-
product
Development System
FE-51CC01
* Emulates Atmel T89C51CC01/2 and T89C51AC2, T89C5115 * 60K Code Memory * Real-Time Emulation * Frequency up to 20MHz/3V, 33MHz/5V * ISP and X2 Mode Support * MS-Windows Debugger For C And Assembler * Emulation Headers and Signal Testpoints * Target Board and Programmer Included * Serially Linked to IBM PC at 115Kbaud
-
product
DDR4 Pro 288-Pin DIMM Adapter
INN-8686-18-PRO
Your best option if you need to test a large volume of memory! The RAMCHECK LX DDR4 Pro 288-pin DIMM Adapter (p/n INN-8686-18-PRO) gives RAMCHECK LX users the power to test 288-pin DDR4 modules, including unbuffered (UDIMM), load-reduced (LR-DIMM) and registered modules (RDIMM), both ECC and non-ECC, that comply with JEDEC standards. It includes the DDR4 Series adapter and DDR4 Pro DIMM test head.
-
product
DH Series High-Sensitivity Solder-In Tip, 30 GHz BW, 2.0 Vpp Range
DH-SI-HS
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Silicon Test & Yield Analysis Solutions
Tessent®
The Tessent product suite combines features of deterministic scan testing, embedded pattern compression, built-in self-test, specialized embedded memory test and repair, and boundary scan, as well as board and system-level test technologies. This comprehensive silicon test and yield analysis solution is built on the foundation of the best-in-class solutions for each test discipline
-
product
MIL-STD-1760
M4K1553Px(S)-1760
The M4K1553Px(S)-1760 interface module for the multimode, multiprotocol, Excalibur 4000 family of carrier boards provide a complete solution for developing and testing MIL-STD-1760 interfaces and performing system simulation of the MIL-STD-1760 bus. The module handles all standard variations of the MIL-STD-1760 protocol.Each M4K1553Px-1760 multi function module contains 64K bytes of dual-port RAM for Data blocks, Control registers, and Look-up Tables. All Data blocks and Control registers are memory mapped, and may be accessed in real time. Each of the independent dual redundant M4K1553Px-1760 modules may be programmed to operate in one of three modes of operation: Remote Terminal, Bus Controller/Concurrent-RT, and Bus Monitor. In addition, modules 1 and 3 can be programmed to operate as Concurrent monitors, to modules 0 and 2 respectively.
-
product
Nand Flash Tester
NplusT
NplusT was created in December 2002 by Tams Kerekes' 20-years experience in the field of electrical semiconductors and reliability testing.The company started with the sales representation of semiconductor equipment and consumable suppliers. In the meantime, qualified engineering services, linked to the represented products, were provided in Europe.In 2003 NplusT started to market "RIFLE", the non-volatile memory engineering tester, and related services. In a few years, this product has become a reference platform for many memory makers.In 2005 Liliom Laboratories, a Hungarian software development company, merged into NplusT. Thanks to this operation, the company became leader in the test data collection and processing segment.From 2008 a dominant portion of NplusTs turn-over derived from licensing software products. Today almost every European along with several Far East semicon companies license our software products and make use of qualified engineering services.From 2011, NplusT provides turn-key solutions for device testing and characterization, including hardware, software and support.
-
product
Oscilloscope 500 MHz, 2 Analog Channels
DSOX3052G
The DSOX3052G 500 MHz oscilloscope provides 2 analog channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
product
Thermo-Hygrometer
D3121-2
Thermometer, hygrometer is designed for measurement and datalogging of temperature, relative humidity into the internal non-volatile memory.
-
product
Infiniium V-Series Oscilloscope: 20 GHz, 4 Analog Channels
DSOV204A
20 GHz analog bandwidth (upgradable)4 analog channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.54 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Improve your testing with the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
ECHO 7 Ultrasonic Precision Thickness Gage
ECHO 7
ECHO 7 represents our most advanced thickness gage ever. ECHO 7 offers a 3.5” high resolution sunlight readable color display with live A-Scan, use of a wide variety of contact, delay line and immersion probes from 1-20 Mhz as default and custom created and stored applications setups, B-Scan, datalogger with up to 32GB of SD card memory and interface to Microsoft excel. The ECHO 7 is available in 4 models including the ECHO 7, ECHO 7DL, ECHO 7W and ECHO 7DLW.
-
product
M.2 PCIe3 NVMe RunCore Consumer SSD “Sprinter Series”
RunCore Innovation Technology Co. Ltd.
M.2 PCIe3 NVMe Solid State Drive (SSD) is a high capacity solid-state flash memory product that complies with the PCIe Gen 3 standard and is functionally compatible with a PCIe protocol.
-
product
Datalogger
S0110E
Temperature datalogger is designed for record of temperature. Values are stored to a non volatile electronic memory. Data transfer to the personal computer for further analysis is performed via USB, RS232, GSM or Ethernet interface by means of a proper adapter.
-
product
3U PXI-E System Controller
PX32101
LinkedHope Intelligent Technologies Co.,Ltd.
PX32101 is a 3U PXI-E system controller based on the newest Intel® Haswell platform. It is designed to provide comprehensive and reliable system controller to support hybrid PXIe-based systems for multiple environments test and measurement applications.Hybrid PXIe-based systems are often required to complete independent diversified complex testing tasks on the PXI test platform. PX32101 provides rich interfaces: 4 USB2.0 / 3.0 for peripheral connectivities; UART for communication or control equipment; dual 1000Base-T Ethernet, one port for LAN connection and the other one for the control of the next generation of LXI instruments. PX32101 can support 4 x4 or two PCIe x8-link, and up to 16GB / s system bandwidth. The ExpressCard 34 expansion slots on the front panel allow users to expand the system modules flexibly. If you install a hybrid multi-slot backplane in the system, then various standard PXI-E and PXI / CPCI peripheral cards could be fitted. In a multitasking environment, PX32101 processor is able to complete multiple tasks independently. The CPU and memory chips soldered with PCB increase reliability performance in shock and vibration environments. Combined with a variety of instrument control interfaces and reliable mechanical & electronic design, PX32101 can meet your hybrid PXIe-based testing for system application requirements perfectly.
-
product
Extended ATX Industrial Motherboard
The C62EX server-class motherboard supports the 3rd Gen Intel Xeon Scalable processors, achieving high-performance and power efficiency, and is optimized for storage, security, and communications applications.3 PCIe x16 and 2 PCIe x8 slots allow ample room for add-on cards, and the slimline and OCP connectors give you a multitude of storage and communications options. Dual processor support, and 16 DDR4 ECC memory slots make sure enough performance is available at your fingertips.
-
product
DC Coupled, 14-Bit Digitizer For ExpressCard 54, 2 Channels 150 MS/s
EC14150D
The EC14150D (EC) is an DC-coupled dual channel waveform capture board that provides a remarkable combination of high speed and high resolution sampling along with a very large memory capacity all in a very compact and low power consuming ExpressCard form factor. At 4.5 W, the EC represents one of the lowest power consuming digitizer cards ever created for its class. Signal frequencies up to 200 MHz can be accurately captured either in baseband or in higher order Nyquist zones using under-sampling techniques. Where DC-coupling is required, the EC14150D should be considered.
-
product
25 GHz Differential Probe with 2.92mm Interface
DH25-2.92MM
Teledyne LeCroy’s DH series 8 to 30 GHz differential probes offer the combination of bandwidth, input range and offset capability to address any high-speed probing requirement from debugging serial data interfaces to validating DDR memory systems. DH series probes provide superior loading characteristics and are calibrated with a custom “fine-tuned” frequency response. The ultra-low loading and flat frequency response ensure accurate measurements.
-
product
Mixed Signal Oscilloscope: 200 MHz, 2 Analog Plus 8 Digital Channels
MSOX2022A
200 MHz2 analog plus 8 digital channels Easily view your signals on the 8.5-inch WVGA display Capture more data with up to 1 Mpts memory See more signal detail with 50,000 wfms/s update rate Expand your measurement capabilities with full upgradability: Add 20 MHz function generator, 3-digit voltmeter, serial trigger and analysis, segmented memory & mask testing at any time Easily set up teaching labs with our free Educator's Resource Kit
-
product
Mixed Signal Oscilloscope: 13 GHz, 4 Analog Plus 16 Digital Channels
MSOV134A
13 GHz analog bandwidth (upgradable)4 analog plus 16 digital channels Capture a longer signal trace with up to 80 GSa/s sample rate and 2 Gpts of acquisition memory Get the best signal integrity with the low noise floor (1.09 mVrms at 50 mV/div) and lowest jitter measurement floor (100 fs)See better measurement accuracy with ENOB values in excess of 5.5 and a SFDR exceeding 50 dBC Access the broadest range of jitter, trigger, analysis and protocol tools (featuring Precision Probe)
-
product
Industrial ATX Motherboard with 6th/7th Gen Intel® Core™ i7/i5/i3 Processor (Code name: Skylake/Kabylake)
IMB-M43
The ADLINK IMB-M43 is industry's first 6th/7th Gen Intel Core i7/i5/i3 Processor (formerly codenamed Skylake/Kabylake) based industrial ATX motherboard in the LGA1151 package with Intel Q170 Express chipset. The ADLINK IMB-M43 supports high-speed data transfer interfaces such as PCIe3.0, USB 3.0, and SATA 6 Gb/s (SATA III), with dual-channel DDR4 2133/2400 MHz memory up to 64 GB in four DIMM slots.
-
product
DDR4 Parametric Test Reference Solution
Keysight's DDR4 parametric test reference solution helps verify the signal integrity of DDR4 memory designs according to JEDEC specifications.
-
product
VPX Image & Video Processing and GbE Data Transmitting Board
VP69702
LinkedHope Intelligent Technologies Co.,Ltd.
Based on AMD Radeon™ E8860 GPU and Intel 82599ES controller, VP69702 is a VPX image & video processing and 10GbE data transmitting board mainly designed for applications of embedded image & video processing, GPGPU and 10GbE data transmitting.On VP69702, there are 2 independent display outputs routed to front and 2 10GbE interfaces. The GPU of VP69702 is equipped with 2GB GDDR5 video memory, 768/48 GFLOPS single/double precision peak processing ability and 640 shader processing units. VP69702 is highly suitable for HD output (1920x1080), 4K output (3840x2160), high-performance parallel computing and other applications and fields.
-
product
Ethernet/LXI generatorNETBOX 16 Bit Arbitrary Waveform Generator - up to 125 MS/s on 4 Channels, up to 80 MS/s on 8 Channels
DN2.656-08
The generatorNETBOX DN2.65x arbitrary waveform generators (AWG) is a general purpose multi-channel AWG with outstanding dynamic performance. The series includes LXI units with either four, eight or 16 synchronous channels. The large onboard memory can be segmented to replay different waveform sequences.
-
product
PCI Multi-Functions Board
PCI-DSP-6713-MFIO
The board consists of private SDRAM and dual-ported SRAM attached to the DSP. An FPGA provides the timing and control as well as I/O drive for the 48 programmable I/O pins. Peripherals include a serial port and an USB port. Flash memory is available for downloading programs into a non-volatile memory. 16 channels of A/D and 16 channels of D/A provide analog interfaces to real-world signals
-
product
PCIe 16 Bit Multi-purpose Digitizer - up to 40 MS/s on 8 Channels (Single Ended) or 4 Channels (Differential)
M2P.5933-X4
The M2p.59xx series allows recording of up to eight single-ended channels or up to four differential channels both with sampling rates of up to 125 MS/s. These PCI Express cards offer outstanding A/D features both in resolution and speed. The cards can be switched between single-ended inputs with a programmable offset and true differential inputs. If used in differential mode each two inputs are connected together reducing the number of available channels by half. The 16 bit vertical resolution have four times the accuracy compared to 14 bit cards and sixteen times the accuracy if compared with a 12 bit card. All boards of the M2p.59xx series may use the whole installed on-board memory of up to 512 MSamples completely for the currently activated number of channels.
-
product
Mixed Signal Oscilloscope 1 GHz, 4 Analog Plus 16 Digital Channels
MSOX3104G
The MSOX3104G 1 GHz oscilloscope provides 4 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
product
SKYbolt II 6U VME 8-Slot
Delivering performance of 16 GFLOPS the SKYbolt II 6U VME solution adds intelligent support for system services and high-performance data transfers as the carrier board for the Merlin daughtercard which contains the compute processors, I/O interfaces, and global memory
-
product
COM Express Type 6 Compact Module With 6th Gen Intel® Core™ I7/i5/i3 And Celeron® Processor
CEM501
The CEM501 COM Express Compact Type 6 module is based on the latest 14nm 6th generation Intel® Core™ i7/i5/i3 processors (codename: Skylake) with support for up to 32 GB dual channel DDR4 SO-DIMM memory. Featuring improved processing and graphics performance compared to the previous generation Intel® processor, the compact-size system on module CEM501 offers intense graphics performance and multitasking capabilities, making it ideal for telecommunication, medical imaging, digital signage, gaming machines, military, and IoT related applications.
-
product
CPCI ARM LPC3250 Board
MS 1513
- 32 Bit ARM LPC3250 Processor (256KB SRAM)- 133MHz External Bus Speed and 266 MHz internal CPU Speed- 32 Bit, 33MHz CPCI Bus, 6U Form Factor- External memory ( Flash – 2 MB, RAM - 512 KB, DPRAM – 128KB)- 10/100 MBPS Ethernet Interface- USB 2.0 Host/Device Interface- 2 RS232 Serial Ports, 4 RS422 Serial Ports- M Module Interface- 6U board compatible with CPCI & PXI backplanes- High Speed Logic Device- Hot Swap Feature- Front Panel and Rear IO Interface- External Bus through Rear IO- Reception of 3Kbytes within 2ms through Ethernet- Board Dimension is 160mm x 233.35mm- Power Requirements: +3.3V, +5V and +/-12V- Board Dimension is 160mm x 233.35mm- Board has Rear IO interface- Ethernet, JTAG, RS232, USB connectors at front side- BSPs and Driver software for Windows and Linux OS
-
product
Mini-ITX SBC With LGA1150 Socket 4th Gen Intel® Core™ Processor, Intel® H81, HDMI/VGA/LVDS, Dual LANs And USB 3.0
MANO881
The MANO881 Mini-ITX motherboard with Intel® H81 Express chipset supports the 4th generation Intel® Core™ and Celeron® (Haswell) processors. This feature-rich Industrial SBC has two sockets for DDR3 system memory of up to 16 GB. The high-performance mini-ITX motherboard MANO881 supports one PCIe x16 slot and integrated with Intel® HD 5000 graphics supports powerful graphic processing and dual-display capability through HDMI, VGA and LVDS interfaces. The outstanding embedded board also includes rich I/O expansions which can help system integrators to develop solutions quickly at a more competitive price. The MANO881 is excellent for in-vehicle PCs, medical imaging and gaming devices, in-flight entertainment systems, industrial automation systems, and other portable devices.
-
product
Hostless Wi-Fi IoT Module
SX-ULPGN-DB
The SX-ULPGN-DB is a low-power , cost effective hostless Wi-Fi IoT module with 802.11 a/b/g/n support. This low power Wi-Fi IoT module is based on QCA4012 radio from Qualcomm. SX-ULPGN-DB is a feature-rich intelligent Wi-Fi solution for IoT that integrates a full Wi-Fi stack, full networking/security stack, and embedded CPU and memory for on-chip application development.
