Cables
See Also: Cable Assemblies, Cable
-
Product
Insulation Measuring Device According to DIN EN 61557-2 (VDE 0413-2)
-
PeakTech Prüf- und Messtechnik GmbH
This digital insulation measuring device is required for various measurements of cables, components and their insulation.
-
Product
20-Pin GMCT Cable, Female to Unterminated, Ferrules, 10A, 2m
A020GFR-F-0C200
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
Slip Ring Test System
-
This is a high specification tester that will measure many cable parameters. It measures cable resistance very accurately using the Kelvin 4-wire method. It also tests for shorts between pins at a low voltage. The next test is to measure insulation between connections at a higher voltage. This is carried out at up to 1500 Volts DC with resistances of 10 to 500 Meg ohms.
-
Product
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
540265010207
Cable Assembly
Cable Assembly, Receiver, Coaxial, 36", 6 SMA Plugs and 2 SMB Plugs
-
Product
Tone Coax Cable Generator
240 HAL
-
The AINES 240 HAL Tone Generator is a water resistant tone generator equipped with a weathertite 2 conductor modular cord and jack. The set can be connected to the Network Interface Device (NID) with either the two individual clips or the modular cord. This allows the CPE circuit to be viewed in both directions, towards the Central Office and towards the customer premise. In the event the CPE does not have a jack, but instead has a cord, plug the cord into the Model 240s jack and transmit tone!
-
Product
MS-M Style RF Connector Female Contacts RG179
40-969-701-FC
RF Connector Female Contact
This is a 30 piece kit of RF Connector Female Contacts for MS-M style Connector Housing, suitable for RG179 Co-axial Cable.
-
Product
8-Pin Power D-Type Cable, Male to Female, 0.5m
40-970-408-0.5m-MF
Cable Assembly
The 8-Pin Power D-Type cable assembly is constructed from 56/0.3 (12AWG) Copper Wire with PVC insulation. Screwlocks are provided to secure the connectors to their associated products.
-
Product
Cable Assembly 68-Pin Micro-D Male to Unterminated, Tinned Ends, 1m, Spring Latch
A068SMR-T-5B100
Cable Assembly
The 68-Pin Connector to Unterminated Cable Assy is constructed from 7/36 (28AWG) twisted pair wires with polypropylene insulation. The wires are colour coded to match the connector pin designation. The connector can be secured to the product by a Metal Spring Latch.
-
Product
Multiplexers (MUX)
WDM
-
It is highly desirable to reduce the number of cables required to communicate between spaces on Navy ships due to increased weight, cost and maintenance concerns. To reduce weight and expense, copper-based NTDS parallel and serial type cables can be converted to fiber optic and multiplexed using Wavelength Division Multiplexing (WDM) technology. WDM technology allows for multiple fiber optic wavelengths to be combined in a single fiber and then separated back to individual fibers at the distant end. Using Coarse WDM (CWDM) which utilizes wavelengths 20nm apart ranging from 1271 nm to 1611 nm, provides for up to 18 optical wavelengths to be combined into a single fiber. Optionally Dense WDM (DWDM) can be used allowing for up to 160 optical wavelengths.
-
Product
Insulation Testers
-
Whether you work on motors, generators, cables, or switch gear, the Fluke Insulation Resistance Testers provide noise-free, reliable results. With advanced performance, the insulation tester line is designed to be safe, simple to use and gimmick-free. A perfect solution for troubleshooting, commissioning, and preventative maintenance applications.
-
Product
Adapter/Nickel
WADP-NMSF
-
Warison provides wide range of wireless passive coaxial components, includes Adapters, Attenuators, Coaxial Cables Assemblies, DC Blocks, Filters, Isolators & Circulators, Probes & Terminations. With outstanding capability of development and design, Warison is able to custom the spec based on customer��s demand. All Warison��s products pass inspection and electronic performance test before shipping out. It is our principal to deliver the best solution to all our clients.
-
Product
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 20", 68 Pin Male VHDCI, 4 SMB Plugs
540103010130
Cable Assembly
Cable Assembly, Receiver, Mini Power/TriPaddle, 20", 20", 68 Pin Male VHDCI, 4 SMB Plugs.
-
Product
SEA CLIP™ Sensor & Aqua MER™ Meter
-
The SEA CLIP™ by Swain Meter is a high-quality, hydraulically actuated clamp-on DC ammeter for ROV. It is useful for measuring DC currents in subsea cables, cathodic protection systems, and subsea pipes up to 4” in diameter. The SEA CLIP™ can be used with an optional 200-foot cable to a topside meter, or in concert with the Aqua MER™ subsea meter at depths up to 6900 feet of seawater.The Aqua MER™ ROV meter is based on Swain’s proven MER2™ technology, specially adapted to the demanding requirements of the subsea environment and updated to provide RS-485 communication over twisted pair, or fiber optic data transmission protocols.
-
Product
Cable Assembly, 78-Pin D-Type, Female to Unterminated With Ferrules
40-972-078-2m-FU
Cable Assembly
A 78-Pin D-Type to Unterminated cable assembly constructed from 7/0.15 (26AWG) Silver Plated Copper Wire. Screwlocks are provided to secure the cable connector to associated products. Has a 45 degree cable exit away from pin 1. The 78-Pin Female connector option of this cable assembly is suited for direct connection to Pickering Interfaces products.
-
Product
Wireless Devices
-
Schweitzer Engineering Laboratories, Inc.
Wireless devices use radio signals to communicate and pass data over the air, eliminating the need for traditional cabling.
-
Product
Fiber Identifier
-
Fiber identifier is an essential installation and maintenance instrument which can identify the optical fiber by detecting the optical signals transmitted through them,during this process the fiber optic identifier generate no harm or damage to the fiber cable and it do not need opening the fiber at the splice point for identification or interrupting the service.This fiber identifier detects frequency tones at 270Hz, 1KHZ, 2KHZ, when traffic is present on the fiber under test, an audible tone can be heard. In the meantime, it can identify the traffic direction that indicated by LED with illumination.
-
Product
50 Ohm SMA to SMA Cable Assembly
40-977-521-0.25m
RF Cable Assembly
Pickering Interfaces offer a range of RF cable assemblies to complement our extensive range of PXI, LXI, PCI, VXI and GPIB switching products. All cable assemblies are made from high quality materials and use best practice assembly methods to ensure the cabling matches the performance of the switching modules they support.
-
Product
Cable, 96-Pin 1.27mm Pitch Female To Unterminated, Tinned Ends, Spring Latches, 2m
A096SFR-T-5B200
Cable Assembly
The 96-Pin 1.27mm pitch to Unterminated Cable Assy is constructed from 28 AWG Twisted Pair Tinned Copper wire with Polyolefin insulation. Crosstalk is minimised. Wires are colour coded for easy connection. Metal Spring Latches are provided on the 96-Pin connector.
-
-
Product
OTDR
-
Shaanxi Aitelong Technology Co., Ltd
Is a device that tests the integrity of a fiber cable and is used for the building, certifying, maintaining, and troubleshooting fiber optic systems.
-
Product
PCI Embedded Cables
-
Acromag provides a large selection of signal cables to complete the connection of the field wiring on the termination panel to the I/O board. We offer you a wide assortment of ribbon cables to accommodate the various pin and connector configurations.
-
Product
Flexible MiniPCI Express to 2 MiniPCI Splitter
SKU-069-2X
-
Flexible MiniPCI Express to 2 MiniPCI Splitter (Splitter) was designed to expand a modern motherboard (ATX, mini ATX etc.) that doesn’t have the MiniPCI interface. It allows you to connect up to two (2) 124-pin MiniPCI add-in boards to a motherboard’s standard MiniPCI Express connector.Splitter includes 2 MiniPCI Adapter boards, MiniPCI Express Host board and 2 Flat PCI Express Cables.
-
Product
X-Ray Fluorescence Analyzer
MESA-50
-
HORIBA has been selling the XGT-WR series of EDXRF analyzers for many years, providing screening measurements of samples containing hazardous elements such as Pb, Cd, Hg, Cr, Br, Sb, As for RoHS, ELV, and Cl for halogen free applications.XGT systems are used daily throughout the world. HORIBA has now developed the new MESA-50 EDXRF analyzer, based on its long experience with customer requirements and knowledge. MESA-50 provides user friendly operation and good performance. MESA-50 includes three analysis diameters, suitable for every sample, from thin cables and electronic parts to bulk samples. The combination of SDD detector and Digital pulse processor(DPP) changes the image of EDXRF.HORIBA's new MESA-50 supports ecological procurement; it contributes not only to EU RoHS and ELV compliance testing, but also regulatory work for many other countries.
-
Product
R1005050 Ribbon Cable, 2 m
182762-02
Ribbon Cable
The R100M-50F-50F Cable, sometimes referred to as R1005050, is a Y-shaped ribbon cable that connects to the 100-pin connector on NI digital devices. The R100M-50F-50F Cable is offered in different lengths.
-
Product
Cable Assembly, 37-Pin D-Type, Female to Unterminated With Ferrules, 0.5m
40-972-037-0.5m-FU
Cable Assembly
The 37-Pin Connector to Unterminated Cable Assy is constructed from PFA insulated 19/0.18 (21AWG) wire and can be secured to the product by screwlocks. The unterminated connections are coded to match the connector pin designation and include crimped on ferrules to ensure the wire strands cannot break when they are terminated. Please ensure appropriate electrical safety precautions are observed when using this product.
-
Product
RM-24999, 96-Pin Female DIN to 10-Pin Female RJ50, Rack Mount Terminal Block
785840-01
Terminal Block
96-Pin Female DIN to 10-Pin Female RJ50, Rack Mount Terminal Block - The RM-24999 provides RJ50 connectivity in a 1U rack-mount form factor for up to three bridge input modules. You can use SH96F-96M-5 Sensor Cables to connect to the PXI Express bridge input modules.
-
Product
Mobile App.
AnyWARE
-
The app connects to your IDEAL cable or network tester using Wi-Fi and transfers test reports to your mobile device. Once data is transferred, users can view the pdf reports and send them using their preferred file sharing method including email or file sharing app.
-
Product
Cable Assembly, 50-Pin D-Type, Female to Unterminated With Cut Ends, 1m HV, Exit Towards Pin 1
A050DF5-C-HA100
Cable Assembly
50-Pin D-Type HV Cable assemblies are constructed from 7/0.2 (24 AWG) Tinned Copper Wire with PTFE Type C insulation. The connector assembly can be secured to the mating part by a screwlock. The 50-Pin Female connector options of this product can be directly mated to a corresponding Pickering Interfaces switching product.
-
Product
CO2 Concentration Transmitter
T5241
-
CO2 concentration transmitter with 0-10V output is built in a durable watertight case. Output range is user adjustable. Large dual line LCD is an advantage. Display is possible to switch off. The device is supplied with CO2 probe with 1m cable. Cable lengths 2, 4 or 10 meters available optionally.
-
Product
Cable Assy 37-Pin D-Type F/F 1m
40-970-037-1m-FF
Cable Assembly
The 37-Pin D-Type cable assembly is constructed from 19/0.18 (21 AWG) Tinned Copper Wire. Screwlocks are provided to secure the cable to its associated products.
