-
Product
Multi-Specimen Fatigue
-
TA Instrument’s Multi-Specimen Fatigue Instruments are designed to accelerate fatigue studies for a variety of materials, subcomponents and complete devices. With the capability of simultaneously testing up to 16 specimens at up to 100 Hz, users can generate S/N curves faster and with higher statistical confidence levels than ever before. In this system, proven and refined technologies come together to quickly and confidently deliver results.
-
Product
Specimen Preparation Equipment
-
Thermal damage can be reduced by cooling the specimen with liquid nitrogen during processing.Designed to suppress the consumption of liquid nitrogen, allowing long cooling periods.Rapid cooling of the specimen while immersed in liquid nitrogen. Return to room temperature. Designed to allow parts to be detached.
-
Product
Surface Water Absorption Tester
TF167
-
TESTEX Testing Equipment Systems Ltd.
Specimens are placed at an angle on the base of the apparatus. After water flows down the surface of each specimen, the amount of water retained by each specimen is measured. Six specimens are tested, three on the face of the fabric and three on the back of the fabric. The six observations are averaged to determine the surface water absorption of the fabric.
-
Product
Fabric Pneumatic Bursting Tester
TF142C
-
TESTEX Testing Equipment Systems Ltd.
Fabric Pneumatic Bursting Tester, to determine the bursting pressure of fabrics uses pneumatic test method, including knits, woven fabric, non-woven fabric, laminated fabric and other craft-made fabric.A test specimen is clamped over an expansive diaphragm by a circular clamping ring, increasing compressed air pressure is applied to the underside of the diaphragm, causing distension of the fabric until the test specimen bursts, the bursting strength and distension are determined.
-
Product
5 KN Split-Drum Grips For Rope
-
These lower capacity 5 kN (1,100 lbf) split-drum grips are suitable for testing the tensile properties of rope and string with a diameter of 3 mm (0.12 in) or less. The diameter of the drum in the grips is 50 mm (2.0 in) and a spring mechanism is used to apply a clamping force through the split-drum to the specimen during testing.
-
Product
Temperature shock test chambers test
TSS series
-
The operating principle of Schocktestprfschrank based of two superposed test rooms (top hot chamber, cold chamber below), between which a car with the test specimens is moved up and down by the large thermal shock test equipment may be subjected
-
Product
Scott Type Crease-Flex Abrasion Tester
TF119
-
TESTEX Testing Equipment Systems Ltd.
Scott Type Crease-Flex Abrasion Tester, to determine the crease-Flex abrasion resistance of leather, rubber cloth etc. The force loaded on specimen, distance between grips and the two-way distance can be adjustable. And the force loaded on specimen is of spring type.
-
Product
Extensometers
-
Extensometers measure strain, the change in length of a specimen divided by the original length (gauge length) of the specimen. Tinius Olsen offers wide range of extensometers based on your testing needs including video, optical and physical contact with specimen.
-
Product
Static Axial Clip-On Extensionmeters
2630-100 Series
-
The Instron static axial clip-on extensometer delivers precise strain measurement for static tests by quickly clipping to specimens (metals, plastics, composites) with minimal attachment force. Its rugged cross-brace design resists distortion, includes built-in over-extension protection, and meets ASTM E83 / ISO 9513 standards — making it a reliable, high-accuracy option for general and temperature-controlled testing.
-
Product
Scanning Electron Microscopy
SEM
-
Materials Evaluation and Engineering
JEOL JSM-6610 LV LaboratoryScanning electron microscopy (SEM) uses electrons for imaging to obtain higher magnifications and greater depth of field than light microscopes. The instruments at MEE are capable of variable-pressure, or low vacuum, SEM (VPSEM), as well as traditional high-vacuum conditions for sample observation. VPSEM is a specialized method using a variable-pressure sample chamber that allows direct evaluation of samples that are not readily examined with a traditional high-vacuum SEM. Nonconductive or vacuum sensitive samples that would typically require additional sample preparation can be directly analyzed in VPSEM without the need for additional sample preparation, such as carbon or metallic conductive coatings. This reduces both sample preparation time and distractions in microanalysis. Our laboratory also has a field emission SEM (FESEM) for critical high-magnification work and low-voltage (LVSEM) applications. Each instrument has a spacious sample chamber that can accommodate large and irregularly-shaped specimens and accessories for feature dimensional analysis and chemical microanalysis.
-
Product
VisualIMPACT Software
-
CEAST VisualIMPACT software is designed to control CEAST Pendulums and Drop Tower Series, manage tests and offer a user-friendly interface when using the Data Acquisition System. It records force and absorbed energy data related to impacts, visualizes and helps analyze the results and calculates resilience. The operator is guided through parameters setup by means of tables describing strikers and specimens that are filtered according to the test type and international standard selected. In the case of instrumented tests, many possibilities for data analysis and visualization are made available. The results are shown through comprehensive and customizable graphs and can be filtered by break type (only specimens with a selected break type are shown). Working with groups of test, the software performs a statistical analysis, and the operator can pick and discard single test results. Different measurement units can be selected. It is possible to print reports and to export data totally or partially. Recent improvements include the possibility to set a number of user profiles, including graphic settings, default printing options, advanced parameters for data analysis and so on, switching quickly from one another when looking at results. The introduction of a new Data Acquisition System (CEAST DAS 64K) in the Impact product line has also triggered a number of new capabilities for the SW, which is now able to process a more comprehensive calibration file for instrumented tups and hammers and manage DAS configurations with a wider range of data acquisition channels.
-
Product
Electrodynamic Vibration Test Systems
DC-series
-
Depending on the reference PSD or other operating conditions such as the specimen, one part of the controlled response may deviate from the reference PSD
-
Product
Double Pin 8
INO012946
-
The Double Pin 8 is used to connect two MECHANICS components with the hole 8. With our MECHANICS construction kit, you have your fixtures, test specimens, and test setups firmly under control. The numerous, easy-to-use components work perfectly with your SMARTTESTER® testing system. Due to the identical connection technology and tools, the individual parts fit seamlessly together. This allows you to realize your test scenarios in record time and adjust them super quickly.
-
Product
Electrodynamic Shakers
R-Series
-
The R-Series vibration test systems are designed to provide reliable performance for medium and high force applications. The R-Series Shaker Armature incorporates a multi-ribbed design, which provides maximum stiffness and minimum weight, resulting in a high acceleration to specimen weight ratio and impressive acceleration and frequency performance.
-
Product
Clamp 80
INO003524
-
Clamp for securing test specimens using a clamping screw.Includes down-pull pin 8-23.
-
Product
50 KN Capstan Grips For Heavy Cloth
-
These 50 kN (11,000 lbf) grips use a split drum and capstan to firmly hold specimens that have a tendency to slip, such as heavy cloth and belts, during tensile testing.
-
Product
200 N And 1 KN Roller Grips
-
This roller grip set includes both 200 N (44 lbf) and 1 kN (220 lbf) roller grips for tensile testing elastomeric ring specimens. The 200 N grips have a 4.5 mm (0.18 in) diameter roller. The diameter of the roller on the 1 kN grips is 25 mm (0.98 in).
-
Product
Rubber Plasticity Meter
DRK209
-
Shandong Drick Instruments Co., Ltd.
DRK209 is applicable to test plasticity property when the specimen bears 49N pressure. The meter is used to test plastic value and restoration value of raw rubber, plastic rubber and rubber.
-
Product
Pin Grips For Flat Specimens
-
Pin grips are very user friendly and are designed for conducting tensile tests of hard metal plate specimens that are difficult to grip. Specimens are held within the grips by passing pins through holes in the specimens.
-
Product
Microbiology Testing Products
-
Bio-Rad microbiology products are a diverse array of: Culture media, rapid assays, biochemical tests, direct antigen detection, immunological serotyping, latex agglutination, and other tools for the recovery, growth, identification, and measure of microorganisms from clinical specimens.
-
Product
Ultra Light High Voltage DC Test Sets
-
This Compact power supply/test set can perform all laboratory and field tests of DC Hipot. A flexible High Voltage Cable is provided at the back for connecting to the test specimen. Available in Rack Mount as well as portable design.
-
Product
High-Temperature Extensometers < 1000°C Capacitive
2632 Series
-
Is typically used in hot tensile applications with tube type furnaces and consist of a separate measuring unit and suspension arm assembly. The measuring unit uses an LVDT with a fixed travel that remains outside of the furnace, the arms are located mostly inside of the heating system and attach the specimen to the measuring unit.
-
Product
MMIWG2-B
100277
-
Unlike our first MMIWG version, our MMIWG2 series offers you even more ergonomics thanks to our new Top Loader function. After unlocking the cassette, it can be easily removed upwards, whereby it is no longer necessary to open the housing to change the cassette. The simple and time-saving cassette change thus enables you to further reduce set-up times and guarantees even faster further work on the test specimen. This optimisation also reduces the mechanical load on the basic fixture wiring. The MMIWG2-B is prepared for safety switches with guard locking as well as for electrical interlocking.
-
Product
High Temperature Axial Extensometer
-
Jinan Testing Equipment IE Corporation
A precision scientific instrument used in materials testing to measure physical deformation (axial strain) on a test specimen under high-heat conditions, such as inside a testing furnace or during induction heating.
-
Product
Climate Control Test Chamber
-
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
Product
Quick Change Mold
AIM
-
These types of specimen tests are commonly used to determine the key properties of a material, such as tensile strength, Izod and Charpy impact strength, hardness, flammability, shrinkage and gloss/color matching.
-
Product
Averaging Clip-on Extensometer
2650 Series
-
The Instron 2650 Series Biaxial Extensometers are ideally suited for testing a wide range of materials, including polymer matrix composites, metals, and plastics over a range of temperatures. Two sensors measure axial strain on opposite sides of the specimen. Versions are available which provide either a single averaged axial output or 2 independent axial outputs. The extensometers meet the calibration requirements of ASTM E83 class B1, ISO 9513 class 0.5, and ISO 527.
-
Product
Flexible Implantable Microprobe
IT-1E
-
IT-1E Flexible Implantable Microprobe - For ultra fast measurements and for use on micro-size specimens. Similar to our most popular IT-18 microprobe but the sensor bead is exposed, resulting in the same ultra-fast response time of the IT-23 but with the Teflon™ sheath strength of the IT-18. Time constant 0.005 seconds. Tissue Implantable with a 18 gauge needle (supplied). Rather fragile at tip. Coated in Teflon™. Maximum Temperature 150°C. Isolated. Probe tip diameter .011", sheath diameter .025'' . 3 foot lead.
-
Product
MMIWGT-A
-
With our MMIWGT-A, we offer you a compact version of a mechanical change system. Thanks to the integrated top loader function, this adapter still guarantees the proven ergonomics that our MMI series promises. Just as with our new MMIWG2 series, the cassette of the MMIWGT-A can also be easily removed upwards after unlocking, meaning that it is not necessary to open the housing. The simple and time-saving cassette change enables you to further reduce set-up times and guarantees even faster continuation of work on the test specimen. This optimisation also reduces the mechanical load on the basic adapter wiring.
-
Product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
-
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.





























