553, and FC-AV - Compatible with AIT’s fcXplorer GUI Bus Analyzer Software
-
Product
ECU Interfaces
-
ECU Interfaces are devices that connect to an ECU microcontroller directly as a memory emulator or through the debug port interface. The interface is typically through a direct replacement of the microcontroller, memory emulation, or through the debugger port. The method can be driven by what is supported on the microcontroller. ATI offerings support all approaches:
-
Product
Interface Adapter. USB Solution
U2C-11
-
Dimax USB to I2C Bridge device - U2C-11 converts USB transactions to I2C Master transactions. U2C-11 turns your PC running Windows or Linux OS into comprehensive I2C Bus master.
-
Product
30 GHz Differential Probe with 2.92mm Interface
DH30-2.92MM
-
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
Product
CPCI Or PXI Communication Interface Board
MS 1706
-
*Memory and IO Read Write Cycles*External Interrupts*32 bit Data Bus*30 bit Address Bus*Control Signals for external interface*Four RS232 PORTS with full handshake signals*Four RS232/RS422 PORTS without handshake signals*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Nano Interface Unit
NIU2A
-
NAI’s NIU2A contains an integrated power supply, two function module slots and an optional ARM® Cortex®-A9 processor. This small, low-power unit is ideally suited for rugged military, industrial, and commercial applications. It delivers off-the-shelf solutions that accelerate deployment of SWaP-optimized systems — in less time, with NO NRE.
-
Product
Interface Between the Operator and the Sensor
Controller
-
The high-resolution touch screen provides best technical comfort and a virtual keyboard, including Latin, Asian and Cyrillic characters. A real time chart shows the trends and provides quick and clear information about the current process cycle, while the menu and display functions are clearly laid out. The user interface is intuitive and simple to use. Password-protected user administration and a stable, comprehensive data memory for all process values and events ensure the traceability, reliability and safety of the system.
-
Product
PCIe Card MX3 Copper Interface
OTP2 module no.183
-
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
Product
MIL-STD-1553 PMC Interface Module
PMC-1553
-
Avionics Interface Technologies
Dual redundant, single, dual, or quad stream configurationsTransformer & Direct Bus Coupling - Concurrent Bus Controller, 31 Remote Terminals, & Bus Monitor operation - Full error injection and detection - Multi-level trigger for capture and filtering - IRIG-B time code encoder/decoder - Ten high voltage (up to 30V) programmable DIO lines - Real-Time recording and physical bus replay - ANSI Application interface supporting C, C++, C#, and .NET development - Device driver support: Windows, Linux, VxWorks, & LabVIEW Real-Time (others on request) - Conduction-cooling and/or conformal coating available - Designed for extended temperature operations - 3.3v PMC (with 5V Tolerant I/O), 64-bit 33/66MHz - Rear (P14) and Front Panel Input/Output - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
Shuttle Bus cPCI Intelligent Interface Card
IIB-SB-CPCI
-
The Shuttle Bus cPCI is an intelligent interface card providing all Launch Data Bus, Ground Data Bus, and Multiplex De-Multiplex Multiple Remote Terminal capability to the Shuttle Bus, as required by NASA specification 84K01203 (Hardware Specification, Launch Data Bus (LDB) and Ground Data Bus (GDB) Interface Board).In summary, this card provides all features and functions required to meet the above specification, in a cPCI platform, with Simplex & Half-Duplex modes provided. Specific operational modes provided include for LDB_BCT, LDB_MRT, GDB_BCT, GDB_MRT, BUS_MON, MDM_MRT, Primitive and Calibration modes.
-
Product
USB Controlled Loudspeaker & Microphone Test Interface
AmpConnect™ ISC
-
AmpConnect ISC is an all-in-one audio interface that simplifies your test setup and operation. It is a single, rugged, rack-mountable piece of hardware containing a high-accuracy audio interface, impedance box, amplifier, headphone amplifier, 2 microphone power supplies and digital I/O. It replaces multiple hardware devices, connecting to your computer via a single USB cable, and it is fully controlled by SoundCheck. This simplifies setup and calibration, eliminates cabling and reduces connectivity errors, as well as reducing overall system cost.
-
Product
Premium Interfaces
-
Ramsey Electronics Premium Interfaces - USB, ethernet, video, and RF filtered power interfaces/rf data connectors
-
Product
3U cPCI Sensor Interface Unit
SIU35
-
NAI's SIU35 is a highly configurable rugged COTS system or subsystem ideally suited for military, industrial, and commercial applications that require high-density I/O, communication, Ethernet switching, and processing. The SIU35 uses up to five NAI field-proven, 3U cPCI boards to deliver off-the-shelf, SWaP-optimized COTS solutions that "Accelerate Your-Time-To-Mission."
-
Product
RS-232 to RS-422 Optically Isolated Interface Converter
Model 265
-
FEATURES: Eliminates Ground Loops; 19.2 KBPS at 2 Miles;TD and RD Indicators; Use in Pairs as Double Isolated Short Haul Modems; Use in Pairs as Double Isolated Short Haul Modem. Total isolation between RS-232 based systems and RS-422. Unique circuitry allows the RS-422 port to withstand surges exceeding 10 kilovolts.
-
Product
Easy-to-operate Interface
ANALYSIS 3N
-
ANALYSIS 3N provides an overall view of the whole monitoring points in the network.Each form on the interface symbolizes a DSR data logger. Numbers and names are shown at the topmost of each form, while real-time collected data in the middle, and communication, battery, working and storage status at the bottom. The background of an out-of-limit data turns to be red and keeps flashing.
-
Product
Interface, Kit USB
-
*Connects to a PC for data storage and retrieval from Greenlee digital multimeters*Allows retrieval of stored data and real-time logging and graphing*Retrieve stored data log from DML-Series*Export data to disk for analysis with any spreadsheet
-
Product
Locomotive Interface Gateway
LIG
-
Locomotive Interface Gateway (LIG) is a network communications and interface device that provides locomotive control-system data to third-party applications. The LIG is designed with an Open Message Interface which allows applications to access control-system data while providing locomotive system isolation to ensure the control system is not adversely impacted by third-party applications. The real-time parameters available from the LIG can be used to perform real-time health and status monitoring of a locomotive as well as real-time assessment of locomotive operator performance.
-
Product
General PXI Instrument
-
Platform features the industry- standard, 8-slot/14-slot/18-slot PXI/ CompactPCI backplane integrated into a 3U Eurorack enclosure with a bay for removable power supplies.
-
Product
PXIe-SMN Interface Card
-
Avionics Interface Technologies
2.125 Gbps Optical loop networkSingle-mode and Multi-mode optical interfaces supportedUp to 256 Shared Memory Network nodes supportedUp to 200 MByte/sec sustained data ratesMaximum 500 nS latency between nodesNetwork interrupts supportedSoftware Drivers available for Windows (7/8), Linux, LabVIEW Real-Time, and VxWorks
-
Product
Interface
RCNIC-A2PA3
Interface
The RCNIC platform is a high performance, 3U CompactPCI module (PMC on carrier card) for the AFDX/ARINC 664 protocol. With two independent ports for traffic monitoring, traffic generation, external triggering and analysis, the RCNIC provides high-resolution time-tagging of incoming packets simultaneously with highly accurate traffic generation. An IRIG-B receiver/generator is included for synchronization to an external IRIG-B time source and for synchronization between multiple RCNIC boards.
-
Product
PXI Oscilloscopes & Digitizers
-
Keysight's wideband digitizers can run at 3.2 GS/s, with up to2 GHz instantaneous analog bandwidth. They feature a Xilinx Virtex-6 FPGA that can implement different functionalities depending on which firmware option is selected.
-
Product
Intelligent Interface Card
IIB-1553-MMA
-
The IIB-1553-MMA is an intelligent interface card providing full MIL-STD-1553 test, simulation and bus analysis capability for the M-Module standard, with 1553A, 1553B, McAir and STANAG 3838 variants in one card. The IIB-1553-MMA supports concurrent Bus Controller (BC) and up to 31 Remote Terminals (RT) with Bus Monitor (BM). An additional stand-alone Chronological Bus Monitor (CBM) facility is also provided, withcomprehensive multi-level triggering capability. Full error injection capability is provided in BC and RT modes, with full error detection in BC, RT, BM and CBM modes. The unit provides a dual redundant 1553 interface. 2 Mbytes of dual ported RAM are provided. The board is supplied with C drivers in source code and Windows menu driven software as standard.
-
Product
ARINC 664 Part 7 XMC Interface Module
XMC-664-V2
-
Avionics Interface Technologies
Supports IEEE 802.3 10/100/1000 Mbit/s Full-Duplex Ethernet links - Utilizes SFPs to support both copper and optical interfaces - Simulates multiple ARINC 664 End Systems - VL traffic shaping and input VL redundancy management - Supports up to 4K Output VLs and 4K Input VLs - Supports up to 16K Sampling & Queuing output message ports and up to 16K input Sampling & Queuing message ports - ARINC 653, UDP, IP protocols managed onboard - IRIG-B time code encoder/decoder - Automatic message sequencing & periodic data generated onboard - Error Injection including Runt Frames, Short IFG, and Invalid MAC FCSDevice driver support: Windows, Linux, LabVIEW Real-Time (others on request) - Compatible with AIT’s Flight Simulyzer GUI Bus Analyzer Software
-
Product
PCI-8512, 2-Port, High‑Speed/FD CAN Interface Device
780683-02
CAN Interface
The PCI‑8512 is a high-speed controller area network (CAN) flexible data-rate (FD) interface for developing applications with the NI‑XNET driver. The PCI‑8512 excels in applications requiring real‑time, high‑speed manipulation of hundreds of CAN frames and signals such as hardware‑in‑the‑loop simulation, rapid control prototyping, bus monitoring, automation control, and more. The NI‑XNET device-driven DMA engine enables the onboard processor to move CAN frames and signals between the interface and the user program without CPU interrupts, minimizing message latency and freeing host processor time for processing complex models and applications.
-
Product
CAN interfaces and Analysers
-
CAN interfaces and analyzers with easy to use CAN bus software with optional support for OBDII, J1939, XCP/CCP, CAN transmit, and reading of DBC files.
-
Product
VXI Register Interface Board
VXI-5524A
-
*VXI Register Interface mates with user's PCB to form a B or C-size module.* 48 Digital IO Lines - Three 16-bit registers set as latched outputs or gated inputs.* 16 line bi-directional expansion bus for driving external logic.* Digital IO and VXIbus lines are 3.3V logic levels and are 5 V tolerant for compatibility with 3.3V logic and 5V VXIbus signals.* User selectable 3.3 and 5 Vdc puliup voltage on the digital IO lines for sensing switches etc.* The VXI-5524A board is a complete VXI-1 Rev 1.4 and VXI-2 compliant register-based interface.* User configurable model number, manufacturer ID, version and serial numbers.* Two companion component boards available for prototyping IC or RF assemblies.* Companion hardware kits available for building 1, 2 or 3-slot wide modules.
-
Product
One, Two, or Four Dual Redundant Interface MIL-STD-1553A/B Test & Simulation Module for PXI Express
PXIe-1553
-
Avionics Interface Technologies
1, 2, or 4 dual redundant MIL-STD-1553 bus interfaces Concurrent BC, multiple RT (31), and BM operations Full error injection and detection • Data capture filtering, 100% bus recording, and physical bus replay Multi-level Trigger for Capture/Filtering IRIG-B Time Encoder/Decoder Real-Time Recording and Physical Bus Replay Application interfaces supporting C, C++, C#, and .NET development Device Driver Support for: Windows, Linux, and LabVIEW Real Time (others provided on request) 10 high voltage (up to 30V) programmable DIO lines Flight Simulyzer GUI Analyzer software
-
Product
Bus Interface
IP-1553
-
MIL-STD-1553 is a versatile standardized bus interface. MIL-STD-1553 is robust featuring Manchester encoding and enough voltage swing to provide excellent noise immunity and reasonable throughput rates.
-
Product
GPIB Smart Serial Interface
Model 4866
-
* Adds an IEEE-488.2 compatible GPIB Interface to any serial device.* Provides all IEEE-488.2 functions and a Status Reporting Structure for the serial device.* Uses SCPI commands to set the serial configuration, GPIB address and user's IDN message.* Provides RS-232C single-ended and RS-422/RS-485 differential serial signals.* Operates with asynchronous serial devices, with standard serial devices and with 'smart' serial devices such as embedded computers or microprocessors.* 1 U high rack mount kit mounts one or two 4866s* Includes US 115 VAC Power Adapter, Manual and Support CD.
-
Product
Universal PCI, RS-422 Or RS-485 Serial Interface Cards
LPCI-COM422-8 and LPCI-COM485-8
-
These are eight-port, asynchronous, serial communication cards designed for use on the PCI bus. They support RS-422 or RS-485 communications. These cards offer the best combination of high-density and high-speed communications in a low profile form factor. The cards meet the MD2 Low Profile PCI Bus Specification and can be used in applications where space is at a premium, such as thin-client servers and high-density rack-mount servers. The LPCI line has been designed for use in retail, hospitality, and point of sale systems as well as the gaming and defense industries.
