Bench
table top for staging and building test equipment
See Also: Test Benches, Benchtop Chambers, Bench Multimeters
-
Product
Portable Command & Control
-
Kratos Defense & Security Solutions, Inc.
Similar in functionality to the Bench Top System, the Man-Portable C2 system is used to control or monitor unmanned ground vehicles in tele-operational or autonomous modes. It is a vehicle independent system that can be used to control military or commercial vehicles that have been outfitted with our vehicle automation kit.
-
Product
Bench-Top Type Amplifiers
-
– A variety of wavelength bands– Most models have the RS232C / IEEE488.2(GP-IB) interface as default– customization is available– Development of next-generation optical communication systems– Amplification for evaluation of transmitted signals– Detection of faint signals in optical measurements & sensors
-
Product
Network Analysis
-
Network development solutions come in different formats to support the variety of applications, such as network analysis or node emulation. Network analysis is crucial throughout the development of any networked system or module. The ability to capture, view, and record messages allows monitoring of bus integrity or troubleshooting functionality of the modules on the network. Whether developing a concept or preparing for production, access to the network is essential. Node simulation can be done with software, such as ATI's CANLab Software, or hardware components, possibly CANverter, depending on whether the environment is on the bench or in the vehicle.
-
Product
Mechanical Bench-top Test Jigs
CGF Series
-
Advanced test jig, using a cam-operated, fully adjustable gate - self customisation.
-
Product
Bench top Dielectric Withstand tester
HYPOT III
-
RS-232 Interface available for automated controlPatented SmartGFI® functionPatented CAL-ALERT® functionComes complete with a test box for products terminated in a line cordPatented VERI-CHEK® functionStorage of up to 10 setups with 3 steps per setupBuilt-in security settingsDigitally controlled arc detection systemNo load setup of trip current and output voltageElectronic ramping (up & down)Built-in adjustable continuity testInterconnection to HYAMP® III to form complete test system
-
Product
AC & DC Electronic Loads
-
The Adaptive Power Systems Electronic Loads cover a wide range of power levels, voltage and current profiles and feature sets.Supported voltages range up to 1250Vdc or 350Vrms AC. From bench to system and DC or AC requirements, we can more than likely offer you the optimal programmable load to meet your needs.
-
Product
Close Link Three Phase Energy Meter Test Bench
SY8320E
-
Hong Kong Songyang Industrial Ltd.
Close-link and ordinary calibration both can be used, ordinary calibration can be used to test single/three phase active and reactive energy meter (up to 0.5 class),close-link calibration can be used to test single/three phase active and reactive energy meter (up to 1 class)
-
Product
DC Bench Power
XPL Series
-
AMETEK Programmable Power, Inc.
The Sorensen XPL series has been designed to meet the need for compact power supply at a reasonable price. The XPL series provides 30 to 125 watts of programmable linear DC power. The XPL is a compact, high performance low cost power supply suited for benchtop applications.
-
Product
Fully Automatic Close Link Single Phase Energy Meter Test bench
SY 8125
-
Hong Kong Songyang Industrial Ltd.
The devices are fully made by aluminum alloy materials and the table board is composed of fireproofing and heat-proof materials. The output voltage and current use soft startup and stop. It has the protection functions of voltage short circuit, current open circuit and power amplification exception. The device has the features of high stability, good reliability and large output power
-
Product
Three Phase Round Energy Meter Test Bench Type KP-S3000-C
-
Bofa Instrument & Equipment Co., Ltd
Three phase Round energy meter test bench Type KP-S3000-C is designed for testing three-phase round energy meters (ANSI Socket type), it is mainly exported to countries in Noth America and South America. It is an ideal testing eqiupint for energy meter factory or R&D institute. All the testing procedures can be automatically operated by PC or by Keyboard manually.
-
Product
200W Autoranging Power Supply, 60V, 10A
E36232A
Power Supply
E36232A provides more useable power with autoranging architecture in a bench friendly design with full programmability; LAN, USB and optional GPIB interface.
-
Product
PC Based Comprehensive Test Setup for Luminaires
-
Our zest for innovation has resulted in continuous upgrades in the existing line of products. Till now we used to manufacture 3 different equipments for Driver, MCPCB and Luminaires Component testing. We at SCR Elektroniks have developed our comprehensive tester to incorporate all the 3 systems in a single bench. Here in this tester one can test all the three DUT in a single bench. Since all the 3 testing procedures have many tests in common, we have incorporated all the tests in a single bench such that testing of Luminaire driver, Luminaire PCB and Final Luminaire set is performed in single test bench. Only these tests are performed over the DUT else other are disabled for them.
-
Product
DC Bench Power
-
AMETEK Programmable Power, Inc.
From benchtop supplies to rack mounted industrial power subsystems, AMETEK Programmable Power is the design and manufacturing leader of precision, programmable power supplies. The voltage range for the AMETEK DC bench supplies is 7V to 600V and the current range is 0A to 1,000A producing a power output of 0W to 840W. Select from the models above to find the right fit for your application.
-
Product
Optical Controllers
-
Teilch’s compact DM controller for the Kilo DM is capable of delivering 16bit resolution over 220V and with dynamic range of 1kHz. System is directly integrated with the Zif Socket, eliminating the need for cables and providing a direct mechanical connection from the bench mount to the DM.
-
Product
Rubbing Fastness (Gakushin) Tester
TF413
-
TESTEX Testing Equipment Systems Ltd.
Rubbing fastness (Gakushin) Tester for JIS standards for evaluating a material’s resistance to rubbing motion. Unit is a six station, bench top machine which includes clamps for sample attachment to moving platen and clams for weighted rubbing arm for attachment of rubbing material.
-
Product
Bench Conductivity / TDS Meter
CyberScan CON 510
-
Multi-Parameter - toggle between Conductivity / temperature and, TDS/temperature at touch of buttons :: Multi-Point Push-button Calibration (Up to 5 points for Conductivity/TDS) - for easy, quick calibration :: Automatic or Manual Calibration - for quick, easy calibration; use automatic mode with preset calibration points at most popular values or manually set values in the manual mode for more flexibility
-
Product
Solar Array Simulator
G5.SAS
-
The G5.SAS series are unidirectional sources. It was developed specifically for testing inverters and simulating solar arrays and is suitable for use in laboratories and on test benches. The modular and finely graded G5.SAS series is characterized by highly dynamic response times and a wide current-voltage range with an auto-ranging factor 3. The power supplies feature especially low capacitance values in the output filter stage and switchable earth leakage resistors for adaptation to the insulation measurement of the DUT.
-
Product
*Micro-fluoroscopic X-ray Inspection System
Cath-X
-
The Cath-X is a bench top system employing Glenbrook’s micro-fluoroscopy technology providing highly detailed x-ray video of the critical components of the needle device. The transparent, safely shielded, view chamber permits the operator to locate the critical areas of the needle for inspection. The x-ray image can be further magnified using the electro-optical zoom feature of the Cath-X.
-
Product
Laser Flash Photolysis
-
This system that makes complex electronics, cumbersome software and large optical benches a thing of the past. The LFP system incorporates everything needed except the excitation laser. This is a simple, yet powerful instrument, ready to perform a wide range of time resolved kinetic and spectroscopic measurements involving transient absorption or diffuse reflectance. The LFP system, including the monochromator and digitizer is completely computer controlled, making it easy to obtain
-
Product
R + D Testing of Electric Motors
-
Highly dynamic development test bench for synchronous and asynchronous motors*Comfortable concept with changeable test angles for handling various load machines and test pieces*Freely configurable test runs - ie suitable for endurance tests and long-term examinations*Equipped for environmental simulations (temperature)*Examination of complete drive systems (motor and inverter)
-
Product
Torque Reaction Sensor
BMX
-
Meeting the demands to test multiple torque ranges for various torque tools used in production, maintenance and calibration labs, the versatile torque sensor is used in conjunction with a torque tester. The torque sensor is a bench mounted calibration instrument designed for torque wrench calibration, torque screwdriver calibration, and electric & pneumatic screwdriver calibration. Controlling torque is quintessential for companies to ensure their product's quality, safety and reliability isn't compromised.
-
Product
Bench-Top LPR Data Logger
MS6200L
-
The MS6200L is a bench-top data logger capable of measuring and storing data from all types of linear polarization resistance (LPR) corrosion probes. The instrument is microprocessor-based and features a simple, menu-driven interface using a 2-key keypad and a 2-line LCD display. It is housed in a rugged but lightweight plastic enclosure and is ideally suited for use in laboratory environments. The adjustable handle can be used for carrying the unit, or can be used as a tilt stand to adjust the viewing angle.
-
Product
USB I/Q Arbitrary Waveform Generator, 3-channel, up to 1GHz I/Q bandwidth
Streamline P9336A
Arbitrary Waveform Generator
Balance deadlines, productivity, budget and bench space with the Keysight P9336A Arbitrary Waveform Generator (AWG), a member of Keysight’s Streamline Series. You’ll move confidently across every stage of your product’s development lifecycle by leveraging accurate and repeatable measurements, automated code capability, and a consistent, intuitive user experience.
-
Product
SF6 Specialist Gas Analyzers Range
-
The Rapidox SF6 6100 Bench gas analyser is designed for controlling and monitoring the quality of SF6 gas over a range of applications, including medium & high voltage gas insulated electrical equipment, SF6 gas purity tests, medical testing, manufacturing and laboratory-based research and development.
-
Product
CIRCUIT ENERGIZER
TH852
-
*Can be used with most 12V mini jump starters with the standard EC5 port*Allows for more portability and freedom from long battery wires*Factory correct terminals means less of a need to back probe*Isolates component from the rest of the circuit which results in less damage to entire wiring/computer modules*No need to remove component for bench test
-
Product
Calibration Benches
-
CalBench is a custom built work station for industrial test facilities and calibration laboratories. A wide range of modules for calibration of electrical, pressure, temperature, and loop are available. Further modules and extras such as power supplies, oscilloscopes, and counters can also be integrated. CalBench provides the versatile solution to multi product calibration that meets the highest industry standards.
-
Product
Industrial USB 3.0 Tester
M5615B
-
International Microsystems Inc.
The M5615 tester is a 16 Socket Bench top Production and Engineering Tester that supports USB 3.0 Super Speed and USB 2.0 High Speed devices. The tester comes with a built-in PC running a full Linux operating system that tests and copies any USB storage device including USB Hard Drives at super speeds.
-
Product
80W Power Supply, 8V, 8A or 20V, 4A
E3644A
Power Supply
Keysight basic DC power supplies offer essential features for a tight budget. The single & dual output, 30-100 W GPIB E3640 series provide small, compact size for bench and system use; low output ripple and noise; and built-in measurements and basic programmable features. The Keysight 80W, single output E3644A is a stable and reliable power supply for benchtop and basic automated test applications, and enables versatile solutions for tests that require moderate speed and precision with both GPIB and RS232.
-
Product
Temperature Chamber
MTC-20
-
Improve your temperature dependent testing with the Compact Bench Top Temperature Chamber, seamlessly integrated with a Maccor Automated Test System. Its compact design allows for easy placement on any benchtop. For increased capacity, you can install up to 4 chambers into a standard 19” industrial rack cabinet.
-
Product
RF Diagnostic Chamber
DST200
-
The R&S®DST200 RF diagnostic chamber is the ideal environment for RF analysis during development. It supports a wide range of radiated test applications for wireless devices and fits on any R&D lab bench, where it can be used at all times during the product design and optimization phase. The R&S®DST200 effectively assists in achieving high first-time pass rates during final type approval, which saves time and money.
