Bit Error Rate Testers
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received. Also known as: BERT
See Also: BER Testers, BERT
-
product
Electric Vehicle Battery Cell Tester
MCV
The MCV is a low-current life cycle test system for development of primary and rechargeable batteries in various chemistries. Operating from a common microprocessor, multiple circuits in the MCV module can run individual test programs. Additionally, the MCV is designed and built for ease of maintenance and service. The modular construction means that most subassemblies, large or small, remove easily for service outside the cabinet and fast replacement.
-
product
Velcro Tape Fatigue Tester
UI-FT35
Velcro Tape Fatigue Tester is used to test the velcro tape/ hook and loop fastener to repeated closing fatigue resistance ability. Touch and close fastener repeated closing fatigue test is one of the necessary step for velcro strength test no matter for peel strength or shear.strength
-
product
Cable Tester & Cable Tracer & Multi-Functions Lan Tester
M-CT-430A
Fuzhou Metricu Technology Co Ltd
The multifunction LAN tester M-CT-430A is designed for maintenance and installation of cable, cable tracer, and HD Coaxial video level meter test in one equipment. The unit supports detect the near-end, mid-end and far-end fault point of RJ45 cable connector, and also supports Port Flash, PING test, IP address Scan, Link Monitor. Installers take the all in one cable tester, making working conditions safer and increasing productivity.
-
product
Axis Play Tester
PMS 3.5 | VP 225012
Maschinenbau Haldenwang GmbH & Co. KG.
The axis play tester PMS 3.5 is used to reliably determine defects and wear on steering parts, wheel bearings, suspension and suspension by counter-rotating transverse and longitudinal movement of the test plates. The built-in hydraulic drive ensures a powerful and even movement of the test plates. An automatic mode and other different operating modes make the PMS 3.5 easy to use.
-
product
Digital Bit Pattern Generator
FAB-3226
The FAB-3226 Digital Bit Pattern Generator connects digital ports to an user-defined FPGA logic. As the FPGA is user-programmable all kind of operation can be implemented: input, output, and closed loop operation where input and output are processed in real-time. All this can be controlled by an user-defined application program running on a computer system (PC or embedded).
-
product
Non-Contact Voltage Tester
2AC
The Fluke 2AC is the latest addition to the VoltAlert™ AC non-contact voltage tester family. It is designed to be pocket-sized and easy to use. The tip of the pocket-sized tester will glow red when within close proximity of an outlet, terminal strip, or power cord where voltage is present. The 2 AC is always on, with a battery check function to make sure the tester is working properly.
-
product
HL Deadweight Tester
AMETEK Sensors, Test & Calibration
The HydraLite Tester is a primary standard available as a dead weight tester or a gauge. Both feature a re-entrant type measuring piston and cylinder assembly. This design reduces the rate of fluid leakage and increases float time, helping to maintain accuracy as test pressures increase.
-
product
Leeb Hardness Tester
Beijing TIME High Technology Ltd.
A portable, non-destructive tool that measures the hardness of metals by using the dynamic Leeb rebound method.
-
product
Cable & Insulation Testers
A cable insulation resistance test is a test that is performed by applying 500 V or more between the conductor and ground and measuring the resulting leakage current. An insulation resistance tester is a test instrument that measures current that leaks through the insulation into ground. Insulation resistance tests can be performed with insulation multi- meters (IMMs) or megohmmeters. Insulation resistance testers are calibrated to display megohms (MΩ) of resistance. A satisfactory insulation resistance measurement should be in millions of ohms.
-
product
Electric Safety Tester
PV-215
The multifunction device PV-215 allows quickly and safely carrying out the electric safety tests provided for a PV system (section in DC) and the functional test of modules/strings the system consists of according to the requirements of Standard IEC/EN62446.
-
product
Line Tester
CAT 1 TEST
Monacor International GmbH & Co.
Line tester for continuity testing of Cat 5, Cat 6 and ISDN network cables*Connection test with LED display for 8 individual wires and shielding*Continuity, miswire, open, short, crossover, and ground detection*Connector compatibility with the following modular plugs: RJ45 (8P8C), RJ12 (6P6C), RJ11(6P4C, 6P2C)*Network standards supported: Token Ring, 10Base-T, 10Base-T2, 285A, TIA568A/568B*Separate receiver for particularly long and complex cables*The main unit and separate receiver can be attached to one another using a guide rail on the side*Power supply via 9 V block battery (not included)*Supplied with protective bag
-
product
Hipot Tester
19052/19053/19054
The Chroma Hipot Tester 19050 series provide 3 models for choice. The 19052 for AC/DC/IR Hipot testing and insulation resistance (IR) measurements, the 19053 which combines both AC and DC Hipot tests and IR measurements with 8HV scan channel capability into a single compact unit, and the 19054 which combines both AC and DC Hipot tests and IR measurements with 4HV scan channel capability into a single compact unit.
-
product
Micro Hardness Testers
QATM micro hardness testers for Vickers, Knoop and Brinell cover a test load range from 0.25 g to 62.5 kg. All hardness testers are equipped with an intuitive software that allows easy operation, analysis, and documentation of results. Turrets with either 6 or 8 different test diamonds or lenses can be mounted, which makes switching between Vickers, Knoop and Brinell hardness testing very simple.
-
product
Cross Cut Adhesion Tester
1540
The Elcometer 1540 Cross Cut Adhesion Tester is a simple instrument for quickly determining the coating adhesion of a large variety of paints up to 50µm (2 mils) thickness.
-
product
Peel Force Tester
PT-55
V-TEK Peel Force Testers are built to test, confirm, and record proper sealing strength of cover tape to carrier tape. This ensures parts are secure and protected, yet will release at the designated force. The PT-55 Peel Force Tester incorporates new technology and performance features to make set up easy, maintenance minimal, and calibration accurate. The lightweight design can accommodate 8-120mm tape widths and operates at peel speeds of 120mm/min or 300mm/min.
-
product
CT PT Tester
HTFA-103 / 335
Wuhan Huatian Electric Power Automation Co., Ltd.
Used for automatic testing of protective and metrological CT/PT.
-
product
Protocol Conformance Tester
TS-PCT
The R&S®TS PCT is a compact full range protocol conformance test solution in line with GCF and PTCRB requirements. It supports the entire device certification process for protocol testing and can be extended to operator acceptance testing by adding software.
-
product
CellCorder Battery Tester 'EU Series'
CRT - 400
The new CRT-400 is the latest version in the leading line of CellCorder battery test instruments. Lightweight, stylish, rugged and durable. Special features include new user-friendly operation, USB and IR data transfer, modem, graphical reflective LCD display for better contrast, and new cables and clamps.
-
product
Insulating Oil Dielectric Loss Tester
HTYJS-H / 275
Wuhan Huatian Electric Power Automation Co., Ltd.
Used for measuring dielectric loss and resistivity of insulating oil.
-
product
Automatic Oil Tester
Theses tester sets are used for determining the di-electric BDV of insulating oils, both new and in-service from transformers, switchgear and other electrical equipments.
-
product
LAN Packet Tester
LE-590TX
The LE-590TX is a LAN analyzer that connects to a PC's USB2.0 port. In TAP mode, you can capture full duplex data on 10/ 100Base-TX and transmit to the PC at 480Mbps via the USB2.0 interface. In PG mode, you can generate test packets at up to 100Mbps line rate.
-
product
PXIe Digitizer: 100 MSa/s, 14 bit, 100 MHz
M3100A
The M3100A PXIe digitizer is ideal for general purpose digitizer automated test requirements. It offers high channel density with an advanced data acquisition systems (DAQ). The optional real-time sequencing, inter-module synchronization, and graphical FPGA programming software tools expand its capability to enable a number of solutions including angle of arrival (AoA), baseband electronics designs, wireless device manufacturing and multi-channel coherent signal acquisition.
-
product
Semiconductor Testers
Our integrated team of semiconductor test innovators delivers a complete system tailored to achieve your specific objectives, incorporating:Test strategyHardware designSoftware development and integrationManufacturingInstallationProgram managementOngoing support
-
product
Cable/Harness Tester
IST-380
IST Information Scan Technology, Inc.
THE IST MODEL 380 is a portable, stand-alone cable/harness tester for testing any cable up to 128 points. It detects opens, shorts, and miswires within one second by comparing the test result with the golden file or the data learned from a sample good cable. The error messages can be shown on the LCD display or printed out on a printer with the correct wire list needing reworking.
-
product
Hand-Held Battery Load Tester, Alternator and Starter Tester
6026
135 Amp Fix Load Cables. Recessed meter helps protect this hand-held tester from damage and ensures more accurate and reliable outputs. Features easy to use clamps with 300 Amp jaws. Lightweight and easy to use. Imported.
-
product
3-Phase/Motor Rotation Tester
61-521
*Identifies three-phase sequences*Indicates motor rotation*Checks for open phases*For use up to 600V*2-year warranty
-
product
as an 8 bit I/O Port
BL233
The BL232 has 2 commands that let you use its pins directly. If you aren't using the I2C bus, this gives you and easy 8 bit I/O port
-
product
Ball Rebound Tester
Hildebrand Prüf- und Meßtechnik GmbH
The ball rebound tester is used to determine the resilience of foam materials in accordance with DIN EN ISO 8307 and ASTM D 3574.
-
product
Phase Rotation Testers
Our range of phase sequence indicators provide LED indicationof rotation. They are perfect for checking phase sequence in motors, pumps and air conditioning units.
-
product
Pencil Hardness Tester
501
The Elcometer 501 Pencil Hardness Tester has been designed to ensure that the cylindrical pencil lead is maintained at a constant angle of 45° and exerts a force of 7.5N (1.68lbF).
