Showing results: 1771 - 1785 of 2524 items found.
-
M9818AS -
Keysight Technologies
The PXI vector component analyzer enables complex multiport device characterization with continuous wave and modulated signal measurements.
-
16196C -
Keysight Technologies
The 16196C surface mount devices (SMD) test fixture offers excellent repeatability and usability, with accurate correlation up to 3 GHz. 16196 series fixtures are custom designed to fit specific SMD sizes (see table below), and provide repeatable DUT positioning with reliable contacts to enable stable measurement results - reducing the possibility of operator-induced error. Traditionally, SMD inductor evaluation up to 3 GHz has been difficult to implement - now with the 16196 series, it’s easy to perform accurate and repeatable measurements.
-
85521A -
Keysight Technologies
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
11500JK10 -
Keysight Technologies
Connect test ports to devices, fixtures, or probe tips with this 10-cm cable
-
S960240B -
Keysight Technologies
Add pulsed-RF measurement capabilities to your E5081A ENA-X vector network analyzer.
-
S930709B -
Keysight Technologies
S930709B enables fast and accurate active device modulation distortion characterization under modulated stimulus conditions up to 90 GHz. The wide dynamic range and vector error correction of the PNA-X results in an extremely low residual EVM of the test setup, delivering you a complete picture of your device’s performance without test system interference. S930709B measures EVM, NPR, ACPR, and decomposes nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
S970906B -
Keysight Technologies
Add spectrum analysis to your P50xxB Streamline series vector network analyzer
-
85518A -
Keysight Technologies
Easily calibrate non-insertable devices with this module combining an open, short, load, and through in a compact unit
-
U1832C -
Keysight Technologies
The USB-powered (USB TMC compliant) U1832C provides broadband noise figure measurements from 500 MHz – 50 GHz with modular signal analyzer, benchtop X-Series signal analyzers and Fieldfox
-
N5293AX51 -
Keysight Technologies
The N5293AX51 modules are compact lightweight modules designed to interface to the N5292A test set controller that is driven with a PNA/PNA-X B model vector network analyzer.
-
P9165A -
Keysight Technologies
P9165A 2x8 USB solid state switch matrix, 300 KHz to 6.5 GHz is a full cross-bar switch matrix that provides a switch based multiport VNA solution in the form of compact USB controlled involving larger scale of multi-DUT or multiport measurements such as 5G massive MIMO antenna measurement and others.
-
N5186A -
Keysight Technologies
Compact, four-channel vector signal generator capable of signal generation up to 8.5 GHz with 960 MHz of modulation bandwidth per channel
-
S930701B -
Keysight Technologies
S930701B enables fast and accurate active-device modulation distortion characterization under modulated stimulus condition up to 13.5 GHz. The wide dynamic range and vector error correction of the PNA-X result in an extremely low residual EVM of the test setup, so you can get a complete picture of your device’s performance without test system interference. S930701B can measure EVM, NPR, ACPR, and can decompose nonlinear signals and linear signals with the spectral correlation between input and output spectrum without doing demodulation. Integration with the PNA-X SCCM provides quick modulation distortion measurements while making other VNA measurements.
-
85134H -
Keysight Technologies
The Keysight 85134H is a 62.9 cm (24.75 in) long1 flexible cable with a 2.4 mm female2 to 3.5 mm male connector. Cable frequency range is dc to 26.5 GHz with a return loss greater than or equal to 16 dB. Insertion loss is 0.31 * sqrt (f) + 0.2 (where f is frequency is GHz) for the test port connector and 1.8 dB at maximum frequency for the device connector. Phase stability of semi-rigid/flexible cables is characterized with a 90 degree bend using a 2.5 inch radius. Stability1 of the Keysight 85134H is less than 0.12 dB and phase is less than 0.13o * f + 0.5o, (where f is frequency in GHz).
-
85091D -
Keysight Technologies
The Keysight 85091D RF electronic calibration (ECal) module makes the calibration of vector network analyzers fast, easy, and accurate. ECal is a precision, single-connection calibration technique for your vector network analyzer. Performing a full two-port calibration takes less than half the time and a number of connections using ECal versus mechanical calibration kits. Furthermore, the accuracy of the calibration is comparable between electronic and mechanical methods. Traditional mechanical calibrations require intensive operator interaction, which is prone to errors. With ECal, the operator simply connects the ECal module to the network analyzer and the software controls the rest.