PCIe
Serial architecture local bus with each lane running at 2.5 Gigabits/sec speeding communication between CPU and graphics controller.
See Also: PCI Express, Instrument Control Buses, Modular Instruments, PCI Express Test, PCI Express Analyzers, PCI, Compute Express Link
-
Product
PCIe Mini Module
PCIe-Mini-ESCC
Controller
The PCIe-Mini-ESCC module is a Dual Channel serial communication controller with 4K FIFO per Line. The PCIe-MiniESCC module is based on the Z85230 Enhanced Serial Communication Controller, with larger FIFOs and several SDLC improvements from Zilog.
-
Product
PCIe
M.2 Gen4 Socket2
-
SCHILLER AUTOMATION GmbH & Co. KG
The PCIe Gen4 M.2 Socket 2 test adapter or test fixture kit facilitates Device and Host compliance testing for PCIe Gen4 M.2 Socket 2 Source and Sink devices.
-
Product
Satellite Receiver For PCIe
DTA-2137C
-
Professional satellite receiver for DVB-S and DVB-S2 with two ASI monitoring outputs. This PCIe card outputs the full stream (not just a single service), either as BBFRAMEs or as a transport stream. Several advanced measurement capabilities are supported.
-
Product
PCIe Board
79G5P
-
The 79G5P-TE2C0 is a full-height, half-length, PCIe board fitted & configured with the NAI TE2 function module. The TE2 is a single-channel, tri-redundant, Ethernet communications interface module that supports three traffic classes: Time-Triggered Ethernet SAE AS6802 (TTEthernet™), ARINC 664 Part 7 and Avionics Full-Duplex Switched Ethernet (AFDX®) and IEEE 802.3 protocol.
-
Product
PCIe 3.0 Protocol Analyzer
Summit T3-16
Protocol Analyzer
The Summit T3-16 is Teledyne LeCroy's fifth generation of protocol analyzers targeted at high speed PCI Express I/O-based applications such as workstation, desktop, graphics, storage, and network card applications.
-
Product
PCIe 4.0 Test Platform
PXP-400A
Test Platform
The Teledyne LeCroy PXP-400A Test Platform provides a convenient means for testing PCIe 4.0 cards with a self-contained portable and powered passive backplane. The PXP-400A provides power required for both cards under test, and an interposer can be used for connection to a protocol analyzer.
-
Product
Reflective Memory PCIE card
PCIE-5565PIORC
-
The PCIE-5565PIORC low profile PCI Express (PCIe) Reflective Memory node card provides a high-speed, low latency, deterministic interface that allows data to be shared between up to 256 independent systems (nodes) at rates up to 170 Mbyte/s. Each Reflective Memory board may be configured with 128 MB or 256 MB of onboard SDRAM.The local SDRAM provides fast Read access times to stored data. Writes are stored in local SDRAM and broadcast over a high speed fiber-optic data path to other Reflective Memory nodes.
-
Product
PCIe Mini Card
EXC-1553mPCIe/P1-1760
-
Each channel of the EXC-1553mPCIe/P1-1760 operates simultaneously as a Bus Controller and/or multiple (up to 32) Remote Terminals, or as a Triggerable Bus Monitor. The card supports error injection and detection. The card’s small size and compatibility with notebook computers make it the perfect solution for performing system simulation of the MIL-STD-1760 bus, in the lab and in the field.
-
Product
PCIe to cPCI Bridge
Strain/Bridge Input Module
3U/ 4HP CompactPCI remote controller for use in CompactPCI rear system slot inside a 19″ chassis, PC PCIe interface card for standard desktop PC, allows control of CompactPCI Chassis from desktop PC
-
Product
32-Axis PCIe EtherCAT MainDevice Motion Controller
PCIe-8334
Motion Controller
ADLINK PCIe-8334 is a hardware-based EtherCAT motion controller able to support up to 32 synchronized axes and over 10,000 points simultaneously. The PCIe-8332 features dedicated isolated emergency stop input (EMG), and configurable isolated high-speed digital input as not only generic sensor input but also pulsar input, with up to 1MHz input frequency. Optimum jitter control is provided in minimal cycles of 250µs to optimize synchronous I/O performance for vertical automation applications in semiconductor, electronic manufacturing, and others. The PCIe-8334 provides an out-of-shell application-ready (APS) function library to generate multi-dimensional, highly synchronized, time-deterministic event-triggered motion & I/O control. A wide range of compatible 3rd party SubDevice are easily designed with ADLINK's APS function library. ADLINK's MotionCreatorPro 2 utility is fully compliant with the Microsoft Windows environment, that allows complete EtherCAT motion and I/O configuration and function evaluation as well as compiling program download functions.
-
Product
Intel Xeon E3 Processor AMC, PCIe Gen3
AMC756
-
The AMC756 is a Processor AMC (PrAMC) in a single module, mid-size AdvancedMC (AMC) form factor based on the Intel® Xeon® Processor E3-1505M v6 (Kaby Lake) with CM238 PCH. The processor base frequency is 3.0 GHz with max turbo frequency of 4.0 GHz. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
Product
PCIe Gen 4.0 RAID Adapter
MegaRAID 9580-8i8e
-
The MegaRAID 9500 series is the industry’s first PCIe Gen 4.0 RAID adapter family, offering PCIe Gen 4.0 host and storage interfaces. The MegaRAID 9580-8i8e adapter, based on the SAS3916 high-port count PCIe 4.0 x8 RAID-on-Chip (RoC), delivers twice the performance of previous generations.
-
Product
PCIe High-Speed Digitizer
U5310A
-
The U5310A is a two channel PCIe, DC coupled 10-bit signal acquisition card providing sample rates up to 10 GS/s with 2.5 GHz bandwidth for use in a variety of advanced imaging and processing systems. Featuring unique spurious-free dynamic range (SFDR) and signal-to-noise ratio (SNR) performances in high frequencies, especially at 250 mV full scale range (FSR), the U5310A ADC card is suited for embedded OEM applications requiring signal acquisition at wide bandwidth and high dynamic range.
-
Product
PCIe
SFF 8639 Gen4 (U.2)
-
SCHILLER AUTOMATION GmbH & Co. KG
The 8639G4-TPA-PR test adapter or test fixture kit facilitates Source and Sink compliance testing for SFF-Hosts and Devices. These SFF-8639 Gen4 fixtures utilize the multifunctional connector system supporting single/dual port SATA, dual and MultiLink SAS, and/or up to four (4) port PCIe device configurations. The SFF-8639 Gen4 receptacle fixture will accept devices with plug connectors that are in accordance with SFF-8482, SFF-8630, and SFF-8680.
-
Product
PCIe Remote Control Interface
51-924-001
Remote Control Interface
The kit is supplied with this PCIe card which can plug into any PC PCIe slot, a PXI module for insertion into Slot 1 of a PXI chassis and 3m lead to connect the two parts together. The interface uses a single lane PCIe connection from the PC to provide a software transparent link from the PC PCIe backplane to the PXI backplane. The supplied 3m shielded lead ensures the system has robust operation and an adequate separation distance between the PC and the PXI chassis.
-
Product
3U VPX Extender PCIe Gen3
-
The VPX extender modules are built to extend a 3U or 6U VPX module completely out of a chassis, providing access to all sides of the module for testing and debugging.
-
Product
ARINC825 (CAN Bus) Test & Simulation Module for PCIe
ACPe825-x
Simulator
ARINC825 (CAN bus) Test & Simulation module for PCIe with 2 or 4 electrically isolated CAN bus nodes operating concurrently at CAN bus high speed bit rate of up to 1Mbit/s. The ACP825 PCIe card can work either with full functionality as an active CAN node for testing and simulating or in Listening Only mode for monitoring and recording purposes.
-
Product
PCIe Multi-Terminal Emulator
Sy629PCIe-BPTE
-
The Sy629PCIe-BPTE card provides a convenient means for transmitting and receiving data over an ARINC 629 bus in accordance with the transmit and receive programme defined by data written into the XPP and RPP memory. In particular, this product can emulate up to 120 terminals transmitting on an ARINC-629 data bus whilst correctly maintaining the approved Basic Protocol. This product also offers enhanced facilities to enable a user to insert transmission errors onto the bus and detect and report errors in received messages.
-
Product
PCIe Card MX3 Copper Interface
OTP2 module no.183
-
PXI offers the optimal approach to validation and production testing. You can meet timing, synchronization, and throughput requirements across devices. PXI is a robust PC-based platform for measurement and automation systems, supported by software. PXI combines PCI electrical bus characteristics with CompactPCI's modular Eurocard packaging, and then adds special synchronization buses and important software functions.
-
Product
Intel Xeon E3 Processor AMC, PCIe Gen3
AMC758
-
The AMC758 is a Processor AMC (PrAMC) in a double module, mid-size AdvancedMC (AMC) form factor based on the Intel® Xeon® Processor E3-1505M v6 (Kaby Lake) with CM238 PCH. The processor base frequency is 3.0 GHz with max turbo frequency of 4.0 GHz. The module follows the AMC.1, AMC.2 and the AMC.3 specifications.
-
Product
Ultrascale FPGA PCIe Board
SE100 – Solar Express
-
Sundance Multiprocessor Technology Ltd.
SE100 is based on Xilinx’s Virtex Ultrascale FPGA XCVU190-2FLGC2104E, and is a powerful processing card with plenty of IO capabilities to meet the needs of modern compute-intensive applications such as Supercomputing, Data Centers and defense. The board can optionally be populated with 095, 125, and 160 devices in C2104 package for reduced cost. Host interface is via 8 lanes of PCIe Gen3 but the card can also be used as an embedded, standalone, hardware too. Multiple cards can be cascaded to provide a multi-FPGA system with cards connected together via the board’s fast IO channels to meet the needs of even more demanding applications like ASIC design and Stock Market fast trading systems.
-
Product
16 Relay Output PCIe Board
APCIE-2200-16
-
16 electromechanical relays with change-over contacts The PCI-Express 16 relay board APCIe-2200-16 has 16 relay output channels. The board is especially suited for applications like industrial I/O control, signal switching, alarm monitoring, as interface to machines, for the ON/OFF monitoring of motors, lights etc. in the harsh industrial environment.
-
Product
Domino Symphony PCIe
-
Four 10-bit 65 MHz A/D converters with four 8- or 10-bit LUTsPCIe x1 busD³ technology for extremely low synchronization jitterSupport for mega-pixel progressive-scan and interlaced cameras, asynchronous reset and exposure controlTrigger, strobe and general purpose I/O lines
-
Product
PMC-to-4X PCI Express (PCI-e/PCIe) Adapter
6777
-
The Technobox, Inc. P/N 6777 is a PCI Express (PCIe/PCI-e) carrier that permits the insertion of a single PMC into a PCI-e slot (4X). The adapter orients the PMC in a reverse manner such that the rear I/O from PN4 appears at the 68-pin SCSI-style connector installed on the adapter’s bracket. Furthermore, the reverse orientation of the card permits direct access to the standard front I/O (if any) within the host chassis.
-
Product
PCIe Gen 4 Switch Adapter
P411W-32P
-
The Broadcom P411W-32P is the industry’s first fully managed Gen 4.0 NVMe switch adapter, providing enterprise class options for NVMe solid state drive (SSD) attach requirements. The P411W-32P leverages Broadcom’s world-class board design, PEX88048 PCIe Gen 4.0 switch chip, and solid firmware expertise, to provide advanced features not available using traditional NVMe drive attach methods. Similar to Broadcom HBAs, the P411W-32P adapter is supplied with fully validated and supported firmware and standards based out of band manageability features.
-
Product
PCIe Adapter for PMC
PCIe4LBPCI
-
Now you can use your PCI with a new PC. The new PC´s have PCI Express connectors in larger quantities than PCI slots. PCIe4LBPCI ( PCIe Bridge PCI 1 position) adapter / carrier converter card provides the ability to install one PCI card into a standard PCIe (Express) 4 lane slot. Suitable for PCI or PCI-X operation with the PCI; 32 bit or 64 bit data and PCI (25, 33, 50, 66) or PCI-X (50,66,100,133) MHz. clock. Auto selected or switch programmable speeds. The bridge can operate with 1, 2, 3 or 4 lanes active, and can be installed into slots with more than 4 lanes if desired.
-
Product
PCIe Gen3 Module For PCIe Bus Expansion
PCI123
-
The PCI123 is VadaTech’s 3rd generation PCIe expansion module based on the PCI-SIG specification. The board is a high-speed bridge from the host PCIe bus to VadaTech’s UTC006 PCIe Gen 3 x16 MCH.
-
Product
Adaptive Relay Board, Virtex-6 FPGA - PCIe
Model 78624
-
Model 78624 is a member of the Cobalt® family of high-performance PCI Express boards based on the Xilinx Virtex-6 FPGA. As an IF relay, it accepts two IF analog input channels, modifies up to 34 signals, and thendelivers them to two analog IF outputs. Any signal within each IF band can be independently enabled or disabled, and changed in both frequency and amplitude as it passes through the module. The 78624 supports many useful functions for both commercial and military communications systems including signal drop/add/replace, frequency shifting and hopping, amplitude equalization, and bandwidth consolidation. Applications include countermeasures, active tracking and monitoring, channel security, interception, adaptive spectral management, jamming, and encryption.
-
Product
PCIe Switches And Bridges
-
Modern data centers require solutions that offer maximum performance with minimal power consumption. While compute and storage devices have native PCIe for internal communication, they all use different technologies, such as Ethernet or InfiniBand, to connect externally.
-
Product
UltraZed PCIe Carrier Card for UltraZed-EG System-on-Module
AES-ZU-PCIECC-G
-
The UltraZed PCIe Carrier Card supports the UltraZed-EG System-on-Module (SOM), providing easy access to the full 180 user I/O, 26 PS MIO, and 4 PS GTR transceivers available from the UltraZed-EG SOM via three Micro Headers. Two 140-pin Micro Headers on the carrier card mate with the UltraZed-EG SOM, connecting 180 of the UltraZed-EG Programmable Logic (PL) I/O to 2 Digilent Pmod™ compatible interfaces, FMC LPC slot, LVDS Touch Panel interface, push button switches, DIP switches, LEDs, Xilinx SYSMON, and clock oscillator.
