Showing results: 61 - 75 of 318 items found.
-
Sataton Instruments Technology CO., Ltd
Horizontal flame resistance tester is design based on FMVSS 302 to determine the burning behavior of materials as interior in motor vehicles by calculating the burning rate of the specimen after ignition by a small flame. Exposed to a certain flame for specified time, the specimen which is clamped in a U shape holder will be measured for the burned distance and time taken to burn this distance. The tester is particularly important for assessing safety of the materials used in the passenger compartment.
-
ACMAS Technologies Pvt. Ltd.
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
American Environments Co., Inc.
A Test Specimens can be evaluated in two different modes in reference to acoustic noise: The Test Specimen's response to acoustic noise and the Test Specimen's generation of acoustic noise.
-
Martin Testing Laboratories
Shock testing typically involves calibrated, repeatable, violent events. The resulting energy is then absorbed transferred through the test specimen or Device Under Test (DUT)
-
CV-series -
IMV Corporation
CV-series is suitable for transportation tests. The lateral support stiffness and maximum displacement of the CV-series are large enough to be accommodate vibration tests of the specimens with high center of gravity.
-
Jinan Saicheng Instrument
Oxygen permeability is the ability of a barrier material to oxygen to permeate through it in a specific time. Oxygen permeability may vary with temperature, humidity, pressure and specimen thickness.
-
Atico Export
The Hamburg Wheel-Tracking Tester is used to test submerged, compacted Hot Mix or Warm Mix Asphalt specimens as per standard.The device consists of a reciprocating wheel that is rolled over the specimens while measuring the rate of permanent deformation. A constant load of 705 N ±4.5 N is applied to the specimens with a sinusoidal wheel speed of 1 ft/sec in a constant temperature controlled water bath up to 70 °C (± 1.0 °C). An LVDT jig is used for continuous measurement of permanent deformation along the path of the rolling wheel. Accommodates cylindrical or slab specimensSoftware for automatic determination of Stripping inflection PointNumber of passes to SIP, number of passes to failure and other calculated parametersStainless steel construction with temperature controlled water bath up to 70ºC
-
AIM -
Tinius Olsen
These types of specimen tests are commonly used to determine the key properties of a material, such as tensile strength, Izod and Charpy impact strength, hardness, flammability, shrinkage and gloss/color matching.
-
SURFTENS AUTOMATIC -
Optik Elektronik Gerätetechnik GmbH
Automatic measuring instrument for contact angle and free surface energy with motorized pump, automatic drop placement and motorized specimen table (200 x 200) mm.
-
MT-29/3HT -
Physitemp Instruments
Fast-response 29 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
MT-23/3HT -
Physitemp Instruments
Fast-response 23 gauge needle probe, (needle length is 3 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
MT-23/5HT -
Physitemp Instruments
Fast-response 23 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
MT-29/5HT -
Physitemp Instruments
Fast-response 29 gauge needle probe, (needle length is 5 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
MT-26/2HT -
Physitemp Instruments
Fast-response 26 gauge needle probe, (needle length is 2 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
MT-26/4HT -
Physitemp Instruments
Fast-response 26 gauge needle probe, (needle length is 4 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.