Showing results: 1 - 15 of 2945 items found.
-
Micro Lambda Wireless, Inc.
With standard designs covering 250 MHz to 20 GHz, Micro Lambda Wireless is the industry leader in YIG-tuned frequency synthesizers. From low cost single loop designs, to wideband configurations that outperform some test equipment, Micro Lambda is your full service designer and supplier of microwave YIG synthesizers.
-
Pasternack Enterprises, Inc.
The 60 GHz transmitter and 60 GHz receiver modules open up ultra high speed, high bandwidth data transmission for widespread use. Pasternack 60 GHz waveguide modules utilizes the globally unlicensed millimeter wave spectrum of 57 GHz to 64 GHz. Our wireless 60 GHz waveguide transmitter and receiver components are ideal for meeting the high speed data transmission needs of companies and developers.
-
346CK40 -
Keysight Technologies
The Keysight 346CK40 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 40 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source greatly reduces measurement uncertainty, which are commonly reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 14 dB at 1 GHz, decreasing to 5 dB at 40 GHz (typical).
-
346CK01 -
Keysight Technologies
The Keysight 346CK01 is the ideal companion to Keysight´s noise figure solutions when working on high frequency applications. Since it is broadband (1 GHz to 50 GHz), it eliminates the necessity for several sources at different frequency bands. The low SWR of the noise source reduces a major source of measurement uncertainty, which are reflections of the test signals. This is a coaxial noise source with a 2.4 mm coaxial connector. ENR typically 20 dB at 1 GHz, decreasing to typically 7 dB at 50 GHz.
-
773D -
Keysight Technologies
The Keysight 773D is a high-performance directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler is ideal for leveling broadband sources when used with a Keysight 8474B detector. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
E5053A -
Keysight Technologies
The E5053A microwave downconverter is designed to operate with the E5052A/B signal source analyzer (SSA). When configured with the E5053A microwave downconverter, the E5052A/B SSA offers exceptional phase noise sensitivity up to 26.5 GHz. Additionally, combining a pair of 11970 series harmonic mixers offers the phase noise measurement up to 110 GHz.
-
772D -
Keysight Technologies
The Keysight 772D is a high-performance, dual-directional coupler designed for broadband swept measurements in the 2 to 18 GHz range. This coupler can be combined with Keysight power sensors and power meters for reflectometer applications. Forward and reverse power measurements on transmitters, components, or other broadband systems are made simpler using the Keysight 772D. The broadband design allows the use of a single test setup and calibration for tests spanning the entire 2 to 18 GHz range.
-
87415A -
Keysight Technologies
The Keysight 87415A microwave component amplifier brings compact, reliable gain block performance to systems integrators and microwave designers. With 25 dB minimum gain and over 23 dBm output power from 2 to 8 GHz, this amplifier offers output power where it is needed: at the test port.
-
83018A -
Keysight Technologies
The Keysight 83018A microwave system amplifier is a compact, off-the-shelf amplifier designed for systems designers and integrators. This amplifier provides power where you need it to recover system losses and to boost available power in RF and microwave ATE systems. The ultrabroad bandwidth from 2 to 26.5 GHz allows the designer to replace several narrow bandwidth amplifiers with a single Keysight amplifier, eliminating the need for crossover networks or multiple bias supplies. The standard Keysight 83018A includes internal directional detectors for external leveling applications. With excellent noise figure relative to its broad bandwidth and high gain, this amplifier significantly improves system noise figure and dynamic range. The Keysight 83018A comes equipped with a low profile heat sink, an integral mounting bracket, and a two-meter dc power supply cable. Thermal characteristics and power supply design allow fast, easy integration into most measurement systems.
-
Pasternack Enterprises, Inc.
Pasternack antennas for 60 GHz applications, also referred to as 60 GHz gain horn antennas or horn antennas, are broadband passive devices to direct a beam radio waves at a precise frequency. Antennas for 60 GHz from Pasternack use either a UG-385/U or a UG-387/U flange size.
-
-
Fairview Microwave Inc.
Fairview Microwave’s waveguide to coax adapters are made up of 77 models ranging in sizes from WR-10 to WR-430. These waveguide to coaxial adapters are offered in a broad selection of waveguide sizes, flanges, connectors and materials. Fairview’s waveguide to coax adapters support 10 different types of coax connectors and are available with UG (square/round cover), CMR, CPR, UDR and PDR-style flanges. Additionally, these waveguide to coax adapters deliver VSWR performance as low as 1.25:1 and are available with aluminum, gold-plated aluminum, gold-plated copper or painted copper alloy finishes.
-
87304C -
Keysight Technologies
The Keysight 87304C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.
-
87302C -
Keysight Technologies
The Keysight 87302C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.
-
87303C -
Keysight Technologies
The Keysight 87303C hybrid power divider is designed for power splitting applications that require minimal insertion loss and high isolation between ports. It has insertion loss between the main line and output port which is 1 to 2 dB less than equivalent resistive power splitters. It is designed for critical signal processing applications; phase and amplitude tracking between the two output ports is controlled and specified.