BERT
Bit Error Rate Testers measure data integrity and express the ratio of received bits that are in error relative to the amount of bits received.
See Also: Bit Error Rate Testers
-
Product
Error Detector Remote Head 32 and 17 Gb/s
N4952A
Bit Error Rate Tester (BERT)
The N4952A is an affordable and compact error detector remote head available in 4 to 17 Gb/s and 5 to 32 Gb/s configurations. Compatible with the N4960A Serial BERT controller, it is the perfect solution to test up to 32 Gb/s per channel for 100 Gigabit Ethernet applications and other high-data rate devices. The N4952A error detector supports PRBS or user patterns and operates up to 32 Gb/s in a single band with no gaps or missing data rates. The remote head allows the test equipment to be located very close to the device under test, eliminating the need for long cables that degrade signal quality.
-
Product
64 Gbaud High-performance BERT
M8040A
Bit Error Rate Tester (BERT)
The Keysight M8040A is a highly integrated BERT for physical layer characterization and compliance testing. With support for PAM-4 and NRZ signals and data rates up to 64 Gbaud (corresponds to 128 Gbit/s) it covers all flavors of 200 and 400 GbE standards.
-
Product
HDMI/Display Port Checker with 4ch x 12Gb/s Tunable BERT & EyeChecker
RB1204-HDMI,RB1204-DP
-
*Low cost continuous 4ch 1G to 12Gb/s Bit Error Ratio Tester (BERT) and Eye Checker
-
Product
NI-5782, 100 MHz Bandwidth Transceiver Adapter Module for FlexRIO
782705-02
Transceiver Adapter Module
The NI‑5782 is ideal for applications that require the acquisition and generation of IF or baseband signals with in-line, real-time processing. You can analyze acquired signals in the PXI FPGA Module for FlexRIO to perform measurements and generate response signals. Application areas include RF modulation and demodulation, channel emulation, bit error rate testing (BERT), signal intelligence, radio frequency identification (RFID) and near-field communication (NFC) test, real-time spectrum analysis, and software defined radio (SDR).
-
Product
BERT Measurement Solutions
-
Bit error rate testers (BERTs) are usually the initial step for communications testing. These instruments generate digital test patterns, typically pseudorandom binary sequences (PRBSs), that drive devices under test (DUTs). Following the transmission of the signal through the link, the receiver in the BERT captures the signal. This setup can be used for multiple testing purposes, such as to evaluate the performance of a transmitter, a receiver, or an optical link.
-
Product
Interference Source, 32 GHz
M8054A
Interference Generator Module
32 GHz interference source blade for the M8040A BERT.
-
Product
E1/Datacom Transmission Analyzer
DTA-BERT
-
DTA-BERT E1/Datacom Transmission Analyzer can perform E1 transmission performance test (BERT) and status monitoring on data link (V.35, V.24/RS232, RS449, RS530, X.21). Model T can also perform G.703-64K bit error test, PCM31/30 test and Jitter test. Featuring comprehensive functions, easy operation and compact design, DTA-BERT provides total solutions for E1 line analysis and maintenance.
-
Product
4-Channel 28Gbps Electrical Bit-Error-Ratio Tester
OPB-04X28
-
The OptoBERT™ OPB04X28 is the industry’s most compact, cost-effective, easy-to-use 4-channel 28Gbps electrical bit-error-ratio tester (BERT) for testing components, cables and systems in R&D and manufacturing environments.
-
Product
Bit Error Rate Tester - MATRIQ
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
-
Product
PAM4 Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
Golight PAM4 BERT integrates a 4-CH or 8-CH multistage pulse pattern generator (PPG) and a highsensitivity error detection (ED) to achieve BER measurement of data transmission in 200Gbps and 400Gbps. PAM4 BERT provide the best solution for automated production testing of 200G and 400G highspeed optical transceiver.
-
Product
Bit Error Rate Testers
-
The FarSync BERT Tester provides a comprehensive, simple to use, line testing utility for asynchronous and synchronous lines. Standard BER test patterns are used with real time error counters, user controlled error injection, full line test statistics and APIs.
-
Product
Bit Error Ratio Testers
-
Keysight’s bit error ratio test (BERT) system enables the most accurate physical-layer design verification of high-speed communication and multi-gigabit digital interfaces. Our expert-level support will help you select the high-performance hardware, control software, receiver test, and automation tools needed to help you master your design.
-
Product
15G Bit-Error-Ratio Tester
OPBX150
-
The OPTELLENT OptoBERT™ OPBX150 is a cost-effective easy-to-use 15G bit-error-ratio tester (BERT) for testing components and systems in R&D and manufacturing environments. The OPBX150 incorporates an internal reference clock, a pattern generator, clock recovery circuits, and a BER analyzer, in one compact module that provides electrical and optical interfaces at data rates up to 14.025 Gb/s. The OPBX150 is offered with an RS-232 or USB interface and a standard 2-year warranty.
-
Product
Multi-Instrument BERT Software
N4980A
-
The Keysight N4980A multi-instrument BERT software provides the ability to control multiple instruments through a rich Windows-based graphical user interface (GUI). Bit error rate measurements are simple to set up with the intuitive control screens. The software is ideal for setting up and performing parallel BER measurements and jitter tolerance testing (N4980A-JTS) in multi-lane and SERDES devices. You can also create your own patterns using the powerful editing tools built into the pattern editor to meet your unique requirements.
-
Product
Hand Portable Test Instruments
-
GL’s PacketExpert™ 10G provides comprehensive testing of 10 Gbps wirespeed Ethernet/IP networks. It has two 10 Gbps Optical ports, and two 10/100/1000 Mbps Electrical/Optical ports capable of BERT, Smart Loopback, RFC 2544, ExpertSAM, Record and Playback, IPLinkSim™ and PacketBroker functionalities.
-
Product
NRZ Bit Error Rate Tester
-
Shenzhen Golight Technology Co.,Ltd
BERT integrates pulse pattern generator(PPG) and high sensitivity error detector(ED) to achieve the error rate measurement of data transmission in high speed communication. BERT can support multi-channel output and input and output polarity upset. It provides a best solution for the automated production test of the high speed optical transceiver.
-
Product
QAM And PCM Analyzers
-
GAOTek provides a wide range of high performance and inexpensive QAM/PCM analyzers. Quadrature amplitude modulation (QAM) and pulse code modulation (PCM) analyzers are convenient instruments with top to bottom estimations and adaptable setups. Additionally, these devices have integrated functions of analog signal generators/receivers, BERT, signaling generators/receivers, selective level meters, ring generators/ identifications, dialers, DC loop circuits (ICT, OGT), balanced bridges and reflecting bridges into solitary instruments. These analyzers are ideal for installing and maintaining digital and analog networks.
-
Product
Bit Error Rate Tester
100G NRZ BERT
-
The C-BERT 2810-4 is a complete bit error rate tester dedicated for 100G Ethernet applications. The four independent channels enable an actual operating environment with traffic on all lanes. The simultaneous testing of 4 channels is much faster than testing each channel individually saving time and money. The BERT eye scan reveals low-probability events and shows the true performance of the DUT to aid troubleshooting. The high RF port density eliminates long cable length which degrades the signal at 25 Gb/s. The OS independent GUI is easy to install and enable remote control from everywhere. The complete and compact C-BERT is a powerful and cost efficient test solution for 100G Ethernet.C-BERT MI-PE2810-4 Product sheet_rev05.
-
Product
Bit Error Rate Testers
FarSync BERT Tester – USB
-
A Bit Error Rate sync and async communications line quality tester for a Windows Laptop/PC using a USB port. The FarSync BERT provides a comprehensive, simple to use, all in one, line testing utility for testing synchronous lines from your Laptop. There are no extra expensive modules to buy to test different line types.
-
Product
Bit-Error-Ratio Tester
OPBX280
-
The OPTELLENT OptoBERT™ OPBX280 is a cost-effective easy-to-use bit-error-ratio tester (BERT) for testing components and systems in R&D and manufacturing environments at data rates up to 28 Gb/s. The OPBX280 incorporates an internal reference clock, a pattern generator, clock recovery, and a BER analyzer, in an extremely compact module.
-
Product
MIPI M-PHY V5.0 Receiver Test Software (Frame Generator)
N5991MM5E
-
Generate MIPI M-PHY 5.0 sequences and signaling at HS-GEAR5 and lower speeds, for debugging, troubleshooting, and conformance test purposes, using the N5991MM5E Frame Generator software, for the M8040A BERT platform.
-
Product
Bit-Error-Ratio Tester
OPB04X10
-
The OptoBERT™ OPB04X10 is the industry’s most compact, cost-effective, easy-to-use multi-channel multi-rate electrical or optical bit-error-ratio tester (BERT) for testing components, cables and systems. The OPB04X10 is ideal for simultaneously testing multiple channels for sensitivity, cross-talk penalty, etc. at data rates up to 11.5 Gb/s.
-
Product
400, 200, 100 Gbit Error Rate Tester
PAM-4 BERT
-
The MI-PE5610-1 is a PAM-4 BERT with an integrated propriety, optical PAM-4 modulator. ROSA testing is tremebous simpliefied by the integration of the optical PAM-4 modulator in the BERT chassis. This ROSA testing solution saves time and avoids trouble shooting and accelerates your product development. The BERT provides an excellent optical PAM-4 reference output signal with adjustable OMA of the three PAM-4 eyes.The implemented 3-Eye BER technique measures the BER in real time of the 3 eyes simultanously.A wide range of selectable pattern for compliance test and signal analysis is supported.
-
Product
4-Channel 32 Gbps Bit-Error-Rate Tester
OptoBERT™ OPB-100G
-
The OptoBERT™ OPB-100G is the industry’s most compact, cost-effective, easy-to-use 4-channel 32 Gbps electrical bit-error-ratio tester (BERT) for testing components, cables and systems in R&D and manufacturing environments.
-
Product
Electrical and Optical & Bit-Error-Rate Testers (BERTs)
OptoBERT™
-
The OptoBERT family of BERTs offers the best value in the industry for bit-error-ratio testing of optical and electrical components, subsystems and systems. OptoBERT family of products covers data rates from 100 Mb/s to 28.05 Gb/s.
-
Product
Bit Error Test & Arbitrary Waveform Generation
-
SHF Communication Technologies AG
SHF’s Bit Pattern Generators (BPG) or Pulse Pattern Generators (PPG), Error Analyzers (EA) and remote heads form a Bit Error Ratio Tester (BERT) suite, which supports a vast number of different applications including high speed Ethernet rates like 100GbE, 200GbE, 400GbE and 1TbE. When it comes to signal generation an Arbitrary Waveform Generator (AWG) is the all-in-one device suitable for every purpose in Telecommunication, Optics, Medicine, Radar, Physics or even Quantum Computing.
-
Product
Bit Error Rate Tester - PXI
BERT 1001/1005 Series
Tester
The BERT is 2 or 4-channel PPG and Error Detector for the design, characterization and production of optical transceivers and opto-electrical components at data rates up to 30 Gb/s.With scalability and exceptional signal fidelity, it is a cost effective test solution for 400 Gb/s communication eco-systems.
-
Product
Serial Bit Error Ratio Testers
-
Developing next-generation technology requires world-class signal integrity and analysis capability. Keysight offers the widest choice of serial bit error ratio test (BERT) products for accurate and efficient characterization, compliance, and manufacturing test for digital interfaces in computer, video, datacom, and telecom applications operating up to 40 Gb/s. Keysight’s breakthrough technology enables you to conquer even the most difficult measurement challenges.
-
Product
AXIe M8000 Series of BER Testers
Bit Error Rate Tester (BERT)
Simplified time-efficient testing is essential when you are developing next-generation computer, consumer, or communication devices. The Keysight M8000 Series is the highly integrated BER test solution for physical layer characterization, validation, and compliance testing. With support for a wide range of data rates and standards, the M8000 Series provides accurate, reliable results that accelerate your insight into the performance margins of high-speed digital devices.
