-
Product
PCI Strain Gauge Simulator Card, 6-Channel, 2k
50-265-306
Strain Gauge Simulator
These cards simulates the operation of a range of strain gauges making them ideal for testing strain gauge meters and a wide variety of industrial control systems. They provide a simple way of replacing in house developed sensors with a low cost simulator having excellent performance that is easy to calibrate and use.
-
Product
Digital Strain Gauge Sensor
ZET 7110
-
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
Product
9-Pin D-Type Female Connector
92-960-009-F
D-Sub Female Connector
This connector is designed to allow users to directly terminate cables with soldered connections. Users should make their own cable strain relief arrangements and ensure appropriate electrical safety precautions are observed when using this product.
-
Product
PXI Strain Gauge Simulator Module 2-Channel, 3k
40-265-102
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 2-channel, 3kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
IEC60065 Socket Torque Balance Tester Torsion Tester
-
Shenzhen Chuangxin Instruments Co., Ltd.
*Plug and Socket Torque Tester/Device is for compliance is checked by engaging the device, as during intended use, with the socket-outlet of a test apparatus. *Plug Torque Tester/Equipment is a device provided with pins intended to be introduced into fixed socket-outlets shall not impose undue strain on these socket-outlets.The balancing arm of the test apparatus pivots about a horizontal axis through the centre lines of the contact tubes of the socket-outlet at a distance of 8 mm behind the engagement face of the socket-outlet.*With the machine not in engagement, the balancing arm is in equilibrium, the engagement face of the socket-outlet being in the vertical position.After the device has been engaged, the torque to be applied to the socket-outlet to maintain its engagement face in the vertical plane is determined by the position o a weight on the balancing arm.
-
Product
S-Type Load Cells
-
S-Type load cells are low-cost and high performance side mounted load cells suitable for a number of weighing and general force measurement applications. They come with a 6-foot strain relieved integral cable with pigtail leads that are stripped and tinned for electrical interface.
-
Product
Propeller and Rotor Blade Strain Measurement Systems
-
Advanced Telemetrics International
ATi Telemetry Systems are typically used to transmit data from rotating shafts or machinery to a stationary telemetry receiver. The 2040BC Miniature Strain Gage Transmitter can be connected to strain gauges adhered to propellers or rotors in order to transmit blade strain or shaft torque in flight.
-
Product
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle
865684-01
-
NI-9215, cDAQ-9171, and NI-9981 USB Voltage Measurement Bundle - The USB Voltage Measurement Bundle with NI-9215, cDAQ-9171, and NI-9981 includes the NI-9215 C Series Voltage Input Module and the cDAQ-9171 CompactDAQ Chassis for voltage measurements. This bundle also includes the NI-9981 Connector for strain relief and operator protection from high-voltage signals. The included NI-9215 provides noise immunity, a high common-mode voltage range, NIST-traceable calibration, differential analog inputs, and four channels.
-
Product
Suitable For Strain Gauge / Load Cell Sensors
SEM1600B -
-
Suitable For Strain Gauge / Load Cell Sensors
-
Product
Transverse (Diametral) Extensometers
Model 3575
-
Jinan Testing Equipment IE Corporation
Designed for general purpose transverse or diametral strain measurement on axially loaded specimens. This model may be used simultaneously with the model 3542 axial extensometer.
-
Product
Strain Gauge Weighing
-
In the demanding environment of the metals processing industry getting the right balance between accuracy, speed and reliability in your sensing systems can mean a great deal. ABB offers a wide range of dedicated products for weighing applications for crane, scrap, blast furnace and continuous casting.
-
Product
Cable Tray, Slide Configuration, For Strain Relief And Cable Management, For 28" And Longer
310113424
Cable Tray
Strain Relief.
-
Product
High-Definition Distributed Fiber Optic Sensing
ODiSI
-
Luna’s ODiSI system provides the world’s highest resolution distributed fiber optic sensing solution for strain and temperature measurement. Using low-profile optical fiber as sensors, the ODiSI system maps strain and temperature fields with sub-millimeter spatial resolution, providing unprecedented detail and data insight.
-
Product
Torque Systems
-
The Drive Plate Torque System uses a low power radio link to transfer digitised strain measurements from a rotating wheel hub to a stationary antenna mounted nearby. The signals are passed to a receiver where they are decoded and output as CAN bus messages and analogue outputs.
-
Product
Force Sensors
-
TE Connectivity (TE) designs and manufactures force sensors for applications that require high performance or unique packaging, including electro-mechanical flight control, test and measurement and ultra-low cost OEM load cells for medium to high volumes. Based on our proprietary piezoresistive silicon strain gage (Microfused) technology, our sensors combine durability and long-term stability in extremely low cost packages.
-
Product
Universal Accelerometers
-
Metra Mess- und Frequenztechnik in Radebeul e.K.
There are models with charge output and with IEPE compatible voltage output. The transducers of KS series have a shear type sensing element making them less susceptible to thermal transients and base strain. The accelerometers of KD series have a compression type sensing element combining rugged design, precision and low cost.
-
Product
CAN Sensoy/ Interface
Strain
-
Reach Technologies' CAN Strain Sensor Interface sources, conditions and digitizes 8 strain sensor inputs for collection via CAN. The module is ideal for conveniently adding strain data to a distributed CAN network. The CAN Strain Sensor Interface is configurable via a CANopen stack.
-
Product
Receiver, I2 Micro ICon, 168 Position, Fully Loaded With Twin Female Contacts (610 138 200)
310130101
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 168 QuadraPaddle contacts. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is fully loaded with twin female contacts, QuadraPaddle Part # 610 138 200. Accessories such as keying pin kit, protective cover, and strain relief are available.
-
Product
8-Channel VME Strain Gauge/Load Cell Module
V385
-
The V385 is a VME/VXI compatible eight-channel strain-gauge signal conditioner applicable to generic bridge-type transducer applications. The V385 adds individual remote-sensed excitation supplies to each channel, increasing its precision over the V380's single excitation supply.
-
Product
Bolt Extensometers for Proof Load Testing
Model 3565
-
Jinan Testing Equipment IE Corporation
The Model 3565 uses hard conical points to contact the bolt at the center of the head and at the bottom. It is fully adjustable for different length bolts ranging from 25 mm (1 inch) in length to 150 mm (6 inches) standard. Extension beams are available for longer bolts. The standard maximum measuring range is 1.25 mm (0.05 inches). Generally, on longer bolts this extensometer will be self-supported without requiring any centering marks or punch marks on the bolt. For shorter bolts these marks may be required. If the conical pins are sharp, marks are often not needed even on the shortest bolts.The extensometer has a zero adjustment screw to adjust the length between the contact pins. This is used to set the output voltage to zero, which corresponds to the correct starting position for the test. It also includes a breakaway lower arm. In the event a bolt should fail, the breakaway arm snaps free, helping to prevent damage to the extensometer. This is easily re-installed. In the event that bolt failures are likely during a test, it is recommended the user attach a cord around the upper part of the beam and tie the other end to the test frame to prevent the extensometer from falling. The conical point contacts included with the extensometer are made from tungsten carbide.The Model 3565 extensometers are strain gaged devices, making them compatible with any electronics designed for strain gaged transducers. Most often they are connected to a test machine controller. The signal conditioning electronics for the extensometer is typically included with the test machine controller or may often be added. In this case the extensometer is shipped with the proper connector and wiring to plug directly into the electronics. For systems lacking the required electronics, Epsilon can provide a variety of solutions, allowing the extensometer output to be connected to data acquisition boards, chart recorders or other equipment.
-
Product
Junction Boxes
-
VPG Transducers created one of the largest load cell and transducer manufacturers in the world when we brought decades of weighing and force measurement experience under one roof. By harnessing the power of our collective expertise and experience in advanced strain gage technology, we are able to continuously challenge the status quo. As trusted partners, we are committed to providing world-class solutions that meet your needs.
-
Product
20-Pin GMCT Cable, Male to Unterminated, Cut Ends, 10A, 2m
A020GMR-C-0C200
Cable Assembly
The 20-Pin GMCT cable assembly is constructed from 19/0.254 (18AWG) Tinned Copper Wire with PFA insulation. Screwlocks are provided to secure the connector to associated product. The unterminated connections are coded to match the connector pin designation. Users may need to make their own cable strain relief arrangements when using this product and should ensure appropriate electrical safety precautions are observed.
-
Product
GTR FBG nterrogator
-
GTR FBG Interrogator for strain sensing, the World’s First ASPIC based FBG interrogator module.
-
Product
Fiber Optic Sensing Instrument
Static Strain
-
Static Strain is a low cost one-channel fiber optic sensing instrument for quasi-continuous strain monitoring. With over 2,000 sensing points on a single fiber, users are able to achieve spatially continuous real-time strain monitoring.
-
Product
Strain Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Strain Measurement Module comprises of Cantilever Beam bonded with four strain gauges,pan and weights upto 1Kg. Digital 3½ digit indicator module is supplied to read the microstrain.
-
Product
Custom Bolt-On Strain Sensors
-
Our custom bolt-on strain gauge sensors are designed and manufactured to your application, based on your drawings and specifications, including all types of output formats. Ideal for dynamic load monitoring, capable of measuring and monitoring axle stress and weight with high accuracy.Do you have an application for strain gauge measurement that requires a quick and simple installation, repeatedly, in multiple locations? Perhaps you need a sensor with high environmental protection, which removes the necessity for time-consuming cleaning, complicated soldering and messy strain gauge adhesives?
-
Product
25-Pin D-Type Female Solder Bucket
92-960-025-F
D-Sub Female Connector
This accessory is designed to allow users to directly terminate a cable with soldered connections to the connector. When the product is used without a backshell users should make their own cable strain relief arrangements and ensure appropriate electrical precautions are observed.
-
Product
Receiver, I2 Micro ICon, 168 Position, For Crimp Contacts
310130102
Receiver
The i2 Micro iCon receiver is a one piece connector capable of holding up to 168 QuadraPaddle contacts. QuadraPaddle modules are molded on .100” (2.54 mm) centers to meet the need for high-density I/O in a compact assembly. This i2 receiver is made for crimp contacts. Accessories such as keying pin kits, protective covers, and strain relief are available.
-
Product
DIN Rail Mount
-
Encore Electronics offers a complete line of compact, economically priced instrumentation packaged in standard DIN rail mounted enclosures. Our products include frequency to voltage converters, strain gage amplifiers, notch filters, accelerometer conditioners, and line drivers. Overall package sizes are 3.1″ x 3.3″ x 0.9″ tall (single wide) or 1.6″ tall (double wide).
-
Product
DC Source/Calibrators
-
Our DC Source/Calibrators are designed for a typical applications such as the design, check and calibration of high speed, high resolution A/D converters; design and certification of high speed data logging and process control systems; calibration of digital voltmeters and multimeters; as an “IMBEDDED STANDARD” and/or simulator; design, testing, simulation and certification of thermocouples, strain gages and transducer instrumentation.
