-
Product
Fabric Pneumatic Bursting Tester
TF142C
-
TESTEX Testing Equipment Systems Ltd.
Fabric Pneumatic Bursting Tester, to determine the bursting pressure of fabrics uses pneumatic test method, including knits, woven fabric, non-woven fabric, laminated fabric and other craft-made fabric.A test specimen is clamped over an expansive diaphragm by a circular clamping ring, increasing compressed air pressure is applied to the underside of the diaphragm, causing distension of the fabric until the test specimen bursts, the bursting strength and distension are determined.
-
Product
Structural Testing Application Examples Using EDM Modal
-
Illustrated below are some customer applications in varying industries who are using the hardware and software by Crystal Instruments to analyze and understand the structural properties of their test specimen(s). Analyzing the modal characteristics namely natural frequencies, damping and mode shapes of the test unit further helps in improving the design to enhance the mechanical behavior of the test unit.
-
Product
Needle Microprobe
MT-29/2HT
-
Fast-response 29 gauge needle probe, (needle length is 2cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Climatic Test Chamber
-
HIACC Engineering & Services Pvt. Ltd.
Optimised heating & cooling system offers higher performance & energy efficiency. The test chamber can be customised suiting to different test standards. It comes with larger viewing window, ports for live specimen testing, visual alarm system, improved mobility and smaller footprint.
-
Product
Micro-Surface Microprobe
ICT-4
-
ICT-4 Micro-Surface Microprobe - For use on integrated circuits and other micro specimens. 0.013'' diameter .5'' straight stainless steel shaft; slightly protruding sensor bead to facilitate temperature probing. 5'' tubular handle fits micro-manipulators. Maximum intermittent temperature 200°C, continuouse use 100°C, Time constant 0.025 Seconds. 5 foot lead. Not isolated.
-
Product
HVFAA Horizontal Vertical FAA Flame Chamber
-
Atlas Material Testing Solutions
The Atlas HVFAA Horizontal Vertical Flame Chamber provides the most accurate means for determining the flammability of aircraft cabin and cargo compartment materials, liners and waste stowage compartment materials, and electric wire. The large volume chamber prevents oxygen depletion during tests. Three digital timers with remote control make specimen event timing precise and convenient. To ensure accurate and repeatable tests, an optional burner flame temperature verification kit is available. The HVFAA is the optimal instrument for conducting repeatable FAA flammability tests and is used in the FAA’s training facility.
-
Product
Vibration Test
-
Vibration testing determines the dynamic effects on component part of vibration within the frequency ranges and magnitudes that may be encountered during field service. Vibration, for example, causes loosening of parts or relative motion between parts in the specimen, producing objectionable operating characteristics, noise, wear, and physical distortion, and often results in fatigue and failure of mechanical parts.
-
Product
Torsion Testing Machine
-
JINAN PRCISION TESTING EQUIPMENT CO., LTD
Used to determine the torque load of specimens made of different materials in static tests.
-
Product
Walk-In Climatic Test Chamber
-
WEIBER climatic test chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. The climatic chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperaThe walk in option provides facility to test large sized, heavy weight specimen as well as the facility to test the specimen in bulk. Capacities ranging from 2000 to 10,000 Lt are available. Standard as well as customizable sizes and facilities are provided.
-
Product
Cylindrical Mandrel on a Stand
1500
-
The Elcometer 1500 Cylindrical Mandrel on a stand is a simple instrument for determining the elasticity, adhesion and cracking of dry paint on flat specimens, consisting of mandrel support which also serves as a test stand.
-
Product
Walk-in Environmental Chambers
EWS-SERIES
-
Mono-block/Pre-fabricated design EWS-Series Walk-in Environmental Chambers with custom-built features to meet testing needs of large-sized test specimens
-
Product
Taber Type Abrasion Tester
SG-P01T
-
The tester is used for cloth,paper,paints, plywood,leather,tile,glass,rubber etc.The testing method is executed to make specimen abraded by a pair of grinding wheels under the specified load.The weight of abrasion loss is the difference of weight for specimens before and after testing.
-
Product
VCS
Test Specimen Parameters
-
a program from the scope of ZETLAB VIBRO software suite. The update of the software suite ZETLAB VIBRO includes a new user-friendly interface as well as a wide range of new functions, allowing the user to configure parameters of the vibration test system with the maximal possible prevention of errors occurrence.
-
Product
Advanced Hydraulic Wedge Action Grips
2742 and 2743 Series
-
The Instron advanced hydraulic wedge action grips deliver controlled, constant gripping force using an external hydraulic supply across static and dynamic testing. They support capacities up to 600 kN (static) and 500 kN (dynamic), with interchangeable jaw faces for round or flat specimens. The design ensures jaw face positions remain fixed during gripping (eliminating preload), compensates for changes in specimen thickness, and is ideally suited for use with metals, composites, and plastics.
-
Product
Fully Automatic Rubber Tensile Testing System
-
Compactly Integrating Functions Required for Quality Control of Rubber Shimadzu Fully-Automatic Tensile Testing System This system provides full automation, from measurement of specimen dimensions, supply to the testing machine, and fixing of chucks to measurement of extension between standard lines and data processing. The system can be used for continuous nighttime testing, which helps save labor costs.
-
Product
Needle Microprobe
MT-29/1HT
-
Fast-response 29 gauge needle probe, (needle length is 1cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Plug-in Temperature Conditioners
PITC
-
The PITC, with a temperature range of -70 C to +177 C, was first introduced in the late 1950s by Bemcos Conrad/Missimer Division. Today, the modernized version of this system is the ideal solution where short run or infrequent tests are required, test specimens are unusual in size or shape, initial capital costs must be held low, or test needs are frequently changed.
-
Product
Ball Pressure Test
-
Premier Electrosystems' Ball Pressure Test is used to determine dimensional stability under stress at elevated temperatures. It analyses the relationship between the degree of deformation and the temperature when the test specimen is subjected to a constant load.
-
Product
High and Low Temperature Thermal Shock Chamber
HLST-500D
-
The specimen is placed in test chamber specimen which cannot be placed in high temperature chamber or low temperature chamber. High temperature chamber pre-heats the air and low temperature air chamber pre-cools the air. When doing the test of temperature changing from high to low, the low temperature chamber will blow the pre-cooled air to the test chamber. Then, the air in test chamber will reach your target temperature in several minutes (“recover time”). When doing the test of temperature changing from low to high, the high temperature chamber will blow the pre-heated air to the test chamber. Then the air in test chamber will reach your target temperature within the recover time.
-
Product
Needle Microprobe
MT-23/5HT
-
Fast-response 23 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Temperature shock test chambers test
TSS series
-
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
