Simulators
create what could be.
See Also: Simulation, Simulation Software, Simulation Testing, Emulators
-
product
Altitude Test Chamber
Aircraft and its components are subject to extreme pressure and climatic conditions during flights. These parameters have a significant influence on the functioning of individual components, and they must be monitored and measured for safety reasons. CME Altitude chamber allow for the testing of aerospace components in an environment with controlled pressure, temperature and humidity parameters. An altitude of 100,000 feet [10 mbar] can be simulated in the test space.
-
product
Advanced Three Phase Automatic Relay Test Sets
MP 3000 Series
Advanced three phase automatic relay test set. PC control through user friendly MPWIN Relay Test Software. High accuracy and high power over wide range. Suitable for IEC61850 GOOSE simulation, subscription and sampled value publishing. CE, FCC.
-
product
Sweating Thermal Guarded Hotplate
Sataton Instruments Technology CO., Ltd
Sweating guarded hotplate is the textile testing instrument for measuring of thermal and water-vapour resistance properties under steady-state conditions. By testing the thermal resistance and water-vapour resistance of textile materials, the tester provides a direct data for characterizing the textiles’ physiological comfort which involve a complex combination of heat and mass transfer. The hotplate is intended to simulate the heat and mass transfer processes which occur next to human skin and measure the hence transport properties in a steady-state conditions involving combinations of temperature relative humidity, air speed, and in liquid or gaseous phase.
-
product
Reach-In Altitude Test Chamber
Weiber Altitude Test Chamber combine temperature and altitude to test basic components or subassemblies designed for use in a variety of industries. With altitude test chambers, user can control the temperature environment for testing while simulating various altitudes from site level to 10,400 meters (25kPa). Altitude testing may be continued without temperature control up to 600,000 meters (0.1 kPa).High Low Temperature Altitude Test Chamber is used to test temperature and low-pressure altitude conditions simultaneously. Two common applications of High Low Humidity Altitude Test Chamber are testing of avionics or other aerospace equipment to simulate actual conditions, and simulate high-altitude conditions found in mountainous regions or other regions. All models are factory tested, with an ergonomic and maintenance cum user-friendly design. These CE approved test chambers are created with multi-layered insulation with double vapour barrier is of low 'K' factor, high density and of non-hygroscopic in nature. Weiber test chamber are made in accordance with the international standard. Weiber Test Chambers are GMP complaints and are also ISO and NABL certified.
-
-
product
ELECTRIC BRAKE FORCE METER WITH DYNAMIC LOAD SIMULATION AND CIRCUIT TESTING
MDTT9107
*Tests truck-side brake controller output and all towing-lighting functions without a trailer*Displays real-time brake controller output gain and timing*Quickly troubleshoots electrical circuits and ground condition*For use with aftermarket and integrated brake controllers*Microprocessor controlled; simulates trailer brake loads*25' cable allows one-man, in-cab testing of brake controller and all truck-side tow circuits*Use to verify that the vehicle’s adaptive (speed/load sensitive) brake-controller output is functioning properly
-
product
Thermal Load Boards
Thermal Engineering Associates, Inc.
A Thermal Load Board (TLB) is used to simulate an application printed circuit assembly (PCA) either before all the heat-producing components are available for mounting on the application PCA or if the heat-producing components require complex electronic circuitry to create heat within the components. The TLB is typically designed to be as mechanically and thermally equivalent to the application PCA and usually offers a way to vary the power dissipation of the elements that simulate the heat-producing components.
-
product
EMC Filter Synthesis Tool
EFsyn
EMC Filter Synthesis is a software tool for simulation and design of EMC filters. The new approach of this filter synthesis tool is based on simulating with the real values of the EMC filter components. Due to this, the EMC simulation considers the parasitics of the components.
-
product
EXG X-Series RF Analog Signal Generator, 9 kHz to 6 GHz
N5171B
Achieve faster throughput and greater uptime with the cost-effective performance optimized for manufacturing testPerform basic parametric testing of components and functional verification of receivers with industry-leading output powerThoroughly verify receiver performance by simulating complex analog modulation scenarios with multi-function generator capabilityMinimize downtime and expenses with self-maintenance solutions and low-cost repairs
-
product
PXI/PXIe High Density Precision Resistor Module, 4-Channel
40-297A-123
The 40-297A-123 (PXI) and the 42-297A-123 (PXIe) are 4-channel programmable resistors with a range of 1.5 Ω to 3.55 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PCI High Density Potentiometer Card 2-Channel, 12-Bit, 0 To 4k Ohm
50-296A-021-2/12
The 50-296A series are Programmable Potentiometer versions of the 50-295A Programmable Resistor cards with up to 9-channels of 8-bit resolution resistor chains in a single PCI slot. The flexible architecture allows the card to also be supplied as 12-bit, 16-bit or 24-bit resolution versions for applications requiring finer resolution, greater resistance range or higher channel count. The card is ideal for simulating the sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Programmable Resistor Card 4-Channel 2 Ohm to 127 Ohm - SPST
40-294-112
These PXI Programmable Resistor modules are available with either two channels of 16-bit, two channels of 12-bit or four channels of 8-bit resistor chains in a single 3U PXI module. The module is ideal for simulating sensors for control and management systems under test, allowing the user to verify system response in design verification or manufacturing test applications.
-
product
PXI Programmable Resistor Module
PXI Programmable Resistor Modules are wellsuited for simulating environmental conditions in hardwareintheloop(HIL) validation. The software included provides a simple user interface that accepts inputs in units of temperature or resistance, and configures the resistance across each channel. Each module uses a 37pin DSUB connector on the front panel, as well as a 2x2 MicroFit connector for easy connection to a PXI Digital Multimeter(DMM).
-
product
PXI/PXIe High Density Precision Resistor Module, 9-Channel
40-297A-026
The 40-297A-026 (PXI) and the 42-297A-026 (PXIe) are 9-channel programmable resistors with a range of 1.5 Ω to 26.7 kΩ. They are part of the 40/42-297A series of high density precision resistor modules and provide a simple solution for applications requiring accurate simulation of resistive sensors.
-
product
PXI Strain Gauge Simulator Module 6-Channel, 1k
40-265-206
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 1kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
product
Emissions Dynamometers
MD-250-M
Mustang has developed a low-cost, simple to use, easy-to-install heavy duty chassis dynamometer that can be used to simulate real-world driving conditions in a safe, controlled environment and can also be used for “static” diesel smog testing for regulatory purposes. This model is used in Diesel Smog Programs in Nevada and Colorado when combined with an approved opacity meter. The MD-250-M is a compact dynamometer with industry proven design features including 10.7-inch rollers, heavy duty spherical pillow-block ball bearings, welded structural steel frame, 7.5 hp calibration motor, and an industry standard air-cooled, Eddy Current Power Absorption Unit (PAU) for road-load simulation. The MD-250-M is available in both right and left hand configurations to accommodate different facility designs.
-
product
AC Electronic Load
The electronic AC loads cover a wide variety of different voltage, current and power ranges. All the AC loads are programmed with 11 different sine, square and DC waves. With 5 crest factor variations of each, a total of 55 waveforms are available. An external input is also provided to enable the user to amplify signals from a waveform generator.AC Loads allow real world operating conditions to be simulated. Typical applications include circuit breaker, transformer & UPS output testing along with general laboratory and research work.
-
product
Network Impairment Simulator
Testing system performance under realistic network conditions requires the introduction of impairments that could be expected to be seen on networks, especially public networks which are uncontrolled. There are a number of ways to do this. A basic method is to use network simulation devices that can emulate conditions expected to be encountered.
-
product
Test Suite
IEC 61850
The Test Suite is a group of Windows application that support IEC 61850 as well as IEC 60870-6 (TASE.2/ ICCP). New InSight functionality allows creation of custom graphical displays and scripted simulation design/debug via flowchart GUI. The Test Suite is comprised of three separate products.
-
product
DC Power Supply With Scope, Arbitrary Waveform Generator, And Automotive Application Features Bundle
E36154AGVX
The Keysight E36154AGVX consists of a Keysight E36154A DC power supply, a Keysight E36150ADVU Scope View and arbitrary waveform generation (AWG) capabilities, and a Keysight E36150ATMU Automotive Standards Testing Capabilities with Enhanced Programming Speed, ISO Preset Library, Playback Simulation and E-Logging features. The E36154A includes single-output and auto-range capabilities, 30V, 80 A, 800 W, and LAN and USB interfaces.
-
product
PXI Precision Programmable Resistor Modules
Pickering's PXI precision programmable resistor modules feature high setting resolution with excellent stability and accuracy through the use of innovative switching networks and software correction techniques. This also means all resistance values can be set - there are no missing values due to switch resistance or resistor tolerance. These modules are ideal for sensor emulation applications that require very fine adjustment and also have the capability of being set as open or short circuit to simulate faults in cabling systems. The range includes modules specifically designed for RTD and strain gauge simulation.
-
product
DC Source/Calibrators
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
-
product
Ozone Aging Test Chamber
Sanwood Environmental Chambers Co ., Ltd.
Sanwood , a 23 years of professional Ozone aging Chamber,Ozone aging Test Chamber, Ozone resistance test chamber, Ozone chamber,Ozone test chamber, manufacturersOzone Aging Test Chamber simulates and enhance the condition of ozone in the atmosphere to study the effects of ozone on rubber, and then identify and evaluate the method to resist ozone and aging for rubber, adopt effective anti-aging measures to enhance the life of rubber products.
-
product
Hydraulic Vibration Testers
HV-Series
L.A.B.’s HV Hydraulic Vibration Test Systems help you design high quality, cost-effective products and shipping containers by accurately measuring sensitivity to vibration. HV Systems are specifically designed to meet a wide range of ASTM, DOT, ISTA, ISO and federal standards for vibration testing. HV Systems are ideal for a wide spectrum of testing applications ranging from sine sweep tests to the most complex data real time simulation, or random reproduction applications.
-
product
Simulators
The Autonomous Air Combat Maneuvering Instrumentation System's unique combination of advanced air-to-air and air-to-ground combat training ensures air commands optimum utilization of flight hours and other valuable resources. Each system is fully customizable to address the skill sets of each operator. Key features include real-time kill weapons delivery, and electronic warfare attack notifications.
-
product
PXI/PXIe LVDT/RVDT/Resolver Simulator Module, 4-Banks
41-670-001-AABBCC
The 41/43-670-001 is ideal for the simulation of variable differential transformers (VDT), both linear (LVDT) and rotary (RVDT) types, as well as resolvers. It has four banks, each capable of simulating the output of a single 5 or 6-wire VDT or resolver, or dual 4-wire utilizing a shared excitation signal. This allows the module to simulate up to 4 channels of 5 or 6-wire or 8 channels of 4-wire.
-
product
PXI High Density Precision Resistor Module, 9-Channel, 2Ω to 122Ω
40-298-112
The 40-298-112 is a high density programmable resistor module with 9 channels which can be set between 2Ω and 122Ω with 0.5Ω resolution The 40-298 range provides a simple solution for applications requiring accurate simulation of resistive sensors. The 40-298 is available in a variety of resistance ranges and resolution capabilities that meet the needs of most functional test systems.
-
product
Shock Impact Testing
Environment Associates provides everything you need in drop shock testing — package/container, drop shock/impact systems and electro-dynamic simulated pulses. With our equipment, we specialize in tuned, matched impacts from 20 Gs to 30,000 Gs and from 30 ms to .02 ms in sine, saw-tooth, square-wave, gunfire and rotational cam pulses for almost any set of standards, or for any real-life condition. We can also handle a large range of weights and sizes. EA’s specialists will match the right test, equipment and configurations to your product. We also provide fixture design and special set-up solutions to mount and monitor your product’s functionality during and after testing.
-
product
MOSFETs, MESFETs, and Schottky Diodes
Semiconductor Module
The Semiconductor Module allows for detailed analysis of semiconductor device operation at the fundamental physics level. The module is based on the drift-diffusion equations, using isothermal or nonisothermal transport models. It is useful for simulating a range of practical devices including bipolar, metal semiconductor field-effect transistors (MESFETs), metal-oxide-semiconductor field-effect transistors (MOSFETs), Schottky diodes, thyristors, and P-N junctions.
-
product
PXI Precision Resistor Module 2-channel 1.5 to 2.9k
40-261-001
PXI programmable resistors featuring fine resistance setting resolution and excellent resistance stability and accuracy through the use of advanced switching networks and software correction techniques. The two modules in this range support two identical resistor channels t that can be set to values of between 1.5Ω to 2.9kΩ or 10Ω to 36kΩ with a precision of better than 2mΩ (this version) or 15mΩ (40-261-002) making them ideal for simulating sensors that can be accurately controlled to fine values.
