-
Product
16 Bit PCIe Gen-2 Digitizer / Oszilloscope 4 Channel 200 MS/s B. 8 GS Memory
-
The GaGe RazorTM family of multi-channel digitizers features up to 4 channels in a single-slot PCI Express or PCI card with up to 200 MS/s sampling per channel, and up to 8 GS of on-board acquisition memory.
-
Product
Single / Dual channel Dual Redundant DDC Controller
PCI-1553DDC-2
Controller
The PCI-1553-DDC-1/2 implements a complete single channel dual-redundant MIL-STD-1553 bus terminal on a half size PCI Card. Full BC/MT/RT modes are supported. 0°C to 70°C operating temperature is standard. Included is an DDC Enhanced ACE intelligent communications protocol engine, dual transceivers and encoder / decoders, shared memory, and management logic.
-
Product
Minirator
MR-PRO / MR2
-
The Minirator MR-PRO provides a full set of analog audio signals including sine wave, pink noise, white noise, delay test signal, polarity test signal, stepped sweep and continuous sine sweep. Further, a set of wav-files, useful for system optimization, is stored in the internal flash memory. Add your own personal favorites to this set.
-
Product
Mini-ITX SBC With LGA1151 9th/8th Gen Intel® Core™ I7/i5/i3 Processor, DisplayPort++, VGA, EDP, USB 3.0, M.2 And Dual GbE LAN
MANO523
-
*LGA1151 9th/8th gen Intel® Core™ i7/i5/i3 processor*Intel® Q370 chipset*2 DDR4 SO-DIMM for up to 32GB of memory*4 USB 3.0 and 4 USB 2.0*6 COM ports*2 SATA-600 and 1 M.2 Key M*PCIe x16 and M.2 Key E
-
Product
Conduction Cooled VPX Interface Board with PCI Express Host Interface
EXC-8000ccVPX
-
The EXC-8000ccVPX is part of the 8000 family of multiprotocol carrier boards. This conduction cooled VPX interface board has a PCI Express host interface and can support up to four independent removable modules and 10 on-board Discrete channels. Each removable module can be any of the 8000 family modules.The EXC-8000ccVPX supports Direct Memory Access (DMA), which enables the board to access system memory for reading and writing independently of the computer’s CPU. This results in faster data transfer to and from the board, with much less CPU overhead than when not using DMA.The EXC-8000ccVPX is supplied with C drivers, including source code. Mating connector provided for I/O connection.
-
Product
Dynamically Controlled High Speed Digital I/O PXI Card
GX5290 Series
Digital I/O Module
The GX5290 Series are a high performance, cost-effective 3U PXI dynamic digital I/O boards offering 32 digital input or output channels with dynamic direction control. The GX5290 Series also supports deep pattern memory by offering 256 MB of on-board vector memory with dynamic per pin direction control and with test rates up to 200 MHz. The single board design supports both master and slave functionality without the use of add-on modules.
-
Product
16-bit, 100KHz, 16SE/8DIFF A/D Inputs; 8 14-bit, 30KHz D/A Outputs, 4 24V Digital I/O, All Isolated
CPCI-3120-16-8
-
Input range:?± 10 V, 0-10 V software programmable0-5 V, ± 5 V, 0-2 V, ± 2 V, 0-1 V, ± 1 V (gain)0-20 mA (option) ? software-programmable amplifier:PGA x1, x2, x5, x10 ? Conversion triggered through software,scan, timer, external event ? Onboard FIFO buffering for 256 analog values ? Data exchange through 16-bit I/Oor 32-bit memory (PCI DMA) ? Sequence RAM ? Overvoltage protection ? input filter: 160 kHz
-
Product
Rugged PC Compatible
SYS-ITX-N-3800
-
WINSYSTEMS’ SYS-ITX-N-3800 is a NANO-ITX Industrial Computer (SBC) based on the Intel® Atom™ E3800 Bay Trail processor family. It uses less than 10 watts for fanless applications and performs reliably in industrial operating temperatures ranging from -25º to +60ºC. It includes a SODIMM socket supporting up to 8 GB of DDR3 system memory and internal mounting support for one 2.5” SATA HDD/SSD. Additional expansion is available through MiniPCIe.
-
Product
LAN Router
BB-SR30010121
Router
SmartFlex, Global, 5x Ethernet, Wi-Fi, Metal, EU Accessories. VPN, Multiple LAN/WAN configuration, DIN rail mounting. Powerful CPU and Memory, Hosting of SW IoT applications.
-
Product
PCI Express Graphic Card NVIDIA RTX 4000E Ada
NVIDIA RTX 4000E Ada
Graphics Card
- NVIDIA Ada Lovelace Architecture- 5-year Longevity Support- Full height, full length design- PCIe Gen4x16 interface- 20GB GDDR6 Memory, 160-bit Bandwidth- 6144 CUDA Cores, 26.7 TFLOPS SP Peak
-
Product
Robust DIN-rail Fanless Embedded System With Intel® Celeron® Processor N3350/Pentium® Processor N4200, Isolated COM, LAN And DIO
ICO300-83B
-
The ICO300-83B is powered by the low-power consumption Intel® Celeron processor N3350 (Formerly codename: Apollo Lake). ICO300-83B’s proven rugged construction ensures harsh operating conditions with an extended temperature range of -20°C to 70°C (-40°C to +70°C for option), a wide voltage range of 12V-24V DC power input with overvoltage and reverse protection, and up to 2G vibration endurance. It supports one DDR3L-1866 SO-DIMM slot with up to 8 GB of system memory. Additionally, the ICO300-83B is equipped with two full-size PCI Express Mini Card slots, one for an mSATA storage card and another for 3G/GPRS/Wi-Fi - allowing it to provide flexible communication and data transfer options for use as an IIoT gateway.
-
Product
3.5” Embedded SBC With AMD® RYZEN™ Embedded V1807B/V1605B APU, DisplayPort, 2 HDMI, LVDS And 4 GbE LAN
CAPA13R
-
The CAPA13R is powered by the onboard AMD RYZEN™ Embedded V1807B/V1605B processor with Radeon™ Vega graphics. The 4K embedded board is well-suited for graphics-intensive applications such as medical imaging, video surveillance, 3D simulators, optical quality control, digital signage, kiosks/POI, thin clients, and more. The integrated AMD RadeonTM RX Vega graphics with support of DirectX 12 and OpenGL 4.5 marks the cutting edge of embedded graphics. The CAPA13R can deliver truly impressive user experiences and outstanding 3D graphics quality through two HDMI, one DisplayPort and one LVDS interfaces. Its onboard CPU is attached on the rear side of the board, which can aid with heat dissipation and offers flexibility for easy system integration and minimum maintenance. Moreover, the CAPA13R offers multiple expansion interfaces with one M.2 Key E slot for wireless modules and one M.2 key B slot for storage cards. One 260-pin SO-DIMM socket on the CAPA13R supports up to 16GB of DDR4-2400 (V1605B) and DDR4-3200 (V1807B) memory. The system has a +12V DC power input.
-
Product
6U VPX double-GPU Image & Video Processing Board
VP69701
-
LinkedHope Intelligent Technologies Co.,Ltd.
Based on AMD Radeon™ E8860, VP69701 is a VPX double-GPU image & video processing board mainly designed for applications of embedded image & video processing and GPGPU.On VP69701, there are 4 independent display outputs routed to front and 2 GPU. Each GPU of VP69701 is equipped with 2GB GDDR5 video memory, 768/48 GFLOPS single/double precision peak processing ability and 640 shader processing units. VP69701 is highly suitable for HD output (1920x1080), 4K output (3840x2160), high-performance parallel computing and other applications and fields.
-
Product
PCIe LVDS Digital Waveform Acquisition - 250 MBit/s Internal Sampling Rate Timing, 250 MBit/s External State Clock
M4I.7725-X8
Digital Waveform
The M4i.77xx-x8 series digital waveform acquisition (logic-analyzer) cards include versions with 32 synchronous channels, either single-ended with programmable threshold levels or differential. The large onboard memory can be segmented to record different waveform sequences. While the M4i.77xx cards have been designed using the latest technology they are still software compatible with the drivers from earlier Spectrum digital acquisition cards. Therefore existing customers can use the same software they developed for a 10 year old 60 MS/s digital input card also for an M4i.77xx series 720 MS/s logic analyzer.
-
Product
Xcelera Frame Grabber
Xtium-CLHS PX4
-
Building on the field proven capability of Teledyne DALSA’s Xcelera frame grabber series, the Xtium™-CLHS PX4 is based on AIA’s CameraLink HS standard and uses PCI Express™ Gen 2.0 expansion bus to deliver high speed image acquisition and image transfer to the host memory. Xtium-CLHS uses industry standard CX4 cable to delivery up to 2.1 GB/s of image acquisition over a single cable to go beyond 15m and host transfer speeds of up to 1.7GB/sec - all in a compact, half-length, single slot solution.
-
Product
COM/SOM Modules
PicoZed Family
-
Computer on Modules and System on Modules are complete embedded computers with a computer processor, chipset, memory, and peripherals designed into a single board with a small footprint. They integrate the complete functions of a computer in to a single module. Both COMs and SOMs are types of single board computers except the fact that both of these are required to be mounted on a carrier board/base board which breaks the bus out to standard peripheral connectors as COM/SOM lacks the standard connectors for any input/output peripherals to be attached directly to the board. Carrier boards can implement special I/O interfaces, additional memory devices, and connectors according to the application requirements. COM examples include COM-Express Basic, COM-Express Compact, COM-Express Mini, QSeven, ETX etc. SOM examples are NOVSOM, MitySOM, and SOM CM7120 etc.
-
Product
Multiparameter CTD with a Wide Choice of Standard Sensors.
MIDAS CTD+
-
Featuring Valeport’s latest 400 Series electronics, the CTD+ will sample all fitted sensors at exactly the same instant, at up to 8Hz. Advanced setup software allows a variety of sampling regimes including burst modes, delay starts and conditional sampling. Available with up to 64Mbyte memory and internal battery pack, as well as a selection of real-time output formats, the CTD+ may be used with Valeport’s own water bottle carousel.
-
Product
4/8-CH 12-Bit 1 MS/s Analog Output Multi-Function PXI modules
PXI-2502
Multifunction I/O
ADLINIK PXI-2501 and PXI-2502 are high-speed, high-performance analog output multifunction PXI modules. These devices are able to update up to 8-CH, 12-bit analog outputs imultaneously sustaining 1 MS/s. The reference sources and output polarities are programmable individually per channel. Combine this with the multiplying PXI architecture, ADLINK PXI-2500 series PXI modules can generate complex modulated analog signals. The hardware-based arbitrary waveform generation frees CPU intervention even when all analog outputs are updating at full speed, and the lengths of waveforms are only limited by the system memory. The PXI-2500 series integrate up to 8-CH, 400 kS/s, 14-bit single-ended analog inputs with programmable polarity, 24-CH programmable digital I/O lines, and 2-CH 16-bit general-purpose timer/counters.
-
Product
AXIe High-Speed Digitizer/DAQ, 8-bit, 1 GS/s, 32-ch
M9709A
Digitizer
Based on the AXIe standard the M9709A is an 8-bit digitizer, able to capture signals from DC up to 500 MHz at 1 GS/s with excellent measurement accuracy across 32 synchronous channels within a single card. The digitizer also enables long acquisitions with its very large on-board memory of up to 16 GB.
-
Product
PCIe 3.0 Protocol Analyzer
Summit T34
Protocol Analyzer
The Teledyne LeCroy Summit T34 PCI Express protocol analyzer is designed for PCIe storage, add-in card and embedded application developers. It supports x1 to x4 lane widths with the capability of expanding to x8 with two boxes connected together, and deep buffer memory that is expandable from 4GB to 64GB ideal for storage analysis, the Summit T34 provides unmatched capability and flexibility for developers and users of advanced PCI Express products. Teledyne LeCroy has been the leader in NVM Express and SATA Express protocol analysis since 2010. This storage analyzer incorporates all of these powerful legacy features and adds the latest in storage queuing performance analysis.
-
Product
Mixed Signal Oscilloscope 500 MHz, 2 Analog Plus 16 Digital Channels
MSOX3052G
Oscilloscope
The MSOX3052G 500 MHz oscilloscope provides 2 analog plus 16 digital channels, 4 Mpts memory, 1,000,000 waveforms/sec update rate, zone touch trigger with an 8.5-in capacitive touch screen, and standard embedded software with waveform and measurement histograms.
-
Product
Reflective Memory
-
An innovative solution designed to provide highly deterministic data communications for your real time applications such as distributed simulation.
-
Product
SparkFun SD/MMC Card Breakout
-
With SD and MMC memory prices dropping, the time is right for mass storage and datalogging. This breakout board will allow you to breakout the SD/MMC socket to a standard .1" 10-pin header. Perfect for breadboarding and the likes. Board comes fully assembled and tested as shown.
-
Product
DDR Detective Logic Analyzer
DDR4
-
NOW supports 3DS at 3200MT/s!Provides logic analyzer like deep transaction Listing and Waveform capture. Continuous Capture for Violations and Performance metrics NOT a fill memory and then post process like other tools. This is a FuturePlus ONLY feature!
-
Product
Dual/Quad 125 MS/s VXI Arbitrary Waveform Generator
3164
Waveform Generator
The Racal Instruments™ 3164 Series is a single-wide VXIbus Module. The 3164-2 has two 14-bit Arbitrary Waveform Generator (AWG) channels that operate independently, and the 3164-4 AWG has four channels. The maximumsample rate for each channel is 125 MS/s. All waveforms can be sampled from data previously loaded into waveform memory or loaded and output on the fly.
-
Product
Fanless Embedded System With 7th Gen Intel® Core™ I7/i5/i3 & Celeron® Processors, Built-in Layer 2 Managed PoE Switch For Railway PC
tBOX400-510-FL
-
The tBOX400-510-FL is a two-in-one transportation-certified box PC with built-in layer 2 managed PoE switch for IP surveillance applications. The tBOX400-510-FL is certified with CE (Class A) and FCC and is in compliance with EN 50155 and EN 45545-2. This high-performance transportation box PC is powered by the 7th generation Intel® Core™ (Kaby Lake) or Intel® Celeron® 3965U processors, along with dual DDR4 SO-DIMM slots for up to 32GB of memory. The built-in 10-port managed switch is powered by Qualcomm's chip. The tBOX400-510-FL has a built-in 10-port managed switch with 8-port 10/100 Mbps PoE and 2-port Gigabit LANs, featuring VLAN, QoS and PoE scheduling for the more secure and smooth network. For reliable operation in severe environments, the rugged fanless transportation box computer is designed to withstand a wide temperature range from -40°C to +60°C and vibration of up to 3 Grms. It also supports a wide voltage input range: 9V to 36V DC for vehicle applications, 14V to 32V DC for marine applications, and 24V to 110V DC for railway applications. With its high performance, industrial-grade design and full-strict certifications, the tBOX400-510-FL is suited for transportation-related applications such as onboard video surveillance and video management.
-
Product
AC Ground Bond Testers
440 Series
-
The 440 Series provides advanced 4-in-1 test capability in a convenient one-box solution. This new series performs AC Hipot (448 - 500 VA), DC Hipot, Insulation Resistance and 40A AC Ground Bond tests while taking up minimal production line space. The 440 Series is simple and easy-to-use; reducing setup time and increasing production line throughput for your application. With multiple memories and an optional USB port for remote BUS communication so you can quickly perform tests on a variety of DUTs from the front panel or with a PC. Learn about our 5 Year Warranty.
-
Product
Qseven V2.0 SoM Evaluation Kit With Quad/DualLite 800 MHz (Industrial) SoC, 1GB Memory, 4GB EMMC, Gigabit Ethernet, Audio And CAN
Q7M120-120-EVK
-
*Ultra low power consumption Cortex™-A9*High flexibility Qseven v2.0 compliant design*2 CAN 2.0B*18/24-bit TTL LCD*LVDS/HDMI 1080P*10/100/1000 Mbps Ethernet*Linux3.0.35/Android4.3*Audio
-
Product
6U Compact PCI Single Board
CP62005
-
LinkedHope Intelligent Technologies Co.,Ltd.
CP62005 is a 6U CompactPCI® single board with high-performance, low power consumption and high reliability. It is ideal for ruggedized systems requiring high-bandwidth processing, or for information processing and embedded computing.CP62005 supports 4th generation Intel® Core™ i7 or i5 Haswell processors, up to 16GB onboard DDR3L memory. It also offers 16GB onboard SLC SSD for operating system and drivers. The onboard design of memory and SSD can enhance the anti-shock and vibration performance.CP62005 integrates Intel® HD Graphics 4600 controller, which supports a variety of display outputs, such as eDP/DP/HDMI/DVI/VGA… CRT max resolution is up to 2048x1536. With HDMI/DP/eDP it can be up to 4K. It also supports three independent displays.
-
Product
32GB DDR4-3200 2GbX8 1.2V Samsung Chip
AQD-D4U32GN32-SB
Memory Module
32GB, Speed 3200MHz, 30u" Gold Plating Thickness, Anti-sulfurization resistance, Unbuffered.
