Bare Board Test
SMT and PCB check prior to being populated with components.
See Also: Bare board, Bare Board Testers
-
Product
Ethernet Digital Interface OEM Board
8063
-
* Same Digital IO lines as standard 8063. * Same data transfer capabilities as standard 8063 * Digital I/O uses high-density DC-62 connector.* Power connections via 2 screw terminal strip or solder pads.* User configured IDN message and webserver pages makes board respond as part of your system.* Use an ICS Wiring Kit to extend the Ethernet signal to a rear panel RJ45 jack.* Runs on 9 to 32 Vdc power.
-
Product
Three-Phase Test System
TESTRANO 600
-
TESTRANO 600 is the world’s first portable, three-phase test system which supports all common electrical tests on single- and three-phase power and distribution transformers for routine and diagnostic testing on-site or during factory acceptance tests (FAT).
-
Product
JTAG Test Software
-
JTAG Technologies software has been subject to a program of continuous development for over 20 years. The first products, launched in 1991 formed the start of our 'Classic' range of software and featured the first automatic boundary-scan test program generator (ATPG) for PCB interconnects plus associated test execution and diagnostics software. In 2006 JTAG Technologies launched it's new flagship tools platform JTAG ProVision.
-
Product
Functional Test Fixtures
-
Businesses rely on Circuit Check’s functional test fixture expertise. Functional test typically applies full operational power to a loaded printed circuit board in order to determine if the PCBA performs functions as designed. This type of test often involves custom built test equipment and custom test fixturing. Circuit Check supports all forms of functional test strategies.
-
Product
Vibration Test Systems
-
HIACC Engineering & Services Pvt. Ltd.
Designed to simulate real-world vibration, shock, and environmental stresses for product reliability testing.
-
Product
High-Performance Integrated Functional Test Platform
Spectrum-9100™
Test Platform
The Spectrum-9100 is a fully integrated functional test system for factory, depot, and intermediate test applications. It’s the “go to” tester for users needing a mix of digital, analog, mixed-signal, and bus test capabilities across a wide range of products—from legacy boards to advanced systems.
-
Product
Impact Testing
-
The Impact Testing software of the m+p Analyzer real time analyzer includes useful tools like the selection of a roving hammer or transducer, selection of data points/nodes, double impact detection and rejection, definition of force and exponential window and a user-definable display configuration as a visual measurement feedback.
-
Product
Test Automation Software
-
PathWave test and measurement software delivers fast, accurate, and comprehensive data analysis. Connected workflows and trusted algorithms allow you to optimize test plans while increasing test efficiency. Designed for spectrum analyzers, oscilloscopes, network analyzers and many more test instruments as well as PCs or automation systems.
-
Product
Petroleum Testing
-
Intertek petroleum testing services support the entire petroleum products range: crude oil, refined petroleum products, refined fuels including gasoline, diesel, fuel oil, residual oil, LPG, petrochemicals, industrial gases, and natural gas. Intertek is a world leader in providing petroleum testing, petroleum sampling and petroleum inspection services to oil, chemical and related companies on a global basis.
-
Product
Wafer-Level Parametric Test
test
Wafer-level reliability engineers need to reduce test time without sacrificing measurement quality and accuracy.
-
Product
Optics Test Systems
Front Window Scanner For Wedge Angle Measurement
-
Optik Elektronik Gerätetechnik GmbH
Scanning of complete automotive windshields to measure the wedge angle and thickness change, especially in the HUD area.
-
Product
Soft Board Dedicated Automatic Testing Machine
U800FPC
-
1. CCD automatic alignment, with an accuracy of ± 10μm2. Support layout test, displacement function3. The upper and lower jigs X, Y, θ are automatically fine-tuned to improve the yield4. Soft board stretching function5. Automatic marking function6. Support SHOPFLOOR report output7. Optional BARCODE READER
-
Product
Isolated Watchdog Board
APCI-035
-
The board ADDIMULTI APCI-035 is equipped with 4 watchdogs allowing the simultaneous monitoring of multiple processes. Watchdog N? 1 works with 2 alarm levels and can be set to 1 of 4 different time bases (µs, ms, s, min). Level 1 alarms the PC cntrol and/or the monitored device. Level 2 resets the PC and/or the monitored device after a defined time. The alarm control can be accessed through 1 trigger channel and 4 different time bases.
-
-
Product
DHCP Tests
-
The Dynamic Host Configuration Protocol (DHCP) provides configuration parameters to Internet hosts. DHCP consists of two components: a protocol for delivering host-specific configuration parameters from a DHCP server to a host and a mechanism for allocation of network addresses to hosts. DHCP is built on a client-server model, where designated DHCP server hosts allocate network addresses and deliver configuration parameters to dynamically configured hosts. (Source: RFC 2131)
-
Product
Traction Test Rectifiers
-
A traction test system is defined as a rectifier with a DC output voltage above 400 VDC to a maximum of 4,500 VDC. (Kinetics manufactures only air-cooled systems) A Kinetics test system includes the required OSHA designated safety features for testing power supplies as a minimum for operator interface.
-
Product
Rapid Test Development
TestEZ® Development Suite
-
Count on the Test EZ® Development Suite for complete, efficient, cost-effective test development and execution for electronic test systems.
-
Product
MIL-STD-1553 Two-Channel PMC Board
BRD1553PMC-STD-2
-
The PMC HyperBoard is a multi-standard PCI Mezzanine Card that contains two channels of MIL-STD-1553 communication. The board is compatible with MIL-STD-1553B and MIL-STD-1760. Each channel can be configured independently to work with H009 and WB-194 in conjunction with MIL-STD-1553.
-
Product
Board Connectors
-
Advanced Interconnections Corp.
High density designs maximize board spaceScrew-machined terminals for superior performanceSurface mount, spring pin, and thru-hole solutions
-
Product
Circuit Testing
Tester, Circuit GFI
-
*Use to troubleshoot 120 VAC grounded outlets and test GFCI receptacles*Light sequence indicates correct/incorrect wiring*Lifetime Limited Warranty
-
Product
Test Automation
-
Test automation can be the solution to releasing new features and functionality with reduced time to market and uncompromising quality. There will, however, always be times when manual testing is the most appropriate approach.
-
Product
5G Testing
-
Teradyne test solutions are at the forefront of the 5G test era. Why? We work with the leading semiconductor manufacturers and provide optimized test coverage for the major wireless standards. From emerging millimeter wave devices to the traditional sub-6GHz, our test solutions are already leading the way.
-
Product
Cable Test Van
-
Techno Instrumentation (India) Private Limited
Cable fault locating van with installation according to users specifications and requirement.
-
Product
Cable Test Van
BAUR Transcable 4000/S 70-3
-
Transcable 4000/S 70-3. The transcable 4000 70 kV 3/S cable test van varies in comparison with the transcable 32 kV - 3S in the 70 kV voltage level. The system is controlled with the MGS semi-automatic control unit. The high voltage switch unit is 3-phase, air and solid matter insulated and safe to touch.
-
Product
Industrial Grade PCI DIO 96 Board
MS 1817
-
*96 digital input/output lines*Support s all PPI Modes (Mode0, Mode 1 and Mode 2)*5 V TTL/CMOS*Compatible with NI DIO Card*2-wire handshaking capability*Known power-up
-
Product
Test Sockets
Non Standard
-
Chances are good Ardent can help you with that. We can adapt our technology to just about any package, device or module. Small volumes of custom sockets for higher bandwidth applications are a niche all in their own, and our engineering team has many years of experience designing custom sockets for all kinds of applications.
-
Product
Battery Testing Equipment
-
Mainly for battery testing in lab,such as 5V1mA, 5V10mA, 5V50mA,5V100mA, 5V1A,5V3A,5V6A,5V10A
-
Product
CPCI Or PXI PCM & ARINC 717 Board
MS 1703
-
*Bus Interface - PXI / CPCI Bus*Microprocessor and FPGA design based Board*One Channel ARINC 717 Transmitter and Receiver*Generates all PCM telemetry signals like NRZ, Bi-Phase, Differential Bi-phase, DM signals*Used to test all types of PCM based telemetry equipments*Configurable output signals format (parity, word length, Minor, Major frame, Bit position)*User can configure the words and there positions in the frame*The word can be either a square / triangle wave data or constant data*1 MB Shared Memory for Data Storage*Driver interface for Windows2000/XP/VISTA and LINUX OS
-
Product
Test Benches
-
Our range of test benches is designed for accurate measurement, performance validation and quality control of electrical components and systems. They provide standardised and customised AC and DC testing, with variable signal frequencies and waveforms.
-
Product
6U VPX UltraScale™ FPGA board with FMC+ sites
IC-FEP-VPX6e
-
Based on the latest Xilinx Kintex UltraScale™20nm FPGA, the IC-FEP-VPX6e is a 6U OpenVPX Front-End Processor (FEP) optimized for applications requiring DSP intensive processing in highly constrained environments.
