-
product
Test Systems Inspection Systems
Different requirements demand flexibility. ELABO boasts a modular product portfolio permitting the economical creation of bespoke solutions for every client. These solutions range from individual testing devices through tabletop workstations with integrated testing equipment all the way to automated systems with ERP connections for mass production.
-
product
Temperature Indicator
TICT
The LogTag® TICT is a low cost disposable electronic temperature indicator for use in monitoring temperature & time statistics in transport applications of up to 45 days duration. The LogTag® TICT can monitor and record statistics against four factory pre-set temperature limits for up to 45 days, displaying ‘OK’ if environmental conditions remain within limits. If temperatures exceed two high temperature alarm limits or go below two low temperature alarm limits, the LCD shows a ‘REJECT’ alert, indicating the goods require further checking.
-
product
Force Balanced Accelerometer
PA-23, PA-23BH, S-230
The Geotech Model S-230 is a high resolution, 1-component, force balanced accelerometer capable of meeting the noise and stability requirements of the most demanding seismic studies. It features a very wide frequency response (DC to 90 Hz) and an internal calibration coil. Three S-230 accelerometers are packaged as a borehole 3-component unit (Model PA-23BH) and as a surface 3-component unit (Model PA-23). PA-23BH can be submerged up to 100 m depth.
-
product
Temperature Cycling Test Chamber
Guangdong Bell Experiment Equipment Co.,Ltd
DGBell’s Temperature Cycling test chamber is performed on materials to determine the resistance of exposure to alternating extremes of high and low temperatures.
-
product
Automated Temperature Resistance Standard
Measurements International Ltd.
Exceptional Stability, Cost-effectiveness, Performance-based Results, 10 Ω, 25 Ω, 100 Ω, 200 Ω, 400 Ω and 1000 Ω Internal Standards, Built-in Temperature Chamber for Optimal Performance.
-
product
Burn-in or Rapid Temperature Cycling Chamber
KDL Series
The Bemco KDL series is designed for production testing of electronic circuit boards and completed electronic systems. They accept Bemco KDLC Carts that have a working area of 42 wide by 60 high by 48 deep suspended on insulated runners and casters 11 inches above the test area floor.
-
product
System Module
CM AXIe-1
The module functions as a system module of the AXIe-1 standard crate.
-
product
Review System
RV-3000
Reduces surface inspection device review time and contributes to greater inspection efficiency! This system uses address information for defects detected by surface inspection equipment to acquire images of defects with a high level of magnification, and categorizes defect types.
-
product
Logger version conductivity and temperature sensor
INFINITY-CT A7CT-USB
Infinity-CT is an autonomously deployable data logger for temperature and salinity measurements. The conductivity sensor has a design of 7-electrode. The small-sized instrument (Φ54mm x 255mm, 0.7kg in air) can be deployed and integrated virtually anywhere. The instrument has two depth rating versions: shallow water (200m, A7CT2-USB) and deep water (2,000m, A7CT-USB).
-
product
Flexible Temperature Testing & Thermal Cycling
TA-5000B Series
MPI Thermal manufactures a variety of compact temperature chamber solutions for electronics and material test and thermal conditioning. An array of standard and custom design high-performance Clamshell styles and other configurations and custom dimensions and sizes are available. MPI ThermalAir Systems compact chamber thermal products are available to meet your test application needs.
-
product
System Layout
CARGOMASTER®
The parts that build up the system. Signal Control unit, the Computer Unit, Power Supply and Tank Sensors.
-
product
High Temperature Charge Mode Accelerometers
Charge mode output accelerometers from PCB® use piezo-ceramic sensing elements that output an electrostatic charge signal proportional to the applied acceleration. These sensors can operate at extremely high temperatures because they do not contain the built-in signal conditioning electronics that limit the temperature range of ICP® accelerometers. Charge mode sensors are used in the testing of gas and steam turbines, jet engines, high power motors, exhaust systems and automobile engines where temperatures can range from 500° F (260° C) to 1200° F (649° C).
-
product
Blackbody System
IR-563/301
Infrared Systems Development Corp.
IR-563 is a ideal source for the Near (1-3 um), Mid (3-8) and Far (8-30+ um) infrared bands. The IR-563 has been the industry standard 1000º C blackbody for more than 30 years, and continues to provide excellent service to infrared applications throughout the industry. The IR-564 extends the temperature range of the IR-563 to 1200º C by changing cavity materials to Silicon Carbide and high purity Alumina ceramics, otherwise the two units are virtually identical.
-
product
Digital Temperature Transmitter
Model T15.H
Digital temperature transmitter Model T15.H - Applications: Process industry, Machine building and plant construction
-
product
Smart Temperature Split Kit
HUB2
UEi Test & Measurement Instruments
The HUB2 gives the ability to wirelessly get temperature and relative humidity via the WHP1 probes and free UEi Hub App. Easy to use and a rugged design make the App and probes an excellent addition to any technician's toolbox.
-
product
VIP IFEC & CMS Systems
Astronics is the smart choice for inflight connectivity, entertainment, and cabin management solutions for VIP, VVIP, and business aircraft. From the highest-performing global SATCOM connectivity for optimum productivity and entertainment, to our Avenir IFE/CMS line that incorporates the latest technologies to deliver native 4K video distribution through the highest bandwidth Ethernet network system in the industry, Astronics is ready with a cutting-edge solution that delivers the ultimate VIP experience.
-
product
Cost-Effective ATE System
PRO RACK ATE
Qmax Test Technologies Pvt. Ltd.
Pro-Rack is a cost effective ATE System, which comes with Modular Structure provision option to improvise and enhance much instrumentation based on the user’s requirements. Basically it is designed to cater to the needs of PCB test and repair depots, keeping in mind the changing PCB technology and the challenges in testing them off-line. It can provide complete PCB test and diagnostic functions for any kind of PCB including the latest very high density complex PCBs with high pin count PQFP, FPGA VLSI chips. AC /DC parametric tests enables testing of the DC parametric of device pins on the edge connector for input bias current, Fan out capacity ,Tri-state leakage currents, AC parametric measurements such as Input / Output Propagation delay Rise time / Fall time to further enhance fault coverage. Pro-Rack is designed with VPC Mass Interconnect adapter with 16 bit fixture ID interface to the UUT through simple clips and probes or through card edge or through a bed of nail test fixture.
-
product
Temperature Data Loggers
The Track-It™ Temperature Data Logger is a battery powered stand alone compact data logger that records up to 64,000 samples of temperature data. The unit is easily configured using the included Track-It™ Software. Simply plug the logger into an open USB port on your PC and the software automatically identifies the logger. Configure the unit to start and stop recording at a predetermined time and date or only when an alarm condition is sensed. The sample storage rate can be set from 1 sample every 2 seconds to 1 sample every 24 hours.
-
product
Laser Systems
Laser systems (laser range finders, laser designators, laser receivers, laser trackers, laser pointers) are one of crucial technologies for defense/security sector. Laser systems have also found mass applications outside defense sector. Testing laser systems is needed for both manufacturers, maintenance workshops and final users for a set of different and important reasons. Hi-tech test equipment can help significantly in manufacturing, maintenance, training, purchase optimization, and optimal use of night vision devices.
-
-
product
Development System
FE-900
# Emulates Philips P89LPC932 Microcontrollers# Real-Time and Transparent Emulation up to 12MHz# 8K Emulation Memory# Real-Time Trace# Uses Philips Bond-Out Technology# Ceibo Windows Debugger and Keil uVision2# High-Level Support for all C/C++ Compilers and Assemblers# On-Line Assembler and Disassembler# Target Board, ISP Programmer and Power Supply Included# PLCC-28 Emulator Plug Included (TSSOP-28 Optional)
-
product
Force Tensiometer
K20
Our Force Tensiometer – K20 is a robust, semi-automatic instrument for the precise measurement of surface tension and interfacial tension. Using the ring and plate method as the main tensiometric methods, it produces reliable measurements for the routine quality assurance of your surfactant solutions and interfacial processes.
-
product
Test Systems
In-Circuit Test (ICT) tests populated circuit boards by means of electronic measurements through thin needles on test fixtures. We offer in-circuit testers for various testing strategies – from the flexible 19“ rack to the ergonomic high-performance tester. And all of our in-circuit testers are also available in the Lambda edition for true parallel testing. The flying probe test checks your printed circuit boards using four movable test heads. This requires no fixtures and allows for flexible test program generation. That makes our flying probe test systems ideal for a high mix of printed circuit boards and small to medium test volumes, such as for prototype testing.
-
product
Configurable Temperature Transmitter – Wall Mounting
HD786TR1
Configurable temperature transmitter with output 4...20 mA. Measuring range -200…+650°C, minimum range 25 °C.
-
product
Digital Force Gauge
Guangzhou Amittari Instruments Co.Ltd
The digital force gauge is a kind of simple and convenient multi-functional instrument for high-accuracy push force and pull force test. It is widely used in electronics, building hardware, textile, auto parts, ignition device such as lighter, fire fighting equipment, pen manufacturing, lock manufacturing, fishing gear, chemical, power machinery, scientific research institutions and other industries. For the push and pull load test, plug and unplug force test and destructive test etc.
-
product
Inspection System
Pixie
3-D Metrology for automation. Pixie is a standard system for automated optical quality inspection. Pixie can be configured with 2 to 5 servo driven axis movement and the high-speed measurement capabilities make it suitable for inline and stand-alone solutions.
-
product
Temperature and Humidity Regulator
H3331-2
Relative humidity, temperature probe on a cable. Measured values are also converted to other humidity interpretation: dew point temperature, absolute humidity, specific humidity, mixing ratio, specific enthalpy. Three two-state inputs.
-
product
GPS Systems
High accuracy 100Hz GPS with Real-time Kinematics (RTK) correction for the most precise position-based test and measurement applications.
-
product
Temperature & Humidity Chamber
SG-H01T
This tester is used to determine the character change and the extent of strength deterioration of the shoe materials and sole under the high temperature and high humidity. It's also used to assess the discorloration and shrinkage of the leather productors under the simulate environment in container. It's specially used in testing the character of heat-endurance, cold-endurancer, drought-endurance and wet-endurance for various materials
-
product
Temperature, Humidity And Others Relevant Environment Tester
King Design Industrial Co., Ltd.
Allows your product quality and reliability tests more realistic toward actual environment; simulate the actual environment in the temperature, humidity and vibration by separated of combined tests. The tester is equipped with control panel, Chinese-English display and micro-computer temperature control system; applicable to aerospace, military, vehicles, electronics and other high-tech products.
