Thermal Chamber
See Also: Temperature Forcing Systems, Thermal Shock Chambers
-
Product
Thermal Shock Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Three zone thermal shock chamber uses the test material structure or composite material to withstand the degree of extreme high temperature and low temperature in a continuous environment in an instant, so as to test the chemical changes or physical damage caused by thermal expansion and contraction in the shortest time.
-
Product
Thermal Shock Chamber
ETS-Series
-
air-to-air and liquid-to-liquid Thermal Shock Chambers from Envisys are available in different volumes to suit the varied testing needs. Horizontal or vertical models consisting of cold and hot zones with product carrier basket of sizes 50, 100, 150, 300, 600 and 900 litres which transfers the specimen under test between cold and hot zones using electro pneumatic / motorized basket movement.
-
Product
Thermal Shock Chamber
ATS Series
-
Thermotron thermal shock chambers meet a variety of testing needs and come in three configurations: vertical, horizontal, and double duty. A product transfer mechanism automatically transfers products under test from hot to cold zones and back when programmed in the controller.
-
Product
Thermal Shock Chamber
-
The Thermal Shock Chamber is specially designedwith independant temperature zones to facilitatethe automatic transfer of product under testthereby simulating a temperature shock to test the reliability of the product as per military and other international standards.
-
Product
Liquid Thermal Shock Baths
TSB Series
-
CSZ's Liquid thermal shock chambers consist of separately controlled hot and cold baths. Product is submersed in fluid and thermally stressed between the hot and cold baths, resulting in immediate product temperature changes. CSZ uses perfluorinated fluid that does not coat the product or conduct electricity for use in both the hot and cold baths to eliminate cross contamination and reduce evaporation losses.
-
-
Product
Climate Control Test Chamber
-
ACMAS's Climate Test Chamber is ideally suited for specimen test requiring quick changes of temperature. It covers various applications from JEDEC and IEC test standards. ACMAS Thermal Cyclic Chamber is equipped with advanced technology such as specimen temperature control which allows linear specimen temperature rates of change during rapid thermal cycling or accurate temperature ramp control. This chamber is also known as Climatic Test Chamber and Climate Controlled Test Chamber.
-
Product
Software
BatteryPro
-
Chroma Systems Solutions, Inc.
The software is item driven with built-in tests – meaning no programming is required at all. Users are able to read data from the BMS controller and also includes thermal chamber control. Battery Pro Software supports Chroma’s regenerative battery cyclers and provides a safe and stable testing environment.
-
Product
Flexible Temperature Testing & Thermal Cycling
TA-5000B Series
-
MPI Thermal manufactures a variety of compact temperature chamber solutions for electronics and material test and thermal conditioning. An array of standard and custom design high-performance Clamshell styles and other configurations and custom dimensions and sizes are available. MPI ThermalAir Systems compact chamber thermal products are available to meet your test application needs.
-
Product
Low Outgassing Cables Suitable For Thermal Vacuum Chamber Exposure
-
Low Outgassing Cables Suitable for Thermal Vacuum Chamber Exposure.
-
Product
2-Zone and 3-Zone Vertical Thermal Shock Chambers
FS
-
Originally developed for testing microelectronic devices for use in military and aerospace electronic systems, Bemco Vertical Thermal Shock Chambers are widely used for screening and quality evaluation of smaller electronic parts.
-
Product
Thermal Shock Chamber
-
Allows for the rapid transfer of products between temperature extremes, or the alternating heating and cooling of test articles in cyclical manner.
-
Product
Thermal Shock Chambers
VTS-Series
-
Vertical Thermal Shock chambers consist of two separately controlled hot and cold zones. Product is transferred between these zones for rapid product temperature changes. Thermal Shock Chambers are designed to perform tailored environmental stress screening of component and board level electronic assemblies. The return on investment in both actual savings and customer confidence adds greatly to the value of electronic assemblies screened in a CSZ thermal shock system.
-
Product
Thermal Shock Test Chambers
-
How well does your product stand up to the shock of extreme thermal temperature changes? Tenney Environmental's thermal shock test chambers take products from 200°C to -65°C in just seconds.
-
Product
Pyroelectric and Thermal Testing
-
The optional Chamber Task measures the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled within a thermal chamber, on a hot chuck or in a furnace. From these measurements the Spontaneous Polarization Pr(q) and the Dielectric Constant er(q) are computed. These are then combined to determine the Electrical Displacement D(q) as a function of the temperature q.
-
Product
Material Test/Cure Rooms
-
Our walk-in Materials Test and Cure Rooms offer reliable, efficient environmental controls for a variety of applications including shelf-life testing and storage, ceramic and concrete wet and dry cure regimens (including ASTM-compliant units), thermal shock chambers, general, medical and packaging materials.
-
Product
Thermal Shock Chamber
-
Wewon Environmental Chambers Co, Ltd.
Makes it possible to quickly and autonomously transfer test items back and forth repeatedly between a hot and cold environment.
-
Product
Test House Services
-
At TS-Space Systems we have over 30 years experience in designing, building and operating vacuum systems for space simulation and materials testing. We have three in-house thermal vacuum chambers which are configurable for a range of temperatures for either monitored vacuum bakeout or thermal vacuum cycling. We design, build and operate these systems in-house which means we are more flexible than most test houses and are happy to modify feedthroughs, manufacture additional support equipment and even change the operation of the chambers, where possible, in order to accomodate customer requirements.
-
Product
Integrated Test Facility
ITF
-
The ITF, located in El Segundo, California, has multiple test stations to enable parallel testing and significantly streamline program test schedules. More than 25,000 square feet are available for integration and test activities, including a 10,000-square-foot Class 10K clean room. Our facilities feature thermal vacuum chambers and test stations to support optical alignment, warm optical bench testing, and hardware integration.
-
Product
Thermal Shock Chambers
-
We provide a large selection of thermal shock chambers to accommodate various types of product testing. Thermal Shock Chambers perform tailored environmental stress screening of component and board electronic assemblies. Our unique chamber design transfers product between two extreme temperature-controlled chambers, passing equal volumes of high velocity conditioned air over the product and resulting in rapid product temperature changes. The induced thermal stresses can reveal hidden manufacturing defects in electronic sub-assemblies and other components by the expansion and contraction of critical parts.
-
Product
Environmental Test Chamber
-
High and Low Temperature Test Chambers, ESS Environment Stress Screening, 2 Zone Thermal Shock Test Chamber, 3 Zone Thermal Shock Chambers, Walk-In Chambers, Burn-in Room and Aging Test Chambers, Altitude Chambers, Industrial Drying Oven, Salt Spray Test Chambers, Temperature Humidity Vibration Comprehensive Test Chamber, Test Machine Series, Custom Made Environmental Test Equipment, Double-Layer High and Low Temperature Chamber, Explosion Proof Temperature Chamber For Power Battery, etc.
-
Product
Temp Characterized CalPod, 20 GHz
85531B
-
CalPods provide a new and unique way to quickly and easily refresh a network analyzer calibration, at the push of a button and without removing the DUT or re-connecting standards. Very useful in thermal chamber testing, where it is desired to remove the thermal effects of the test cables and connectors from the DUT’s response, and where it is impractical to stop the thermal testing to perform a normal re-calibration.
-
Product
Space Simulators
A6H Series
-
Bemco offers up-to-date space simulators incorporating all of the preferred features needed for reliable combined temperature and high vacuum testing. The A6H series includes a fully integrated and appropriately sized PCL-III Portable Liquid Chiller utilizing liquid nitrogen for cooling. The PCL-III is mounted within the A6H system structure and permanently attached to the chamber thermal shroud. Mechanical cooling is available as an option.
-
Product
Thermal Shock Chambers
-
Shanghai Morningtest Environmental Chambers Co.,Ltd.
Thermal Shock Chambers are designed for the safe, efficient, and accurate environmental testing of electronics and consumer products, and aerospace, telecommunications, and military and defense components.
-
Product
Chamber/Pyroelectric Task
-
Radiant's Chamber/Pyroelectric Task sets the sample to a series of temperatures by performingGPIB control of an external thermal device. At each temperature it captures the sample’s polarization response and/or small-signalcapacitance. These are combined to calculate the pyroelectric coefficient. The Pyroelectric Task is to be used with a Radiant Test System and a Linkam Stage (-196C to 600C), Thermal Chambers, Hot Chucks, or a Furnace to automatically measure the Pulse Polarization response and Small Signal Capacitance of a Pyroelectric material that is being heated and/or cooled. Radiant's Pyroelectric measurement Task can be added to Vision at additional cost. This measurement suite fully characterizes the pyroelectric charge (polarization) response of the sample under test. The Pyroelectric Task suite controls various thermal controllers such as Quantum Design, Lake Shore, Delta Design, and many others. Detailed Listing of Thermal Controllers Registered in Vision. The Chamber/Pyroelectric Task is quoted upon request.
-
Product
Thermal Shock Chambers
-
Weiss Technik Thermal Shock chambers are designed to give quick transitions between a HOT and COLD temperature zones. Available in vertical, horizontal and liquid models. Thermal stock chambers are used in all industries including Automotive, Electronics, Aerospace, and others to help find product defects in electronic components and product assemblies. Thermal shock is important with MIL -STD 883 test standard.
-
Product
Compact Temperature Chamber
FB1.5V-UHC Series
-
Based on the proven Bemco FB1.5V Compact Temperature Chamber, the FB1.5V-UHC offers spectacular temperature change rates in excess of 75 C per minute. With an extremely compact footprint these chambers cost about 1/3 of the amount of a typical 2-zone thermal shock chamber such as a Bemco FS2V.
-
Product
TSE-12-A Thermal Shock Chamber
-
Did you think that getting a thermal shock chamber was too expensive, required special utilities, and half your lab-space? The TSE-12 thermal shock chamber is the solution. Only 26 inches wide, the TSE-12 transfers product loads between cold and hot zones with a temperature range of -65°C to 200°C.
-
Product
Climate Chamber
ICH
-
Its excellent temperature and humidity homogeneity positions the climate chamber ICH in the international top league of stability test chambers. Thermal transfer to the interior whether heat or cold is guaranteed through a large-area air jacket on four sides. Thanks to its hermetically sealed interior, the climate chamber ICH does not consume any water once the setpoints have been reached, provided that the door is not opened. Two high-grade platinum temperature sensors with mutual monitoring guarantee interruption-free long-term operation even if one sensor should fail.
-
Product
Thermal Shock Test Chamber (2 Zone)
-
Guangdong Test EQ Equipment co., Ltd.
- Thermal Shock Chamber: -70℃~150℃, ≤5min recovery, meets MIL-STD-810. Ideal for PCB/IC reliability testing.- ESS Environmental Chamber: Humidity 20%~98% RH, supports GB/T 2423 standards. 40% energy saving vs. competitors.- Liquid-to-Liquid Shock Tester: LN₂ cooling to -196℃, 15s transition time. For aerospace materials validation.- Thermal Cycling Equipment: 25℃/min ramp rate, 1000L capacity. JESD22-A104 compliant.- Benchtop Thermal Chamber: -65℃~150℃, 65dB low noise. Lab-use with USB data export.
