-
Product
Clamp 40
INO008659
-
Clamp 40 for securing test specimens using a clamping screw.Including pull pins 8-23.
-
Product
High Temperature Axial Torsional Extensometers (1200 C or 1600 C)
Model 7650
-
Jinan Testing Equipment IE Corporation
Model 7650 extensometers are primarily used on round specimens tested in bi-axial test machines capable of simultaneous axial and torsional loading. All models are capable of bi-directional displacement in both axes and may be used for strain-controlled fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650 models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to minimize crosstalk between axes and to provide high accuracy, high resolution measurements. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods with conical rod tips for specimen contact when testing to 1200℃(2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.
-
Product
Needle Microprobe
MT-26/2HT
-
Fast-response 26 gauge needle probe, (needle length is 2 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
Falling Dart Impact Tester
FDI-01
-
Jinan Leading Instruments Co., Ltd.
FDI-01 Falling Dart Impact Testeris applicable in the impact result and energy measurement of the falling dartfrom a certain height against plastic films and sheets with a thickness less than1mm, whichwould result in 50% tested specimen failure.
-
Product
Scott Type Crease-Flex Abrasion Tester
TF119
-
TESTEX Testing Equipment Systems Ltd.
Scott Type Crease-Flex Abrasion Tester, to determine the crease-Flex abrasion resistance of leather, rubber cloth etc. The force loaded on specimen, distance between grips and the two-way distance can be adjustable. And the force loaded on specimen is of spring type.
-
Product
Leak Tester
LSD-01A
-
Jinan Leading Instruments Co., Ltd.
LSD-01A Leak Tester is applicablein leak testing of pouches, bottles, pipes, cans and boxes of foodstuff,pharmaceutical, medical, daily chemistry, automotive, electronic components, stationary and other industries. It’ s also applicable in the leak testing ofthe specimens after falling tests and pressure resistance tests.
-
Product
Zipper Tester
-
TESTEX Testing Equipment Systems Ltd.
Zipper Tester, to determine the resistance to reciprocation of zipper (slide fastener), the test specimen is subjected to a specified number of cyclic operations whilst under lateral and longitudinal tension. Zipper Tester complies with BS 3084, CNS -1083, QB/T2171-1995, etc. Please contact us for more about information about pull test procedure.
-
Product
Pre-Assembled Plate 400×552
INO014880
-
With our MECHANICS construction kit, you have your fixtures, test specimens, and test setups firmly under control. The numerous, easy-to-use components work perfectly with your SMARTTESTER® testing system. The identical connection technology and the same tools fit the individual parts seamlessly together. This allows you to realize your test scenarios in record time and adapt them super quickly.
-
Product
Needle Microprobe
MT-29/1HT
-
Fast-response 29 gauge needle probe, (needle length is 1cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
1 KN Pneumatic Flat Grips For Foil
-
These 1 kN pneumatic flat grips are designed for tensile testing metal foils. Unique grip features include a very rigid structure, which reduces swivel of the grip faces during testing, and specially shaped flat grip faces. As with all pneumatic grips, these grips allow quick specimen clamping with a repeatable clamping force.
-
Product
Needle Microprobe
MT-29/2HT
-
Fast-response 29 gauge needle probe, (needle length is 2cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
CT-NANO
-
The CT-NANO is a fully operating scanning electron microscope with capabilities of Nano-CT measurements on specimen like light-metal-alloys and fiber composites.
-
Product
Needle Microprobe
MT-26/4HT
-
Fast-response 26 gauge needle probe, (needle length is 4 cm) for instant readings in tissue, semisolids, liquids. Also for very small specimens, powders and materials. Needle tip is sealed to ensure only stainless steel contacts specimen. Max. temp. 200°C. 5 ft. lead. Smallest microprobes give fastest reading. Short probes are easier to insert and last longer. Type #'s indicate needle gauge and needle length in cm.
-
Product
1 KN Capstan Grips For Yarn And Wire
-
These capstan grips are applicable for tensile testing yarn and metal wire with thickness less than 3 mm (0.12 in). Flat grip faces are used to hold the specimen. The grip faces are opened and closed by a cam with an operating lever. Ease-of-use and simple design are advantages of these 1 kN capstan grips for yarn.
-
Product
Resonant Testing System
-
Originally designed to precrack specimens for fracture mechanics, the current versions offer much more possibilities due to a modular concept:*Bending up to 160 Nm*Tension/Compression up to 8 kN*Torsion
-
Product
Benchtop/TableTop Chamber
-
HIACC Engineering & Services Pvt. Ltd.
Built with corrosion-resistant stainless steel, the test space can hold specimen up to 100 kg. The refrigeration system uses low GWP refrigerant and meets all statutory standards. The chamber also comes with removable humidity water tank and direct water connection is also available
-
Product
Environmental Test Chambers
-
Dongguan Kejian Instrument Co., Ltd.
UV accelerated weathering test chamber simulates damaging effects of long term outdoor exposure of sunlight, heat, moisture on materials and coatings. It exposes specimen to varying conditions of weathering- ultraviolet radiation, moisture and heat to test the performance and improve the quality.
-
Product
Falling Dart Impact Tester
DRK135A
-
Shandong Drick Instruments Co., Ltd.
DRK135A Falling Dart Impact Tester is applicable in the impact result and energy measurement of the falling dart from a certain height against plastic films and sheets with thickness less than 1mm, which would result in 50% tested specimen failure.
-
Product
1 N Clip Grips
-
These very low force 1 N (0.22 lbf) clip grips are for tensile testing fibers, tapes, and other similar shaped specimens. They are designed for use with 50 N (11 lbf) and below load cells.
-
Product
Low-Temperature Impact Device
DWC-1
-
This low-temperature impact device is compliance with standard requirement of IEC60245, IEC60227, IEC60540, GB5013-2008, GB5023-2008 and GBT2951-2008. It’s used to test all kinds of PVC sheathed cable, wire, soft wire and no sheath of parallel soft PVC insulated impact resistance at low temperature. Specification: • Working temperature: -15℃±1℃ • Impact height: 10~200mm adjustable • Length of specimen: 5D~150D • Material: 304 stainless steel • Completion time once: 3~5s • Completion number of units for once: ≥2pcs • Weight: 100/200/300/400/500/600/750/1000/1250/1500g • Low temperature box to match additionally
-
Product
Pneumatic Side Action Tensile Grips
2712-04x Series
-
Instron’s pneumatic side-action grips provide a high-performance, repeatable, and safe gripping solution for a broad spectrum of materials — from fine wires, fibers, textiles and foils to plastics, elastomers and components — via air-actuated clamping that maintains constant force even as specimens deform. With quick, tool-free jaw face changes, optional alignment and centering devices, adjustable opening and flow control, and integrated safety features (e.g. jaw face shields), these grips are engineered for throughput and reproducibility operator protection in tensile testing applications.
-
Product
Gold Detectors
-
Be prepared to dig deeper than ever before! With a Minelab Gold Detector you''ll find the elusive gold nuggets that others are missing! Minelab Gold Detectors are the FIRST CHOICE for: Professional gold prospectors, Small scale artisanal mining, Serious holiday gold prospecting, Weekend enthusiasts, Gold specimen collectors.
-
Product
Inverted Microscope Platform
Axio Observer
-
In life sciences research you come up against new challenges every day. That’s why you want a flexible microscope system that can be tailored to your needs. ZEISS Axio Observer is your inverse platform for demanding multimodal imaging of living and fixed specimens. Combine Axio Observer with a wealth of technologies and refine it to support your experiments precisely.
-
Product
Climatic Test Chamber
-
HIACC Engineering & Services Pvt. Ltd.
Optimised heating & cooling system offers higher performance & energy efficiency. The test chamber can be customised suiting to different test standards. It comes with larger viewing window, ports for live specimen testing, visual alarm system, improved mobility and smaller footprint.
-
Product
Max-Hand Durometer
Model 3000
-
The Max-Hand 3000 durometer is Rex Gauge Co.'s latest innovation for the testing of specimens with creep. The Max-Hand 3000 has a max- hand and an active hand for observing the creep characteristics of a specimen. What makes the Model 3000 unique is the magnetic-drag maximum reset mechanism. Available ASTM, DIN, ISO Types: A, D.
-
Product
Motorized Constant Loader
CLE-150 Series
-
When we measure the hardness of rubber test specimen etc. with durometer, we have the possibility to make an error for the result of the measurement. To make solution for such an important factor fo the error, CLE-150 Series is employed the motor driving system for the descent speed control, and then we could realize to measure the hardness of constant speed and constant pressure that is precise and reproducible.
-
Product
Long-Stroke Tensile Testing System For Vulcanized Rubber
-
Capable of Measuring Even Specimens with a Large Break Strain A tensile test method for vulcanized rubber is stipulated in JIS K6251 (Rubber,vulcanized or thermoplastic-Determination of tensile stress-strain properties). One of the properties of vulcanized rubber is significant elongation. This long-stroke tensile testing system for vulcanized rubber has a long stroke that is required for calculating these tensile characteristics of rubber, and accommodates dumbbell specimens Nos.1 through 6 stipulated in JIS K6251.
-
Product
Generators
Classical Shock
-
Software Classical shock is used for testing specimen resistance to shock impact. As the Software Classical shock is activated, at the output of shaker control system ZET 017-U there is formed a signal with pre-set parameters. Types of signals generated:
-
Product
Secondary Ion Mass Spectrometry (SIMS Analysis)
-
Rocky Mountain Laboratories, Inc.
Secondary ion mass spectroscopy is operated either in the dynamic mode (DSIMS) or the static mode (SSIMS). DSIMS is useful for profiling impurity and trace elements through films and interfaces. SSIMS is useful for characterizing polymeric materials and only measures the outermost molecular layer of a specimen.
-
Product
Digital Imaging
-
No one camera does it all. ACCU-SCOPE offers a wide selection of cameras for a variety of applications, and our experts can help you find the best match for your specific need. We have solutions from brilliant brightfield to low-light fluorescence, and from imaging living, moving specimens to fixed stained sections on slides. Need help deciding? Just ask!





























