-
Product
PXIe-4331, 102.4 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module
781345-01
Strain/Bridge Input Module
102.4 kS/s, 24-Bit, 8-Channel PXI Strain/Bridge Input Module—The PXIe‑4331 is a high-speed input module that provides integrated data acquisition and signal conditioning for dynamic strain, load, and pressure measurements. This module includes increased accuracy, high data throughput, and synchronization features, making it ideal for high-density measurement systems. To remove noise, the PXIe‑4331 offers antialiasing and digital filters per channel. Each channel also features an independent, programmable excitation voltage. Additionally, the PXIe‑4331 provides remote sensing, internal bridge completion, and shunt calibration options per channel.
-
Product
Wireless Strain Gauge Transmitter
-
The Wireless Strain Gauge Transmitter (WSG) series is capable of turning any manufacturers strain gauge based sensors into wireless systems which can be read using our standard range of displays, readouts and software.
-
Product
4 Channels, Strain Gauge Measurement
SG1
-
Module SG1 is NAI’s latest generation Strain Gage Measurement Module. This intelligent, four-channel module is used on our Multifunction Embedded I/O Boards and Single Board Computers (SBCs).
-
Product
4-channel Strain Gauge Amplifier Module
SCS-824
-
The SCS-824(5)(6)(7) provides 4 channels of strain gauge inputs for the SCS-800 signal conditioning system. It accommodates most strain-gauge types, from single-element quarter bridges to 4-element full bridges. Using included SystemView software, you can adjust excitation voltage, input gain, offset nulling, and all other key functions
-
Product
High Temperature, Low Strain, Extended Performance Capacitive Extensometers
Model 7650A
-
Jinan Testing Equipment IE Corporation
Model 7650A extensometers measure strains with extremely high precision due to their design features and low strain range. All models are capable of tension and compression strain measurement, and may be used for fatigue testing under fully reversed load and strain conditions at frequencies up to 10 Hz.All 7650A models mount rigidly on the load frame and incorporate slide mounting to bring the extensometer into contact with the specimen. The gauge length is set automatically before mounting on the test specimen, which allows for hot mounting after thermal equilibrium has been reached.These units are specifically designed to provide high accuracy, high resolution measurements and perform high temperature fatigue testing at the highest possible frequencies. They incorporate capacitive sensors for low operating force and include electronics with programmable filtering and multi-point linearization for improved performance and accuracy. The overall design minimizes, and in many cases virtually eliminates, any influence from common lab environment vibrations.These water-cooled extensometers are equipped with high purity alumina rods for specimen contact when testing to 1200℃ (2200°F). Silicon carbide rods are used for the 1600℃ (2900°F) high temperature option.The Model 7650A is often customized for specific test needs. Contact Epsilon for a configuration that matches your requirement.
-
Product
NI-9237, 50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module
780264-02
Strain/Bridge Input Module
50 kS/s/channel, Bridge Analog Input, 4-Channel C Series Strain/Bridge Input Module - The NI‑9237 includes all the signal conditioning required to power and measure up to four bridge-based sensors simultaneously. The module provides strain or load measurements with zero interchannel phase delay. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. You can program the NI‑9237 for use with half-bridge and full-bridge sensors with built-in excitation. The four RJ50 jacks provide direct connectivity to most torque or load cells and offer custom cable solutions with minimal tools.
-
Product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
-
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
Product
Dial Strain Gauge
DRK8093
-
Shandong Drick Instruments Co., Ltd.
This stress (birefringence) sources are due to uneven cooling or external causes such as mechanical action, which directly affect the optical glass, glass products, quality transparent plastic products. Therefore, stress control is optical glass, glass products, plastic products, such as transparency in the production process extremely important part. The strain gauge can be qualitatively or quantitatively by observing stress to identify products (DUT) quality, are widely used in optical glass, glass, transparent plastics industry for fast, a lot of testing. In fact, it can not be solved by math the complex problems.
-
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 1.5k
40-265-404
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 1.5kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 1K
40-265-202
Strain Gauge Simulator
The 40-265 is a strain gauge simulator that simulates the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. It provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
8-Channel VME Strain Gauge/Weighing Module
V380
-
The V380 is a VME/VXI compatible eight-channel strain-gauge signal conditioner which is optimized for load-cell weighing applications. The module includes tare (zero reference), DSP-based high-order filtering, averaging, triggered weighing, and other functions not commonly available in conventional strain-gauge signal conditioners.
-
Product
PCI Strain Gauge Simulator Card, 2-Channel, 2k
50-265-302
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Fast USB Strain Module
FSU-SSB
-
The FSU-SSB is a fast, compact, high precision strain bridge input module delivering high resolution readings over USB and communicated directly to a PC. It is aimed at dynamic applications that require high speed measurement.It delivers high speed measurements of 4800 samples per second at 13 bits noise free resolutio
-
Product
PCI Strain Gauge Simulator Card, 4-Channel, 350 Ohm
50-265-014
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits
310113002
Instrument Bracket
Instrument Bracket Kit, w/ Strain Relief, Slide Configuration, for 28"+ Slide Kits Similar to instrument bracket p/n 310113453, but includes cutout to accommodate air intake on NI PXIe-1088 chassis. Only compatible with slide configurations 28" and longer. Not compatible with cable tray. Not recommended for use with 2+ tier 90 Series systems (905, 9075, etc.).Used to mount testing instrument to slides and also allows test instrument to slide out for maintenance access. Provides strain relief in front area of bracket. Compatible with chassis (see drawing for more information)
-
Product
PXI Strain Gauge Simulator Module 6-Channel, 350
40-265-016
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 6-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Digital Small Strain Gauge
ZET 7110-DS
-
ZET 7110-DS digital small strain gauge (with integrated strain gauge) is also used for stress-strain state control of concrete structures, it is used within the scope of engineering structures monitoring systems (both stationary and mobile). Digital small strain gauge is used for stress-strain state control and alarm notification in the case of elastic range of stress value exceeding. ZET 7110-DS digital small strain gauge is supplied in air-tight shock-proof package with dust and moisture protection.
-
Product
FEA and Strain Gauge Testing
-
Circuit Check began Strain Gauge Testing in 1999 when BGA/SMT technology started replacing PTH components, reducing strain levels was a reactive post fixture fabrication process. We quickly recognized that the “reactionary” process was neither efficient nor were we capable on knowing the lowest achievable strain levels. Our engineering team came up with visual tools utilized during design to easily identify areas of excessive probe force, though still not enough data was generated to identify the lowest possible strain. Finite Element Analysis software models the PCBA and test fixture and applies the pressures from test probes and board supports and indicates the micro strain level applied to the PCBA. Using the FEA software during our design process allows our engineers to modify fixture designs to attain the lowest possible micro strain before fabrication begins.
-
Product
4 2/3 Strain Gage Meter (1/32 DIN)
CS3-SG
-
CS3-SG Strain Gauge Indicator has been designed with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV as like as Load Cell or Strain Gauge.The meter supports Field Calibration function. It can be calibrated with sensor(Load Cell/Strain Gauge) to meet machinery structure.They are also building in 2 Relay outputs, 1 External Control Input, 1 Analogue output or 1 RS485(Modbus RTU Mode) interface with versatile functions such as control, alarm, re-transmission or communication for a wide range of machinery and testing equipments applications.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 1k
40-265-204
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 350Ω) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Strain Gauge Sensor
ZET 7010
-
Digital strain gauge ZET 7010 is designed for measuring relative deformation using primary transducers based on strain sensors. This can be strain-gauge transducers, torque sensors or separate strain-gauge transducers connected via bridge or half-bridge circuit.
-
Product
4-Channel Strain Gage Amplifier Module for the SCS-800 Signal Conditioning System
SCS-824 Series
-
The SCS-824 series provides 4 channels of strain gageinputs for the SCS-800 signal conditioning system. TheSCS-824 series interfaces all strain gage types, fromsingle-element quarter bridges to 4-element full bridges
-
-
Product
sbRIO-9235, Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module
781579-01
Strain/Bridge Input Module
Non-Enclosed, 10 kS/s/channel, 120 Ω Quarter-Bridge Strain Gage, 8-Channel C Series Strain/Bridge Input Module - The sbRIO‑9235 measures dynamic strain on all channels simultaneously, allowing for synchronized, high-speed measurements. This capability is important for applications, such as impact tests, that require comparison across many channels at a particular instant in time. The sbRIO‑9235 includes built-in voltage excitation for quarter-bridge sensors. It also has 60 VDC isolation and 1,000 Vrms transient isolation, providing high‑common‑mode noise rejection and increased safety. Non-enclosed modules are designed for OEM applications.
-
Product
Enclosure, G12, Front Mount, 4 Cable Clamps, 6"x 18" x 12"
410114014
Enclosure
Enclosure, G12, Front Mount, 4 Cable Clamps, 6"x 18" x 12"Includes 4 cable clamps on the back end that eliminate the need for strain relief. When in open position- cable clamps permit removal of the stiffener bar so that installation or removal of cables may be performed without unplugging patchcords from the assembly. Housing: Material = .06" Aluminum, Finish = Powder Coat BlackCover(s)/Access Panel(s): Material = .12" Aluminum, Finish = Black Anodize
-
Product
Long Travel Extensometer
XL
-
The Instron model XL (long travel) extensometer is a precise device for measuring strain in highly extensible materials such as elastomers, semi-rigid plastics and films. Designed for use with electromechanical testing instruments, Instron XL units can be used to measure specimens elongation's up to 10 in or 250 mm. An optional of 15 in or 375 mm travel is also available.
-
Product
Miniature S-Beam Load Cell
500 Series
-
The Miniature S-Beam Load Cell is a bi-directional Aluminium strain gage based transducer with high performance and builtin temperature compensation. This design provides better than ±0.1% (full scale) non-linearity and includes overload protection in both tension and compression directions. Options include IEEE1451.4 TEDS capability.
-
Product
PCB Adapters - VTAC
-
VTAC comes in a right angle PCB configuration which is ideal for a variety of applications that require a PCB solution. Modular and compact, VTAC right angle inserts can be used with strain relief plates to relieve PCBs and to secure COTS connectors in place.
-
Product
Custom & Special Models
-
Futek Advanced Sensor Technology, Inc.
Custom Load Cells manufactured in the US by FUTEK Advanced Sensor Technology (FUTEK), a leading manufacturer producing a huge selection of Custom Force Sensors and Custom Torque Sensors utilizing one of the most advanced technologies in the Sensor Industry: Metal foil strain gauge technology.
