-
Product
Temperature Sensors
-
A temperature sensor is a device that detects and measures hotness and coolness and converts it into an electrical signal. At TE Connectivity (TE), we design and manufacture a broad portfolio of temperature sensors – including our NTC thermistors, RTDs, thermocouples, and thermopiles – designed for efficiency and easy installation, with capacity to reliably integrate technology that responds to human behavior.
-
Product
Tensile Compression Force Tester
ESM303
-
The ESM303 is a highly configurable single-column force tester for tension and compression measurement applications up to 300 lbF [1.5 kN], with a rugged design suitable for laboratory and production environments. Sample setup and fine positioning are a breeze with available FollowMeTM force-based positioning - using your hand as your guide, push and pull on the force gauge or load cell to move the crosshead at a variable rate of speed.
-
Product
Temperature Measurement IR Sensors & Detectors
ST120 TO-5
-
A single-channel silicon-based thermopile provides lowest cost solutions in a small active area of 1.2mm x 1.2mm in a TO-5 package. Time constant of 25ms with Nitrogen encapsulation gas. Delivers a very low Temperature Coefficient of Responsivity of -0.04%/C. This detector has a very short thermal shock response to ambient temperature change.
-
Product
High and Low Temperature Humidity Chamber
GDJS/GDJW
-
•The chamber is produced by SUS304 Steel, the temperature keeping material is produced by Polyurethane hard foam and ultra-fine fibre glass, the doorframe heat insulated by Double high temperature aging silicone rubber door sealing strip. •The temperature controller is used by Korean TEMI display in English/Chinese and German Siemens PLC, it can be communicated to PC via RS-232. The temperature accuracy is 0.1℃ and humidity is 0.1%R.H •The temperature sensor is platinum PT100 Ohms/MV resistor •The heating system is full separately system which produced by Nickel chromium alloy electric heating type heater •The cold system is applied by fully enclosed fan cooled single-stage and cascade refrigeration mode, the compressor is from France TECUMSEH brand which can allow you get after sales support from many countries •The cyclical system is applied by High temperature low noise air conditioning type motor and Multi blade centrifugal wind wheel •The safety self-protection function include Electric leakage, short circuit, over temperature, motor overheating, compressor pressure, overload, over-current protection •Working Power: AC380V±10% 3phases and frequency 50Hz/60Hz •Working Environmental: Temperature is 5℃～+30℃ Humidity ≤85%R.H
-
Product
Mini Temperature and Humidity Meter
PTHM15
-
Auto Power OffFast Response TimeDew Point TemperatureDual Display Temperature & HumidityData Hold FunctionHumidity Range: 0-100%RHTemperature Range: -20 - 80 C / -4 - 176 FDew Point Temperature: -20 - 80 C / -4 - 176 FWet Bulb Temperature: 0- 80 C / 32 - 176 FHumidity Accuracy: +/- 3% RHAir Temperature Accuracy: +/- 0.5 C @ 25 CResolution: 0.01% RH, 0.01 C/FResponse Time: %RH: 105 (90% at +25C still air)Battery Type: 9V (Included)Operating Temperature: 32 F to 104 F, <80% RHStorage Temperature: 14F to 140 F, <80% RHDimensions: 6.89' H x 2.28' W x 1.38' DWeight: 5.04 oz.Sold as : Unit
-
Product
Digital Temperature Sensors
-
Analog Devices offers a broad selection of digital temperature sensors with I2C, SPI, and mark space interfaces. For more intricate system design applications, some of these sensors have integrated D/A converters, A/D converters, references, and limit alarm register. All of these sensors possess a broad range of uses, including scientific, medical, and aerospace applications, in test and measurement equipment, and in industrial automation.
-
Product
Temperature Logger
TRIX-16
-
The LogTag® TRIX-16 is a versatile, wide range, multi-trip Temperature Logger, featuring high resolution temperature readings over a measurement range of -40°C to +85°C (-40°F to +185°F). Enclosed in a robust and durable polycarbonate case, the TRIX-16 features a real time clock, which provides date/time stamps for each temperature reading.
-
Product
Collaboration Systems
-
Solutions for small meeting, huddle, or collaboration spaces that foster group sharing using technology.
-
Product
Test System
DA-2 ATS
-
The DA-2 ATS is an economical Commercial-Off-The Shelf (COTS) build-to-print tester. The test station is compliant with the published drawing package. The system does not include software.
-
Product
Control System
CONTROLSTIK II™
-
The Myron L® CONTROLSTIK II™ Rinse Tank System dramatically reduces the amount of water used in continuous flow rinse tanks. At the same time, it automatically maintains optimum water purity, ensuring effective rinsing.
-
Product
Power Temperature Cycling
-
Typically, this test would be selected when during its normal operating activity, the device is subjected to high temperature excursions and is required to power on and off at all temperatures. The power and temperature cycling test will determine the ability of a device to withstand exposure to such temperature extremes with operating biases periodically applied and removed. The worst case conditions expected in a typical; application will be simulated.
-
Product
Field-Mount Temperature Transmitters
-
The compact and robust field mounted temperature transmitters of this established and proven series from ABB are accommodated in field housings with optional indicators (TTF300 and TTF300-W: LCD display including device configurability).The field housings of the transmitter are either made of aluminum die cast or of stainless steel. The type labels are available in stainless steel. The devices are deliverable with a tube mounting kit or a wall mounting kit.
-
-
Product
Temperature Humidity Test Chamber
-
Sanwood Environmental Chambers Co ., Ltd.
Battery high low temperature test chamber is designed to test all types of batteries, including lithium-ion batteries. The battery test chamber has many safety functions built into the test chamber, which can handle battery tests and prevent safety accidents. Charge/discharge cycle testing, which determines the number of times a battery can be used by evaluating it until it deteriorates after repeated cycles of charging and discharging. In the laboratories involved in battery testing, tests based on charge and discharge cycles are a key activity. The instruments used for this type of test usually perform harsh and lengthy test protocols on the battery and can usually be connected to various instruments.
-
Product
Automatic System
-
By combining with Hardness Tester, stage control is automated in indent/multi-pointmeasurement to reduce the dispersion caused by each operator. This system is very effective for large-scale rationalization and energy saving.
-
Product
Multipoint Temperature Sensor
TSM800
-
The TSM800 multipoint temperature sensor is ideally suited for measurement of process temperatures over multiple locations with a single access point.Typically used in process plant vessels the TSM800 provides a cost effective alternative to mounting multiple individual sensors and their associated process vessel entries.
-
Product
CATV Systems
-
Sumitomo Electric Industries, Ltd.
We provide CATV solution that flexibly meet the needs of CATV operators.
-
Product
Lithography System
JetStep S3500
-
The JetStep S3500 panel lithography system is designed specifically for advanced packaging panel production. The system incorporates advanced features that address requirements for panel-level packaging, such as die shift due to placement accuracy or subsequent processing steps, CTE mismatch, panel warpage and panel handling.
-
Product
Wireless Temperature Monitor
VAT820-CO2 / VAT820-CO2-VOC99
-
Shanghai Yi Hua V&A Instrument Co., Ltd. CO.,LTD
Indoor air quality monitor :CO2 monitor , indoor air quality including CO2,VOC temperature ,humudity.
-
Product
Force Sensors, Load Cells, Shear Beam
-
INELTA Sensorsysteme GmbH & Co. KG
Exact force measurement and weight measurement
-
Product
Test System
MxDSRC™
-
The MxDSRC Test System simulates systems in the vehicle that interact with the DSRC radio module to create tests closely replicating real-world scenarios. Its integrated approach allows the DSRC components, such as RF quality and protocol conformance, to be exercised with multiple system components. MxDSRC provides a powerful and easy-to-use framework for testing your DSRC system.
-
Product
XRD System
SmartLab®
-
SmartLab includes as standard Rigaku's patented Cross Beam Optical™ (CBO) technology. CBO technology uses simultaneously mounted, simultaneously aligned optical components for both focusing (Bragg-Brentano) and parallel beam diffractometer geometries. Users can switch between the two geometries without the need to remove, replace, or realign optical components.
-
Product
Temperature Transmitter
T4311
-
Transducer is designed for temperature measurement at C or F by means of the externaltemperature probe with RTD Pt1000 sensor.
-
Product
Gauging System
Equator™ 300
-
Advanced Industrial Measurement Systems
The Equator is a flexible gauge that is designed to provide speed, repeatability and ease of use for manual or automated applications. The Equator is a highly valuable option for manufacturers who are looking to replace their current gauging method. Its system enables process control by delivering highly repeatable, thermally insensitive, versatile, and re-programmable gauging to the shop floor.
-
Product
External Temperature for PT100 Probe
TGP-4104
-
This data logger uses an external PT100 probe to record high temperatures. Probes are available to measure up to 300 and 600C. These are listed in the 'You will also need' section. The PT100 probes are of 3-wire construction and use class A elements, making them more accurate than their 2-wire predecessors.
-
Product
3-Component Quartz Force Rings And Links
-
Three-component dynamic force sensors are offered in both ICP® and charge output configurations for dynamic and quasi-static force measurement applications. Each utilizes an array of precision aligned, quartz sensing crystals. Measurements along the z-axis are proportional to applied compression, tension and impact forces. Measurements along the x and y axes are proportional to shear forces that are imposed upon preloaded crystals by the test fixture.
-
Product
Modular Breakout System 78-Pin D-type Plugin Module for 40-525A
95-525A-001
Modular Breakout System
The 95-525A-001 Plugin Breakout Module is designed to be fitted to a PXI 40-525A Signal Insertion & Monitor Matrix Module as part of the Pickering MBoS. The Modular Breakout System is designed to Simplify HILS (Hardware In the Loop Simulation) Applications.
-
Product
Sensor Products: Weld Force Gage
90061
-
Model 90061 is a self-contained, portable measurement system which allows auditing of the pinch force generated between the electrodes of resistance spot welders. Resistance welding uses a pair of electrodes to clamp two base metals firmly together prior to and during application of electrical current. Poorly clamped parts result in a defective joint. A correctly clamped assembly aids in reducing the resistance in the joint and allows the current flow to properly heat the base metals to weld the part.
-
Product
Relative Humidity & Temperature Probe
HMP7
-
Vaisala HUMICAP® Humidity and Temperature Probe HMP7 is designed for applications which involve constant high humidity or rapid changes in humidity such as drying and test chambers, combustion air and other humidifiers and meteorological measurements where measurement performance and chemical tolerance are essential.
-
Product
Configurable System For Temperature Measurement With CAN Interface
MU thermocouple1 CAN
-
The thermocouple measuring unit offers connections for 8 thermocouples, which are designed for the temperature measuring ranges J, K or T, depending on the product version.
