Cables
See Also: Cable Assemblies, Cable
-
product
Type X2 Double-Shielded GPIB Cable, 3 m
763061-003
24-Pin Male/Female GPIB to 24-Pin Male/Female GPIB, Stackable, Double-Shielded GPIB Cable - The 24M/F-24M/F X2 Cable, sometimes referred to as an X2 cable, connects your system to GPIB devices or interfaces for instrument control. The 24M/F-24M/F X2 Cable has 24-pin IEEE 488 male and female connectors, and the cable is double shielded with shielded plug/receptacles. The 24M/F-24M/F X2 Cable is also offered in different lengths.
-
product
500-Pin SEARAY Cable Assembly, Male to Male, 2 Amp, 0.5m, 250 Port
A500RMR-500RMR-4B050
The 500-Pin SEARAY connector is used on switching products to provide a very high density 2A connector solution that is suitable for use to 200VDC. This cable assembly is suitable for direct connection to Pickering Interfaces products using the 500-Pin SEARAY connector. Screwlocks are provided to secure the cable assembly to a mating product.
-
product
Hygrometer, 3 State Thermoelectric Cooler
CR - 5 Hygrometer
Buck Research Instruments, LLC
The CR-5 is a chilled mirror hygrometer that uses a 3-stage thermoelectric cooler (TEC) to enable frost point measurements of as low as 60 C, under favorable ambient conditions. It is configured as a transmitter module with an external sensor connected by cable up to 9 feet in length.
-
product
Micro Ohm Meter
The meter is used for testing cables under load condition. Available in various specifications and models, it is of great use in power generation sector.
-
product
Current Probes
XQ13
Beijing GFUVE Electronics Co.,Ltd.
The model XQ13 ac micro amp clamp on current probe is suitable for 10A-100A cable online measurement, it belongs to high performance current sensor field.
-
product
PPS Clamp Transformer
PPS2 provides power supply to the PD detectors installed on HV cable when low voltage AC power is not available. The PPS2 takes the required power directly from the High Voltage power line under monitoring by means of units clamped on the HV power cable(s).PPS2 is designed to withstand High Voltage line failure events such as temporary overload and short circuit conditions. An internal detection and self limiting circuitry guarantees that PPS2 and the connected equipment survives in case of such events.
-
-
product
Modular Breakout System for Hardware-In-Loop Simulation
Designed in partnership with OPAL-RT Technologies, this Modular Breakout System combines a BoB feature set with the added flexibility of an FIU. By mating the FIU chassis directly to the BoB using our plug-in modules, cabling is minimized, creating a more compact reliable design and improving signal integrity.
-
product
Coaxial Switch, DC to 4 GHz, SPDT, 75 Ohms
8762F
The Keysight 8762F brings a new standard of performance to 75-ohm coaxial components. Designed for ATE switching systems, the Keysight 8762F offers the performance demanded by the cable television distribution equipment and communications equipment industries. It gives the ATE system designer of telecommunications and cable distribution equipment the tools to design reliable, high performance switching interfaces. The Keysight 8762F uses a mini 75-ohm SMB connector for the coaxial interface. The mini 75-ohm SMB connector is designed to terminate RG-179 75-ohm coaxial cable. The Keysight 8762F is designed to work in virtually any system due to the range of voltage options covering 4.5 V to 30 Vdc available for activating the switch solenoids. The standard configuration of the switch includes solder terminals.
-
product
Cockpit Controls
TRIUMPH Mechanical Solutions produces cockpit controls and quadrants specifically designed to meet unique customer requirements. Our Electro-Mechanical Cockpit modules are frequently married to our push/pull controls to produce combined output devices. For example, a throttle quadrant with switch/transducer outputs and mechanical cable connections to an engine control system.
-
product
Cable Locators & Testers
PeakTech Prüf- und Messtechnik GmbH
This new cable detector consisting of a transmitter and a receiver is suitable for the search of voltage-free and voltage - carrying lines, as well as line interruptions and line tracking of surface and flush-mounted lines, pipe systems and even lines in the ground.
-
product
Series Dual Temp / Acceleration Sensors
TA102
Dual Temperature / Acceleration Output, Top Exit Connector / Cable, 100 mV/g, 10 mV/?C
-
product
Cable Tracing
Tone and Probe
The Amplifier Probe is designed to identify and trace wires or cables within a group without damaging the insulation. It allows for pin point identification even in the most congested cable bundles. Our unit can be used with any tone generator.
-
product
Cable Assembly, 9-Pin D-Type Female To Unterminated With Ferrules, 0.5m, HV
40-972-009-0.5m-FU-HV
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated.
-
product
Cable 96-Pin Female to 100-Pin Male Micro-D, 2m
40-973B-096-2m-FM
The 96-Pin to 100-Pin SCSI Style Micro-D Adaptor Lead is constructed from 7/36 (28AWG) Tinned Copper twisted pair wiring with Polyolefin insulation to minimise crosstalk. Metal Spring Latches are provided on the 96-Pin connector and 4-40 UNC screwlocks on the 100-Pin connector.
-
product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
product
Hand-Held Battery Load Tester, Alternator and Starter Tester
6026
135 Amp Fix Load Cables. Recessed meter helps protect this hand-held tester from damage and ensures more accurate and reliable outputs. Features easy to use clamps with 300 Amp jaws. Lightweight and easy to use. Imported.
-
product
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin FML D-Sub
540112020140
Cable Assembly, Receiver, QuadraPaddle, 20", 78-Pin FML D-Sub.
-
product
Probe And Test Adaptors Set (13PCS)
3601B
Peaceful Thriving Enterprise Co Ltd
1. Extra thin test probe.2. Flexible silicone cable.3. For use in conjunction with test probe.4. Bi-color test leads for polarity indication.5. High quality testing and test accessories.
-
product
sbRIO-9237, Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
781028-01
Non-Enclosed, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The sbRIO‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the sbRIO‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools. Non-enclosed modules are designed for OEM applications.
-
product
- 10Base-T to Multimode Fiber Optic Transceiver
Model 373
FEATURES: Extend Lan's over 1 mile; Full Duplex Plug and Play - no software; Uses industry standard fiber optic cables; Impervious to lightning and surges; Total electrical isolation; 10Base FL compatible. Now you can break the distance barrier of Ethernet based Local Area Networks and achieve total system safety from electrical interference and surges.
-
product
DMX Line Tester
DMXTSTR
The DMX Line Tester instantly displays the presence of +/- data on DMX lines and feed-through connectors. It serves as a perfect pocket sized tool for troubleshooting DMX512 cabling.
-
product
Field Meter
AP 201 Plus
The AP201 Plus field meter with total coverage of terrestrial TV bands, cable TV (CATV), 1st IF satellite and, if the relative option is inserted, the return channel 5-65 MHz.
-
product
CellCorder Battery Tester 'EU Series'
CRT - 400
The new CRT-400 is the latest version in the leading line of CellCorder battery test instruments. Lightweight, stylish, rugged and durable. Special features include new user-friendly operation, USB and IR data transfer, modem, graphical reflective LCD display for better contrast, and new cables and clamps.
-
product
2.96 mm (M) to 2.96 mm (M) 40 GHz RF Cable
GAU1-292M292M-XXX
UCINSTRUMENTS GAU1-292M292M-XXX 147A SERIES, FLEXIBLE CABLE 2.92MM(MALE)‐ 2.92MM(MALE)
-
product
Cable Assembly, 192-Pin Receiver, QuadraPaddle, 36", 160-Pin Female DIN
540069010240
Cable Assembly, 192-Pin Receiver, QuadraPaddle, 36", 160-Pin Female DIN
-
product
Chromatic Dispersion Measurement System
CD500
The CD500 is a chromatic dispersion measurement system for use in fiber and cable manufacturing, designed to produce accurate measurements quickly and with confidence. The CD500 uses a temperature-stabilized solid-state monochromator driven by a digitally derived RF frequency signal that allows the wavelength to be set and maintained with picometer precision and stability. Using a digital approach and employing the latest in DSP technology, the CD500 yields fast low noise drift-free results.
-
product
SHC68-68, 68-Pin VHDCI Male to 68-Pin D-SUB Female, Twisted Pair, Basic Shielded Multifunction Cable, 1m
191945-01
68-Pin Male VHDCI to 68-Pin Female D-SUB, Twisted Pair Cable with Basic Shielding, 1m
-
product
Cable Assembly. 9-Pin D-Type Male To Unterminated With Ferrules, 1m, HV
40-972-009-1m-MU-HV
A range of 9-Pin D-Type High Voltage cable assemblies with unterminated connections on one end, constructed from PTFE Type C insulated wire. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot breakwhen they are terminated.
-
product
Digital Video
DVI, HDMI, DisplayPort, and SDI products including DAs, switchers, matrix switchers, cables, adapters, and more for integrating digital video.
