Strain Gages
measure of displaced surface elements.
See Also: Strain Gauges, Strain Gage Amplifiers, Strain Gage Signal Conditioners, Strain
-
Product
Economic Type Strain Gauge/Load Cell Indicator
CS1-SG
-
CS1-SG economic type strain gauge/load cell indicator is equipped with high accuracy measurement, display and communication of DC signal 0~1.0/~4.0mV or 0~10.0/~40.0mV.It supports field calibration, and It can calibrate with sensor (load cell/strain gauge) according to actual needs.It is able to select one from these three functions, 1 relay output, 1 analogue output or 1 RS-485 (Modbus RTU Mode) interface; they provides many functions such as control, alarm, re-transmission, and communication.
-
Product
Stainless Steel Schaeffer Gage
SGP
-
The Series SGP Gages have dual English/metric scales with ±1.6% full scale accuracy. The Series SGP gages are designed with 304 SS housings, a 316L SS chamber and a 316 SS diaphragm for excellent chemical compatibility.
-
Product
Cable Tray, Slide Configuration, For Strain Relief And Cable Management, For 28" And Longer
310113424
Cable Tray
Strain Relief.
-
Product
Isolated Strain Gauge Input Module
ADAM-3016
-
1000 VDC 3-way optical isolationSwitch configurable mV or V input of full bridgeSwitch configurable voltage and current outputs
-
Product
Fiber Strain Measurement System
SPL500
-
The SPL500 is a fiber strain measurement system that measures fiber elongation and attenuation simultaneously during mechanical stressing of the cable. The SPL500 is designed to produce accurate measurements quickly and with confidence.
-
Product
Instrument Bracket Kit With Strain Relief, Slide Configuration, For 28" And Longer
310113453
Instrument Bracket
Strain Relief
-
Product
Pressure, Strain And Shock Data Loggers
-
Dataloggers for pressure, bridge input for strain or load measurement and also tri-axial shock dataloggers with built in accelerometers.
-
Product
Digital Image Correlation System for Complete 3D Warpage, Thermal Expansion, and Strain Analysis of Materials and Components in the Heating and Cooling Phase
Q-400 TCT
-
The Q-400 TCT system is designed for complete three-dimensional and highly sensitive warpage, thermal expansion measurement and strain analysis of materials and components in the heating and cooling phase. Areas from 50 mm x 70 mm down to 2 mm x 3 mm can be investigated. Measurements can be done from room temperature up to 300°C and down to -40°C. The system is specially suited for thermal expansion measurement of electronic components and is frequently used in the development and testing of complex anisotropic materials, components, and structures in electronic applications.
-
Product
Fuel Injection Pressure Tester w/2 Gages & Quick Couplers
53950
-
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
Product
PXI Strain Gauge Simulator Module 4-Channel, 2k
40-265-304
Strain Gauge Simulator
The 40-265 range consists of 6, 4 or 2 channel modules (this version is the 4-channel, 2kΩ) that simulate the operation of a range of strain gauges making it ideal for testing strain gauge meters and a wide variety of industrial control systems. The range provides a simple way of replacing in house developed sensors with a low cost simulator having excellent performance. The 40-265 uses the same resistor bridge techniques that real life strain gauges are based on, ensuring accurate emulation under all conditions.
-
Product
Fiber Optic Strain Sensors
-
Opsens Solutions optical strain sensor delivers reliable results in harsh environment. Opsens Solutions OSP-A fiber optic strain transducers are designed to provide accurate deformation measurement in the most adverse conditions. Its small size and EMI/RFI electromagnetic environment and lightning immunity makes it the ideal sensor for geotechnical, structural health monitoring, Defense and aerospace and general applications.
-
Product
Automatic Transmission & Engine Oil Pressure Tester with 2 Gages
34580
-
Check oil pressure in automotive transmissions and engines. Adapters provide coverage of most domestic and imported cars and light trucks. Includes two gages: Large Gage calibrated from 1-600 PSI (0-4,000 kPa & 0-7.0 BAR) and Small Gage for lower pressure requirement 0-50 PSI (0-3.5 BAR) Large gage can be used for all applications and has hang-up hook. Small gage is for more accurate reading of engine oil pressure where maximum oil pressure does not exceed 50 PSI (3.5 BAR). Includes 6 feet of oil proof hose and 10 assorted fittings. Supplied with instructions in a molded plastic case.
-
Product
Coating Thickness Measurement Gages
-
Coating thickness or dry film thickness (DFT) is an important variable that plays a role in product quality, process control, and cost control. Measurement of film thickness can be accomplished by selecting the best mil gage for the particular application.
-
Product
Digital Strain Gauge Sensor
ZET 7110
-
The ZET 7110 module is intended for measuring the relative deformation using primary transducers based on tension gauges. These may be either assembled tension gauges (force gauges, torque gauges), or detachable tension gauges connected using half-bridge or bridge mode.
-
Product
Signal / High Power, Module, Receiver, TriPaddle , 90 Series, 6/6 Positions, incl. Strain Relief plate
510104307
Receiver Module
Primary mating module 510108281.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
48-Channel High Performance Strain Gauge Measurement Instrument
EX1629
-
48-Channel High Performance Strain Gauge Measurement InstrumentSupports quarter-bridge (120, 350Ω or user defined), half-bridge or full-bridge24-bit ADCs, sampling rates up to 25 kSa/sBuilt in programmable differential excitation -8V to 8VBuilt in selectable bridge completionConfigure signal conditioning excitation and bridge completion on a per channel basisSimple, low-cost wiring using RJ-45 telecom connectorsSupports TEDS for easy transducer detection and setupRJ-45 input connector reduces setup cost and timeBuilt in self-calibration and shunt calibrationSupports voltage, ratiometric and linear measurements other than strain measurements.
-
Product
Height Gages
-
We have a wide range of height gages - from the most basic with scribers to the more sophisticated electronic height gages. We have electronic, dial and vernier height gages that come with a scriber. Scribing height gages are offered in ranges starting at 0-6″/150mm up to 71"/1800mm
-
Product
Fuel Injection Pressure Tester with 2 Gages & Quick Couplers in Storage Case
53980
-
Tests gasoline fuel pump pressure on most domestic and imported fuel injection equipped vehicles.Quick couplers provide for fast and easy hook-up.Kit contains adapters to test all GM vehicles with Multi-port and some Throttle Body Injection (TBI). Tests all Chrysler cars with Multi-port turbos and some TBI.Use on most Ford TBI systems equipped with or without small Schrader test valve.Tests all Ford vehicles with Multi-port fuel injection systems.
-
-
-
Product
Gripmaster Strain Reliefs
-
Multi-Tech Industries, Inc. offers a complete line of all-metal and insulated Gripmaster Strain Reliefs, and hand tools to install the strain reliefs. Please search our product line below and give us a call at 732-431-0550 for additional assistance or to place an order.
-
Product
Bore Gages - Dial
-
Measure internal diameters and bores and are a proper choice when ovality and/or cylindricity is of concern.
-
-
-
Product
Ultrasonic Thickness Gage
27MG
-
The Olympus 27MG is an affordable ultrasonic thickness gage designed to make accurate, measurements from one side on internally corroded or eroded metal pipes, tanks, and other equipment. It weighs only 12 oz. (340 g) and is ergonomically designed for easy, one-hand operation. Thickness range 0.50 mm to 635 mm (0.020 in. to 25.0 in.) depending on material, transducer, surface conditions, temperature.
-
Product
Coax, Module, Receiver, 20/26 GHz/75 Ohm HD, 90 Series, 32 Position, incl. strain relief
510104289
Receiver Module
Primary mating module 510108179.*Please note: VPC receiver modules must be separated into two pieces in order to extract contacts. For detailed instructions please consult the user manual/procedure sheet for this module before extracting contacts.
-
Product
Surface Roughness Gage
1000
-
The Adcole Model 1000 represents the state of the art in surface roughness measurement for crankshafts, camshafts and other cylindrical components. The machine is pre-programmed for optimized workflows. Operators simply need to load and unload the parts. In addition to its unprecedented accuracy, this product is also the fastest system for taking critical surface measurements.The base gage is a rugged, self-standing horizontal granite surface plate with affixed headstock, tailstock and carriage. Scanned data is immediately available for review on the touchscreen monitor or printing.
-
Product
Strain Measurement Trainer Module
-
Unitech Scales And Measurements Pvt. Ltd
Strain Measurement Module comprises of Cantilever Beam bonded with four strain gauges,pan and weights upto 1Kg. Digital 3½ digit indicator module is supplied to read the microstrain.
-
Product
Diaphragm Strain Gauges
-
Diaphragm Strain Gauges provide a full bridge for convenient installation, different diameters, for fitting the intended diaphragm size, are available.
-
Product
High Strain Pile Driving Analyzer, Pile Testing Machine
SG-PDA
-
It is a state-of-the-art testing equipment to perform high strain pile bearing testing on piles.It will provide prediction on the pile bearing capacity, pile integrity, driving stresses and hammer performance for a given pile penetration. It is a relative low cost type of pile testing compared to static load test (MLT or CRP). The testing technique is quick and accurate.It can also be used to perform high strain pile bearing monitoring to evaluate pile driving information for pile bearing capacity, pile integrity, driving stresses and transferred energy against pile penetration. The results are essential for the actual pile driving process and to obtain valuable data on the hammer, pile & soil system for re-design on the piled foundation (if necessary).
